A. Duda

40.8% efficient inverted triple-junction solar cell with two independently metamorphic junctions

A photovoltaic conversion efficiency of 40.8% at 326 suns concentration is demonstrated in a monolithically grown, triple-junction III–V solar cell structure in which each active junction is composed of an alloy with a different lattice constant chosen to maximize the theoretical efficiency. The semiconductor structure was grown by organometallic vapor phase epitaxy in an inverted configuration with a 1.83 eV Ga.51In.49P top junction lattice-matched to the GaAs substrate, a metamorphic 1.34 eV In.04Ga.96As middle junction, and a metamorphic 0.89 eV In.37Ga.63As bottom junction. The two metamorphic junctions contained approximately 1×105 cm−2 and 2–3×106 cm−2 threading dislocations, respectively.

High-efficiency GaInP∕GaAs∕InGaAs triple-junction solar cells grown inverted with a metamorphic bottom junction

The authors demonstrate a thin, Ge-free III–V semiconductor triple-junction solar cell device structure that achieved 33.8%, 30.6%, and 38.9% efficiencies under the standard 1sun global spectrum, space spectrum, and concentrated direct spectrum at 81suns, respectively. The device consists of 1.8eV Ga0.5In0.5P, 1.4eV GaAs, and 1.0eV In0.3Ga0.7As p-n junctions grown monolithically in an inverted configuration on GaAs substrates by organometallic vapor phase epitaxy. The lattice-mismatched In0.3Ga0.7As junction was grown last on a graded GaxIn1−xP buffer. The substrate was removed after the structure was mounted to a structural “handle.” The current-matched, series-connected junctions produced a total open-circuit voltage over 2.95V at 1sun.

Optical enhancement of the open-circuit voltage in high quality GaAs solar cells

The self-absorption of radiated photons increases the minority carrier concentration in semiconductor optoelectronic devices such as solar cells. This so-called photon recycling leads to an increase in the external luminescent efficiency, the fraction of internally radiated photons that are able to escape through the front surface. An increased external luminescent efficiency in turn correlates with an increased open-circuit voltage and ultimately conversion efficiency. We develop a detailed ray-optical model that calculates Voc for real, non-idealized solar cells, accounting for isotropic luminescence, parasitic losses, multiple photon reflections within the cell and wavelength-dependent indices of refraction for the layers in the cell. We have fabricated high quality GaAs solar cells, systematically varying the optical properties including the back reflectance, and have demonstrated Voc = 1.101 ± 0.002 V and conversion efficiencies of (27.8 ± 0.8)% under the global solar spectrum. The trends shown by th...

Lattice-mismatched approaches for high-performance, III-V photovoltaic energy converters

We discuss lattice-mismatched (LMM) approaches utilizing compositionally step-graded layers and buffer layers that yield III-V photovoltaic devices with performance parameters equaling those of similar lattice-matched (LM) devices. Our progress in developing high-performance, LMM, InP-based GaInAs/InAsP materials and devices for thermophotovoltaic (TPV) energy conversion is highlighted. A novel, monolithic, multi-bandgap, tandem device for solar PV (SPV) conversion involving LMM materials is also presented along with promising preliminary performance results.

Structure, chemistry, and growth mechanisms of photovoltaic quality thin‐film Cu(In,Ga)Se2 grown from a mixed‐phase precursor

The formation chemistry and growth dynamics of thin‐film CuInSe2 grown by physical vapor deposition have been considered along the reaction path leading from the CuxSe:CuInSe2 two‐phase region to single‐phase CuInSe2. The (Cu2Se)β(CuInSe2)1−β (0<β≤1) mixed‐phase precursor is created in a manner consistent with a liquid‐phase assisted growth process. At substrate temperatures above 500 °C and in the presence of excess Se, the film structure is columnar through the film thickness with column diameters in the range of 2.0–5.0 μm. Films deposited on glass are described as highly oriented with nearly exclusive (112) crystalline orientation. CuInSe2:CuxSe phase separation is identified and occurs primarily normal to the substrate plane at free surfaces. Single‐phase CuInSe2 is created by the conversion of the CuxSe into CuInSe2 upon exposure to In and Se activity. Noninterrupted columnar growth continues at substrate temperatures above 500 °C. The addition of In in excess of that required for conversion produce...

Efficient heterojunction solar cells on p-type crystal silicon wafers

Efficient crystalline silicon heterojunction solar cells are fabricated on p-type wafers using amorphous silicon emitter and back contact layers. The independently confirmed AM1.5 conversion efficiencies are 19.3% on a float-zone wafer and 18.8% on a Czochralski wafer; conversion efficiencies show no significant light-induced degradation. The best open-circuit voltage is above 700 mV. Surface cleaning and passivation play important roles in heterojunction solar cell performance.

Single-wall carbon nanotube networks as a transparent back contact in CdTe solar cells

Single-wall carbon nanotube (SWCNT) networks form a highly transparent and electrically conductive thin film that can be used to replace traditional transparent conducting oxides (TCOs) in a variety of applications. Here, the authors demonstrate their use as a transparent back contact in a near-infrared (NIR) transparent CdTe solar cell. SWCNT networks are hole-selective conductors and have a significantly greater NIR transparency than TCOs—qualities which could both make them very useful in tandem thin-film solar cells. SWCNT networks can be incorporated into single-junction CdTe devices and in CdTe top cells for mechanically stacked thin-film tandem devices, as described here. The best device efficiency using SWCNTs in the back contact was 12.4%, with 40%–50% transmission between 800 and 1500nm.

Effects of Internal Luminescence and Internal Optics on

For solar cells dominated by radiative recombination, the performance can be significantly enhanced by improving the internal optics. We demonstrate a detailed model for solar cells that calculates the external luminescent efficiency and discuss the relationship between the external and internal luminescence. The model accounts for wavelength-dependent optical properties in each layer, parasitic optical and electrical losses, multiple reflections within the cell, and assumes isotropic internal emission. For single-junction cells, the calculation leads to Voc, and for multijunction cells, the calculation leads to the Voc of each junction as well as the luminescent coupling constant. In both cases, the effects of the optics are most prominent in cells with high internal radiative efficiency. Exploiting good material quality and high luminescent coupling, we demonstrate a two-junction nonconcentrator cell with a conversion efficiency of (31.1 ± 0.9)% under the global spectrum.

V_{\bf oc}

We present results for quadruple-junction inverted metamorphic (4J-IMM) devices under the concentrated direct spectrum and analyze the present limitations to performance. The devices integrate lattice-matched subcells with rear heterojunctions, as well as lattice-mismatched subcells with low threading dislocation density. To interconnect the subcells, thermally stable lattice-matched tunnel junctions are used, as well as a metamorphic GaAsSb/GaInAs tunnel junction between the lattice-mismatched subcells. A broadband antireflection coating is used, as well as a front metal grid designed for high concentration operation. The best device has a peak efficiency of (43.8 ± 2.2)% at 327-sun concentration, as measured with a spectrally adjustable flash simulator, and maintains an efficiency of (42.9 ± 2.1)% at 869 suns, which is the highest concentration measured. The Voc increases from 3.445 V at 1-sun to 4.10 V at 327-sun concentration, which indicates high material quality in all of the subcells. The subcell voltages are analyzed using optical modeling, and the present device limitations and pathways to improvement are discussed. Although further improvements are possible, the 4J-IMM structure is clearly capable of very high efficiency at concentration, despite the complications arising from utilizing lattice-mismatched subcells.

and

We demonstrate high efficiency performance in two ultra-thin, Ge-free III–V semiconductor triple-junction solar cell device designs grown in an inverted configuration. Low-stress metamorphic junctions were engineered to achieve excellent photovoltaic performance with less than 3 × 106 cm−2 threading dislocations. The first design with band gaps of 1.83/1.40/1.00 eV, containing a single metamorphic junction, achieved 33.8% and 39.2% efficiencies under the standard one-sun global spectrum and concentrated direct spectrum at 131 suns, respectively. The second design with band gaps of 1.83/1.34/0.89 eV, containing two metamorphic junctions achieved 33.2% and 40.1% efficiencies under the standard one-sun global spectrum and concentrated direct spectrum at 143 suns, respectively.