A. Fok

Non-destructive examination of interfacial debonding using acoustic emission

OBJECTIVESnThis study aims to assess the viability of using the acoustic emission (AE) measurement technique to detect and monitor in situ the interfacial debonding in resin composite restorations due to build-up of shrinkage stresses during polymerization of the composite.nnnMATERIALS AND METHODSnThe non-destructive testing technique that measures acoustic emission (AE) was used to detect and monitor the interfacial debonding in resin composite during curing of the composite. Four groups of specimens, n=4 each, were tested: (1) intact human molars with Class-I cavities restored with the composite Z100 (3M ESPE, USA); (2) intact human molars with Class-I cavities restored with the composite Filtek™ P90 (3M ESPE, USA); (3) ring samples prepared from the root of a single bovine tooth and restored with Z100; (4) freestanding pea-size specimens of Z100 directly placed on the AE sensor. The restorations in Groups (1)-(3) were bonded to the tooth tissues with the adhesive Adper™ Scotchbond™ SE Self-Etch (3M ESPE, USA). The composites in all the specimens were cured with a blue light (3M ESPE, USA) for 40s. The AE signals were recorded continuously for 10 min from the start of curing. Non-destructive 3D imaging was performed using X-ray micro-computed tomography (micro-CT) to examine the bonding condition at the tooth-restoration interface.nnnRESULTSnThe development of AE events followed roughly that of the shrinkage stress, which was determined separately by the cantilever beam method. The number of AE events in the real human tooth samples was more than that in the ring samples, and no AE events were detected in the pea-size specimens placed directly on the AE sensor. The number of AE events recorded in the specimens restored using Z100 was more than that found in specimens restored with Filtek P90. The micro-CT imaging results showed clear interfacial debondings in the tooth specimens restored with Z100 after curing, but no clear debonding was found in the P90 specimens.nnnCONCLUSIONSnThe AE technique is an effective tool for detecting and monitoring in situ the interfacial debonding of composite restorations during curing. It can potentially be employed to evaluate the development of shrinkage stress and the quality of interfacial bonds in teeth restored with different composite materials, cavity geometries, and restorative techniques.

An acoustic emission study on interfacial debonding in composite restorations

OBJECTIVEnThis paper studied in vitro the effect of the C-factor on interfacial debonding during curing of composite restorations using the acoustic emission (AE) technique. Finite element (FE) analyzes were also carried out to evaluate the interfacial stresses caused by shrinkage of the composite resin in restorations with different C-factors.nnnMATERIALS AND METHODSnTwenty extracted third molars were divided into 4 groups of 5. They were cut to form Class-I (Groups 1 and 2) and Class-II (Groups 3 and 4) cavities with different C-factors. The average C-factors of the four groups were 3.37, 2.88, 2.00, and 1.79, respectively. The cavities were then applied with an adhesive and restored with a composite, which was cured by a halogen light for 40 s. A 2-channel AE system was used to monitor the interfacial debonding, caused by shrinkage stress, between the tooth and restoration through an AE sensor attached to the surface of the specimen. Recording of the AE started at the same time as curing of the composite and lasted 10 min. Simplified FE models were used to evaluate the interfacial stresses in restorations with different C-factors, with a thermal load (temperature decrease) being applied to the composite resin to simulate its shrinkage.nnnRESULTSnThe mean and standard deviation of the total number of AE events for the four groups were 29.6±15.7, 10.0±5.8, 2.6±1.5, and 2.2±1.3, i.e. the number of AE events increased with an increase in the C-factor. The FE results also showed that, the higher the C-factor of the restoration, the higher the interfacial tensile stress between the tooth and restoration.nnnSIGNIFICANCEnFrom the results of the AE tests and FE simulations, it can be concluded that, the higher the C-factor, the higher the shrinkage stress and the more likely is interfacial debonding.

Fracture simulation of restored teeth using a continuum damage mechanics failure model

OBJECTIVEnThe aim of this paper is to validate the use of a finite-element (FE) based continuum damage mechanics (CDM) failure model to simulate the debonding and fracture of restored teeth.nnnMATERIALS AND METHODSnFracture testing of plastic model teeth, with or without a standard Class-II MOD (mesial-occusal-distal) restoration, was carried out to investigate their fracture behavior. In parallel, 2D FE models of the teeth are constructed and analyzed using the commercial FE software ABAQUS. A CDM failure model, implemented into ABAQUS via the user element subroutine (UEL), is used to simulate the debonding and/or final fracture of the model teeth under a compressive load. The material parameters needed for the CDM model to simulate fracture are obtained through separate mechanical tests. The predicted results are then compared with the experimental data of the fracture tests to validate the failure model.nnnRESULTSnThe failure processes of the intact and restored model teeth are successfully reproduced by the simulation. However, the fracture parameters obtained from testing small specimens need to be adjusted to account for the size effect. The results indicate that the CDM model is a viable model for the prediction of debonding and fracture in dental restorations.