A. J. Paleo

The piezoresistive effect in polypropylene—carbon nanofibre composites obtained by shear extrusion

The piezoresistive effect on poly(propylene) (PP)–carbon nanofibre (CNF) composites fabricated by twin-screw extrusion and compression moulding has been investigated. The electrical and mechanical properties of PP/CNF composites have been obtained as a function of CNF concentration. Electrical conductivity exhibited low thresholds and values close to the required levels for EMI shielding applications at 2.4 vol%. Meanwhile the elastic modulus showed an enhancement with a maximum up to 130% for one of the composites at 0.9 vol% loading. Further, the piezoresistive response has been evaluated in four-point bending. Positive gauge factors between 2 and 2.5 have been obtained. The highest gauge factors are found within the percolation threshold. The characteristics of the materials and the production technique make them suitable for large scale applications.

Piezoresistive effect in spin-coated polyaniline thin films

Polymeric materials have been replacing other materials in various applications, from structural to electronic components. In particular, since the discovery of conducting polymers, the use of these materials is growing up in the manufacture of electronic components, such as organic light-emitting diodes, organic electrodes, energy storage devices and artificial muscles, among others. On the other hand, examples of sensors of conductive polymers based on the piezoresistive effect, with large potential for applications, are not sufficiently investigated. This work reports on the piezoresistive effect of an intrinsically conductive polymer, polyaniline, which was prepared in the form of thin films by spin coating on polyethylene terephthalate substrates. The relationship between electrical response and mechanical solicitations is presented for different preparation conditions. The values of the gauge factor ranges from 10 to 22 for different samples and demonstrates the viability of these materials as piezoresistive sensors.

Polypropylene-Carbon Nanofiber Composites as Strain-Gauge Sensor

Polymeric materials have been replacing other materials in various applications, from structural to electronic components. In particular, since the discovery of conducting polymers and the beginning of the manufacture of conducting composites with carbon fillers, their use in electronics has been growing. A group of electronic components with large potential for industrial applications such as structural monitoring, biomedical, or robotics are sensors based on the piezoresistive effect, fabricated from conductive polymers and/or composites. The aim of this article is to characterize the piezoresistive effect of conductive polymer composites based on polypropylene filled with carbon nanofibers, and to demonstrate a way of fabricating strain gauges from these materials, using industrial techniques. With this purpose, some films are prepared by shear extrusion, which allows the composites to be produced industrially in a standard nonexpensive process. Then, the dependence of the electrical response both on the preparation conditions and on the mechanical solicitations is measured. The obtained gauge factor values, up to 2.5, and piezoresistive coefficients up to 0.0019 mm2/N, prove the viability of these materials for fabricating strain-gauges, where their main advantages are the lower price and the ability to deal with much higher deformations, when compared to metal or semiconductor strain-gauges.

Thermal, dielectrical and mechanical response of α and β-poly(vinilydene fluoride)/Co-MgO nanocomposites

Nanocomposites of the self-forming core-shell Co-MgO nanoparticles, which were of approximately 100 nm in diameter, and poly(vinylidene fluoride) (PVDF) polymer have been prepared. When the polymer is crystallized in the α-phase, the introduction of the nanoparticles leads to nucleation of the γ-phase of PVDF, increasing also the melting temperature of the polymer. With the introduction of the Co-MgO particles, the dielectric constant of the material slightly increases and the storage modulus decreases with respect to the values obtained for the pure polymer.

Glycerol/PEDOT:PSS coated woven fabric as a flexible heating element on textiles

A polyamide 6,6 (PA66) fabric pre-treated with a double barrier dielectric (DBD) atmospheric plasma in air was coated with 1 and 5 layers of an intrinsically conducting glycerol-doped PEDOT:PSS polymer (PEDOT:PSS + GLY) with the final objective of developing a cost-competitive and temperature controllable flexible-heating element to be used in clothing encapsulated between an outer and an inner separator layer in order to provide heat-reflecting properties and uniform temperature distribution, respectively. FTIR, DSC, TGA, SEM, EDS, XRD and DMA analyses show significant changes in morphology, chemistry, enthalpy, crystallinity and glass transition temperature confirming that PEDOT:PSS and glycerol are not only spread over the PA66 yarn surfaces but are dispersed in the bulk facilitating relaxation and increasing structure and chain flexibility. Electrochemical and electrical resistivity (ρ) measurements confirm that the plasma treated PA66 coated with 5 layers of PEDOT:PSS + GLY presents the highest stability, resistance and capacitive behaviour, and the best capability of storing electrical energy. This configuration needs only 7.5 V to induce a temperature change up to 38 °C at a current density of 0.3 A g−1. The desired temperature is easily adjustable as a function of the applied voltage and by the number of coated layers of PEDOT:PSS + GLY. Despite the need to improve the uniformity of the coating thickness on the fabric for uniform heat generation, the observed results are quite impressive since they can be compared to the temperature obtained in carbon nanotube composites using similar voltages. This cost-competitive, safe, highly flexible and stable thermoelectric fabric has potential for use in large area textiles as a heating element in a wide range of applications such as garments, carpets, blankets and automotive seats.

On the origin of the electrical response of vapor grown carbon nanofiber + epoxy composites

Abstract The origin of the electrical response of vapor grown carbon nanofiber (VGCNF) + epoxy composites is investigated by studying the electrical behavior of VGCNF with resin, VGCNF with hardener and cured composites, separately. It is demonstrated that the onset of the conductivity is associated to the emergence of a weak disorder regime. It is also shown that the weak disorder regime is related to a hopping depending on the physical properties of the polymer matrix.