Adriano Sacco

Optimization of 1D ZnO@TiO2 core-shell nanostructures for enhanced photoelectrochemical water splitting under solar light illumination.

A fast and low-cost sol-gel synthesis used to deposit a shell of TiO2 anatase onto an array of vertically aligned ZnO nanowires (NWs) is reported in this paper. The influence of the annealing atmosphere (air or N2) and of the NWs preannealing process, before TiO2 deposition, on both the physicochemical characteristics and photoelectrochemical (PEC) performance of the resulting heterostructure, was studied. The efficient application of the ZnO@TiO2 core-shells for the PEC water-splitting reaction, under simulated solar light illumination (AM 1.5G) solar light illumination in basic media, is here reported for the first time. This application has had a dual function: to enhance the photoactivity of pristine ZnO NWs and to increase the photodegradation stability, because of the protective role of the TiO2 shell. It was found that an air treatment induces a better charge separation and a lower carrier recombination, which in turn are responsible for an improvement in the PEC performance with respect to N2-treated core-shell materials. Finally, a photocurrent of 0.40 mA/cm(2) at 1.23 V versus RHE (2.2 times with respect to the pristine ZnO NWs) was obtained. This achievement can be regarded as a valuable result, considering similar nanostructured electrodes reported in the literature for this application.

A Chemometric Approach for the Sensitization Procedure of ZnO Flowerlike Microstructures for Dye-Sensitized Solar Cells

In this paper, a methodology for the streamlining of the sensitization procedure of flowerlike ZnO nanostructures for dye-sensitized solar cells (DSCs) is reported. The sensitization of ZnO surface with ruthenium-based complexes is a particularly critical process, since one has to minimize the dissolution of surface Zn atoms by the protons released from the dye molecules, leading to the formation of Zn(2+)/dye complexes. The fine-tuning of the experimental parameters, such as the dye loading time, the dye concentration, and the pH of the sensitizing solution, performed through a multivariate optimization by means of a chemometric approach, is here reported. The dye loading procedure was optimized using ZnO microparticles with nanostructured protrusions, synthesized by a simple and low-cost hydrothermal process. Mild reaction conditions were used, and wurtzite-like crystalline structure with a relatively high surface area was obtained once the reaction process was completed. After dispersion of ZnO flowerlike particles in an acetic acid-based solution, a 14 μm-thick ZnO layer acting as DSC photoanode was fabricated. The optimized sensitization procedure allowed minimizing the instability of ZnO surface in contact with acidic dyes, avoiding the formation of molecular agglomerates unable to inject electrons in the ZnO conduction band, achieving good results in the photoconversion efficiency. Moreover, the photoharvesting properties were further enhanced by adding N-methylbenzimidazole into the iodine-based liquid electrolyte. Such an additive was proposed here for the first time in combination with a ZnO photoelectrode, helping to reduce an undesired recombination between the photoinjected electrons and the oxidized redox mediator.

Toward Totally Flexible Dye-Sensitized Solar Cells Based on Titanium Grids and Polymeric Electrolyte

In this work, we present a novelty in the dye-sensitized solar cell scenario: a quasi-solid and completely flexible configuration based on plastic substrates and metallic meshes as support. The aim is to obtain a portable efficient device that can be competitive in the solar market due to the low cost and easy-to-prepare materials used for its fabrication. To fulfill this purpose, three different typologies of devices are proposed and tested in order to move from a rigid to a completely flexible setup in a gradual way. Materials and cells have been thoroughly characterized and tested by means of physicochemical, electrical, and electrochemical measurements to investigate the observed performances and the results that are reported in this paper.

Electrodes/Electrolyte Interfaces in the Presence of a Surface-Modified Photopolymer Electrolyte: Application in Dye-Sensitized Solar Cells

Since hundreds of studies on photoanodes and cathodes show that the electrode/electrolyte interfaces represent a key aspect at the base of dye-sensitized solar cell (DSSC) performances, it is reported here that these interfaces can be managed by a smart design of the spatial composition of quasi-solid electrolytes. By means of a cheap, rapid, and green process of photoinduced polymerization, composition-tailored polymer electrolyte membranes (PEMs) with siloxane-enriched surfaces are prepared, and their properties are thoroughly described. When assembled in DSSCs, the interfacial action promoted by the composition-tailored PEMs enhances the photocurrent and fill factor values, thus increasing the global photovoltaic conversion efficiency with respect to the non-modified PEMs. Moreover, the presence of the siloxane-chain-enriched surface increases the hydrophobicity and reduces the water vapor permeation into the device, thus enhancing the cells durability.

Microwave-Assisted Synthesis of Reduced Graphene Oxide/SnO2 Nanocomposite for Oxygen Reduction Reaction in Microbial Fuel Cells

We report on an easy, fast, eco-friendly, and reliable method for the synthesis of reduced graphene oxide/SnO2 nanocomposite as cathode material for application in microbial fuel cells (MFCs). The material was prepared starting from graphene oxide that has been reduced to graphene during the hydrothermal synthesis of the nanocomposite, carried out in a microwave system. Structural and morphological characterizations evidenced the formation of nanocomposite sheets, with SnO2 crystals of few nanometers integrated in the graphene matrix. Physico-chemical analysis revealed the formation of SnO2 nanoparticles, as well as the functionalization of the graphene by the presence of nitrogen atoms. Electrochemical characterizations put in evidence the ability of such composite to exploit a cocatalysis mechanism for the oxygen reduction reaction, provided by the presence of both SnO2 and nitrogen. In addition, the novel composite catalyst was successfully employed as cathode in seawater-based MFCs, giving electrical performances comparable to those of reference devices employing Pt as catalyst.

Electrochemical and impedance characterization of Microbial Fuel Cells based on 2D and 3D anodic electrodes working with seawater microorganisms under continuous operation.

A mixed microbial population naturally presents in seawater was used as active anodic biofilm of two Microbial Fuel Cells (MFCs), employing either a 2D commercial carbon felt or 3D carbon-coated Berl saddles as anode electrodes, with the aim to compare their electrochemical behavior under continuous operation. After an initial increase of the maximum power density, the felt-based cell reduced its performance at 5 months (from 7 to 4 μW cm(-2)), while the saddle-based MFC exceeds 9 μW cm(-2) (after 2 months) and maintained such performance for all the tests. Electrochemical impedance spectroscopy was used to identify the MFCs controlling losses and indicates that the mass-transport limitations at the biofilm-electrolyte interface have the main contribution (>95%) to their internal resistance. The activation resistance was one order of magnitude lower with the Berl saddles than with carbon felt, suggesting an enhanced charge-transfer in the high surface-area 3D electrode, due to an increase in bacteria population growth.

Nanobranched ZnO Structure: p‐Type Doping Induces Piezoelectric Voltage Generation and Ferroelectric–Photovoltaic Effect

Dr. M. Laurenti, Dr. G. Canavese, Dr. A. Sacco, Dr. M. Fontana, Dr. K. Bejtka, Dr. M. Castellino, Prof. C. F. Pirri, Dr. V. Cauda Center for Space Human Robotics@PoliTo Istituto Italiano di Tecnologia C.so Trento 21 , 10129 Turin , Italy E-mail: valentina.cauda@iit.it Dr. G. Canavese, Dr. M. Fontana, Prof. C. F. Pirri Department of Applied Science and Technology Politecnico di Torino C.so Duca degli Abruzzi 24 , 10129 Turin , Italy

Electric Characterization and Modeling of Microfluidic-Based Dye-Sensitized Solar Cell

The electric response to an external periodic voltage of small amplitude of dye-sensitized solar cells (DSCs) made up with an alternative architecture has been investigated. DSCs have been fabricated with a reversible sealing structure, based on microfluidic concepts, with a precise control on the geometric parameters of the active chamber. Cells with different electrolyte thicknesses have been characterized, without varying the thickness of the TiO2 layer, both under illumination and in dark conditions. Measurements of the electric impedance have been performed in the presence of an external bias ranging from 0 V to 0.8 V. The experimental data have been analyzed in terms of a transmission line model, with two transport channels. The results show that the photovoltaic performances of the microfluidic cell are comparable with those obtained in irreversibly sealed structures, actually demonstrating the reliability of the proposed device.

Impedance spectroscopy analysis of the tunnelling conduction mechanism in piezoresistive composites

The piezoresistive behaviour based on the quantum tunnelling conduction of a copper–polydimethylsiloxane composite was studied by means of impedance spectroscopy and confirmed by the fitting with the tunnelling piezoresistance mathematical model. This investigation paves the way to the implementation of the impedance spectroscopy technique in the characterization of piezoresistive pressure sensors for robotic application.

Monitoring the dye impregnation time of nanostructured photoanodes for dye sensitized solar cells

Dye-sensitized solar cells (DSSCs) are getting increasing attention as low-cost, easy-to-prepare and colored photovoltaic devices. In the current work, in view of optimizing the fabrication procedures and understanding the mechanisms of dye attachment to the semiconductor photoanode, absorbance measurements have been performed at different dye impregnation times ranging from few minutes to 24 hours using UV-Vis spectroscopy. In addition to the traditional absorbance experiments, based on diffuse and specular reflectance on dye impregnated thin films and on the desorption of dye molecules from the photoanodes by means of a basic solution, an alternative in-situ solution depletion measurement, which enables fast and continuous evaluation of dye uptake, is presented. Photoanodes have been prepared with two different nanostructured semiconducting films: mesoporous TiO2, using a commercially available paste from Solaronix, and sponge-like ZnO obtained in our laboratory from sputtering and thermal annealing. Two different dyes have been analyzed: Ruthenizer 535-bisTBA (N719), which is widely used because it gives optimal photovoltaic performances, and a new metal-free organic dye based on a hemisquaraine molecule (CT1). Dye sensitized cells were fabricated using a customized microfluidic architecture. The results of absorbance measurements are presented and discussed in relation to the obtained solar energy conversion efficiencies and the incident photon-to-electron conversion efficiencies (IPCE).