Ahmad Zahran Md Khudzari

A Review of Electrospun Conductive Polyaniline Based Nanofiber Composites and Blends: Processing Features, Applications, and Future Directions

Electrospun polymer nanofibers with high surface area to volume ratio and tunable characteristic are formed through the application of strong electrostatic field. Electrospinning has been identified as a straight forward and viable technique to produce nanofibers from polymer solution as their initial precursor. These nanofiber materials have attracted attention of researchers due to their enhanced and exceptional nanostructural characteristics. Electrospun polyaniline (PANI) based nanofiber is one of the important new materials for the rapidly growing technology development such as nanofiber based sensor devices, conductive tissue engineering scaffold materials, supercapacitors, and flexible solar cells applications. PANI however is relatively hard to process compared to that of other conventional polymers and plastics. The processing of PANI is daunting, mainly due to its rigid backbone which is related to its high level of conjugation. The challenges faced in the electrospinning processing of neat PANI have alternatively led to the development of the electrospun PANI based composites and blends. A review on the research activities of the electrospinning processing of the PANI based nanofibers, the potential prospect in various fields, and their future direction are presented.

Microwave-assisted fibrous decoration of mPE surface utilizing Aloe vera extract for tissue engineering applications.

Developing multifaceted, biocompatible, artificial implants for tissue engineering is a growing field of research. In recent times, several works have been reported about the utilization of biomolecules in combination with synthetic materials to achieve this process. Accordingly, in this study, the ability of an extract obtained from Aloe vera, a commonly used medicinal plant in influencing the biocompatibility of artificial material, is scrutinized using metallocene polyethylene (mPE). The process of coating dense fibrous Aloe vera extract on the surface of mPE was carried out using microwaves. Then, several physicochemical and blood compatibility characterization experiments were performed to disclose the effects of corresponding surface modification. The Fourier transform infrared spectrum showed characteristic vibrations of several active constituents available in Aloe vera and exhibited peak shifts at far infrared regions due to aloe-based mineral deposition. Meanwhile, the contact angle analysis demonstrated a drastic increase in wettability of coated samples, which confirmed the presence of active components on glazed mPE surface. Moreover, the bio-mimic structure of Aloe vera fibers and the influence of microwaves in enhancing the coating characteristics were also meticulously displayed through scanning electron microscopy micrographs and Hirox 3D images. The existence of nanoscale roughness was interpreted through high-resolution profiles obtained from atomic force microscopy. And the extent of variations in irregularities was delineated by measuring average roughness. Aloe vera-induced enrichment in the hemocompatible properties of mPE was established by carrying out in vitro tests such as activated partial thromboplastin time, prothrombin time, platelet adhesion, and hemolysis assay. In conclusion, the Aloe vera-glazed mPE substrate was inferred to attain desirable properties required for multifaceted biomedical implants.

Single-stage electrospun innovative combination of polyurethane and neem oil: Synthesis, characterization and appraisal of blood compatibility

Wound healing is a complex process and it requires proper scaffolding for regeneration. An ideal scaffold should provide optimal environmental conditions in order to assist cellular attachment, proliferation and differentiation. In this work, a new composite based on polyurethane and neem oil was fabricated using one-step electrospinning technique. Fabricated composite patch along with the pristine polyurethane was characterized through scanning electron microscopy, Fourier transform and infrared spectroscopy, thermogravimetric analysis, contact angle measurement and atomic force microscopy. Moreover, the blood compatibility was evaluated using activated partial thromboplastin time, partial thromboplastin time and haemolysis assay. Scanning electron microscopy studies of composites revealed the existence of fibres with a smaller diameter (635  ± 105 nm) compared to the pristine polyurethane (969 ± 217 nm). Fourier transform and infrared analysis revealed the formation of hydrogen bond and peak shifting characteristics confirming the interaction of the neem oil with the polyurethane. Contact angle analysis showed the decrease in contact angle indicating the hydrophilic nature of the fabricated patch compared to pristine polyurethane. Thermal gravimetric analysis depicted the better thermal stability of the novel composite patch due to the existence of neem oil in the pristine polyurethane. The presence of neem oil in polyurethane matrix also resulted in an increase in the surface roughness as observed in the AFM analysis. The novel composite patch showed an ability to reduce the thrombogenicity and promoting the anticoagulant nature signified by blood compatibility assays like activated partial thromboplastin time and partial thromboplastin time. Finally, the haemolytic percentage of the fabricated composite (1%) was found to be reduced compared to control (2.733%) indicating better blood compatibility and safety with the red blood cells. Following the results, the fabricated patches offered enhanced physicochemical and blood compatible nature making it as a promising candidate for wound healing application.

Modification of Aortic Cannula With an Inlet Chamber to Induce Spiral Flow and Improve Outlet Flow: Modification of Aortic Cannula to Induce Spiral Flow

Physiologically, blood ejected from the left ventricle in systole exhibited spiral flow characteristics. This spiral flow has been proven to have several advantages such as lateral reduction of directed forces and thrombus formation, while it also appears to be clinically beneficial in suppressing neurological complications. In order to deliver spiral flow characteristics during cardiopulmonary bypass operation, several modifications have been made on an aortic cannula either at the internal or at the outflow tip; these modifications have proven to yield better hemodynamic performances compared to standard cannula. However, there is no modification done at the inlet part of the aortic cannula for inducing spiral flow so far. This study was carried out by attaching a spiral inducer at the inlet of an aortic cannula. Then, the hemodynamic performances of the new cannula were compared with the standard straight tip end-hole cannula. This is achieved by modeling the cannula and attaching the cannula at a patient-specific aorta model. Numerical approach was utilized to evaluate the hemodynamic performance, and a water jet impact experiment was used to demonstrate the jet force generated by the cannula. The new spiral flow aortic cannula has shown some improvements by reducing approximately 21% of impinging velocity near to the aortic wall, and more than 58% reduction on total force generated as compared to standard cannula.

Flow behaviour in normal and Meniere's disease of endolymphatic fluid inside the inner ear

Menieres disease is a rare disorder that affects the inner ear which might be more severe if not treated. This is due to fluctuating pressure of the fluid in the endolymphatic sac and dysfunction of cochlea which causing the stretching of vestibular membrane. However, the pattern of the flow recirculation in endolymphatic region is still not fully understood. Thus, this study aims to investigate the correlation between the increasing volume of endolymphatic fluid and flow characteristics such as velocity, pressure and wall shear stress. Three dimensional model of simplified endolymphatic region is modeled using computer aided design (CAD) software and simulated using computational fluid dynamic (CFD) software. There are three different models are investigated; normal (N) model, Menieres disease model with less severity (M1) and Menieres disease model with high severity (M2). From the observed, the pressure drop between inlet and outlet of inner ear becomes decreases as the outlet pressure along with endolymphatic volume increases. However, constant flow rate imposed at the inlet of endolymphatic showing the lowest velocity. Flow recirculation near to endolymphatic region is occurred as the volume in endolympathic increases. Overall, high velocity is monitored near to cochlear duct, ductus reuniens and endolymphatic duct. Hence, these areas show high distributions of wall shear stress (WSS) that indicating a high probability of endolymphatic wall membrane dilation. Thus, more severe conditions of Menieres disease, more complex of flow characteristic is occurred. This phenomenon presenting high probability of rupture is predicted at the certain area in the anatomy of vestibular system.

Computational modelling of flow and tip variations of aortic cannulae in cardiopulmonary bypass procedure

Aortic cannulation has been the gold standard for maintaining cardiovascular function during open heart surgery while being connected onto the heart lung machine. These cannulation produces high velocity outflow which may lead to adverse effect on patient condition, especially sandblasting effect on aorta wall and blood cells damage. This paper reports a novel design that was able to decrease high velocity outflow. There were three design factors of that was investigated. The design factors consist of the cannula type, the flow rate, and the cannula tip design which result in 12 variations. The cannulae type used were the spiral flow inducing cannula and the standard cannula. The flow rates are varied from three to five litres per minute (lpm). Parameters for each cannula variation included maximum velocity within the aorta, pressure drop, wall shear stress (WSS) area exceeding 15 Pa, and impinging velocity on the aorta wall were evaluated. Based on the result, spiral flow inducing cannulae is proposed as a better alternatives due to its ability to reduce outflow velocity. Meanwhile, the pressure drop of all variations are less than the limit of 100 mmHg, although standard cannulae yielded better result. All cannulae show low reading of wall shear stress which decrease the possibilities for atherogenesis formation. In conclusion, as far as velocity is concerned, spiral flow is better compared to standard flow across all cannulae variations.

Surface, thermal and hemocompatible properties of novel single stage electrospun nanocomposites comprising polyurethane blended with bio oilTM

In this work, the physicochemical and blood compatibility properties of prepared PU/Bio oil nanocomposites were investigated. Scanning electron microscope (SEM) studies revealed the reduction of mean fiber diameter (709 ± 211 nm) compared to the pristine PU (969 nm ± 217 nm). Fourier transform infrared spectroscopy (FTIR) analysis exposed the characteristic peaks of pristine PU. Composite peak intensities were decreased insinuating the interaction of the bio oilTM with the PU. Contact angle analysis portrayed the hydrophobic nature of the fabricated patch compared to pristine PU. Thermal gravimetric analysis (TGA) depicted the better thermal stability of the novel nanocomposite patch and its different thermal behavior in contrast with the pristine PU. Atomic force microscopy (AFM) analysis revealed the increase in the surface roughness of the composite patch. Activated partial thromboplastin time (APTT) and prothrombin time (PT) signified the novel nanocomposite patch ability in reducing the thrombogenicity and promoting the anticoagulant nature. Finally the hemolytic percentage of the fabricated composite was in the acceptable range revealing its safety and compatibility with the red blood cells. To reinstate, the fabricated patch renders promising physicochemical and blood compatible nature making it a new putative candidate for wound healing application.

Novel Straight Type Aortic Cannula with Spiral Flow Inducing Design

Aortic cannula is one of major factors leading to adverse events such as thrombosis and atherosclerosis development during open heart surgery. This is due to oxygenated blood outflow with high velocity jet from heart lung machine when exiting the cannula tip into ascending aorta. It was discovered, and validated by several researchers that blood flow out of the left ventricle into the aorta is spiral in nature. In this study, a novel design in which internal profile of the cannula was made to induce spiral flow were tested by way of numerical simulation, and compared against existing commercial cannula. Three designs were tested, which differed in number of groove employed. Among the cannula model designs, cannula design with 4 grooves yielded the lowest value of maximum wall shear stress at testing tube with 3.778 Pa and highest value of area weighted helicity density at 40 mm from cannula tips with 11.829 m/s2. Overall, spiral cannula models were showed highly potential in inducing spiral flow, and also the effect on blood hemolysis is acceptable.