Alice Melocchi

Hot-melt extruded filaments based on pharmaceutical grade polymers for 3D printing by fused deposition modeling

Fused deposition modeling (FDM) is a 3D printing technique based on the deposition of successive layers of thermoplastic materials following their softening/melting. Such a technique holds huge potential for the manufacturing of pharmaceutical products and is currently under extensive investigation. Challenges in this field are mainly related to the paucity of adequate filaments composed of pharmaceutical grade materials, which are needed for feeding the FDM equipment. Accordingly, a number of polymers of common use in pharmaceutical formulation were evaluated as starting materials for fabrication via hot melt extrusion of filaments suitable for FDM processes. By using a twin-screw extruder, filaments based on insoluble (ethylcellulose, Eudragit(®) RL), promptly soluble (polyethylene oxide, Kollicoat(®) IR), enteric soluble (Eudragit(®) L, hydroxypropyl methylcellulose acetate succinate) and swellable/erodible (hydrophilic cellulose derivatives, polyvinyl alcohol, Soluplus(®)) polymers were successfully produced, and the possibility of employing them for printing 600μm thick disks was demonstrated. The behavior of disks as barriers when in contact with aqueous fluids was shown consistent with the functional application of the relevant polymeric components. The produced filaments were thus considered potentially suitable for printing capsules and coating layers for immediate or modified release, and, when loaded with active ingredients, any type of dosage forms.

Injection Molding and its application to drug delivery

Injection Molding (IM) consists in the injection, under high pressure conditions, of heat-induced softened materials into a mold cavity where they are shaped. The advantages the technique may offer in the development of drug products concern both production costs (no need for water or other solvents, continuous manufacturing, scalability, patentability) and technological/biopharmaceutical characteristics of the molded items (versatility of the design and composition, possibility of obtaining solid molecular dispersions/solutions of the active ingredient). In this article, process steps and formulation aspects relevant to IM are discussed, with emphasis on the issues and advantages connected with the transfer of this technique from the plastics industry to the production of conventional and controlled-release dosage forms. Moreover, its pharmaceutical applications thus far proposed in the primary literature, intended as either alternative manufacturing strategies for existing products or innovative systems with improved design and performance characteristics, are critically reviewed.

Three-Dimensional Printing of Medicinal Products and the Challenge of Personalized Therapy

By 3-dimensional (3D) printing, solid objects of any shape are fabricated through layer-by-layer addition of materials based on a digital model. At present, such a technique is broadly exploited in many industrial fields because of major advantages in terms of reduced times and costs of development and production. In the biomedical and pharmaceutical domains, the interest in 3D printing is growing in step with the needs of personalized medicine. Printed scaffolds and prostheses have partly replaced medical devices produced by more established techniques, and more recently, 3D printing has been proposed for the manufacturing of drug products. Notably, the availability of patient-tailored pharmaceuticals would be of utmost importance for children, elderly subjects, poor and high metabolizers, and individuals undergoing multiple drug treatments. 3D printing encompasses a range of differing techniques, each involving advantages and open issues. Particularly, solidification of powder, extrusion, and stereolithography have been applied to the manufacturing of drug products. The main challenge to their exploitation for personalized pharmacologic therapy is likely to be related to the regulatory issues involved and to implementation of production models that may allow to efficiently turn the therapeutic needs of individual patients into small batches of appropriate drug products meeting preset quality requirements.

Evaluation of Hot-Melt Extrusion and Injection Molding for Continuous Manufacturing of Immediate-Release Tablets

The exploitation of hot-melt extrusion and injection molding for the manufacturing of immediate-release (IR) tablets was preliminarily investigated in view of their special suitability for continuous manufacturing, which represents a current goal of pharmaceutical production because of its possible advantages in terms of improved sustainability. Tablet-forming agents were initially screened based on processability by single-screw extruder and micromolding machine as well as disintegration/dissolution behavior of extruded/molded prototypes. Various polymers, such as low-viscosity hydroxypropylcellulose, polyvinyl alcohol, polyvinyl alcohol-polyethylene glycol graft copolymer, various sodium starch glycolate grades (e.g., Explotab(®) CLV) that could be processed with no need for technological aids, except for a plasticizer, were identified. Furthermore, the feasibility of both extruded and molded IR tablets from low-viscosity hydroxypropylcellulose or Explotab(®) CLV was assessed. Explotab(®) CLV, in particular, showed thermoplastic properties and a very good aptitude as a tablet-forming agent, starting from which disintegrating tablets were successfully obtained by either techniques. Prototypes containing a poorly soluble model drug (furosemide), based on both a simple formulation (Explotab(®) CLV and water/glycerol as plasticizers) and formulations including dissolution/disintegration adjuvants (soluble and effervescent excipients) were shown to fulfill the USP 37 dissolution requirements for furosemide tablets.

3D printed multi-compartment capsular devices for two-pulse oral drug delivery

&NA; In the drug delivery area, versatile therapeutic systems intended to yield customized combinations of drugs, drug doses and release kinetics have drawn increasing attention, especially because of the advantages that personalized pharmaceutical treatments would offer. In this respect, a previously proposed capsular device able to control the release performance based on its design and composition, which could extemporaneously be filled, was improved to include multiple separate compartments so that differing active ingredients or formulations may be conveyed. The compartments, which may differ in thickness and composition, resulted from assembly of two hollow halves through a joint also acting as a partition. The systems were manufactured by fused deposition modeling (FDM) 3D printing, which holds special potential for product personalization, and injection molding (IM) that would enable production on a larger scale. Through combination of compartments having wall thickness of 600 or 1200 &mgr;m, composed of promptly soluble, swellable/erodible or enteric soluble polymers, devices showing two‐pulse release patterns, consistent with the nature of the starting materials, were obtained. Systems fabricated using the two techniques exhibited comparable performance, thus proving the prototyping ability of FDM versus IM. Graphical abstract Figure. No caption available.

Evaluation of hot-melt extrusion technique in the preparation of HPC matrices for prolonged release.

The aim of the work was to explore the potential of hot-melt extrusion (HME) for preparing hydroxypropyl cellulose (HPC)-based prolonged-release matrices intended for oral administration. For this purpose, compressed and extruded systems, either composed of polymer only or containing different amounts of a model drug (theophylline or ketoprofen), were compared. The overall morphological/physical changes of the systems following interaction with water indicated that the manufacturing process would not exert a major influence on the swelling behavior of the polymeric matrices. On the other hand, the release rate was generally higher from HME systems probably due to an increase of the drug dissolution rate, which is in agreement with the relevant DSC data (loss of drug cristallinity). However, the technological characteristics of the matrices and the maximum drug load were demonstrated to depend on the mode of interaction of the active ingredient with the molten polymer. In this respect, the formation of a composite material from ketoprofen and HPC, when mixed in specific ratios, was supposed to explain the differences observed between compressed and extruded systems in terms of morphological characteristics, hydration/swelling and release. The obtained results support the possibility of exploiting the advantages offered by HME technique, above all the potential for continuous manufacturing, in the preparation of prolonged-release swellable matrices based on a cellulose derivative.

Gastroresistant capsular device prepared by injection molding.

In the present work, the possibility of manufacturing by injection molding (IM) a gastro-resistant capsular device based on hydroxypropyl methyl cellulose acetate succinate (HPMCAS) was investigated. By performing as an enteric soluble container, such a device may provide a basis for the development of advantageous alternatives to coated dosage forms. Preliminarily, the processability of the selected thermoplastic polymer was evaluated, and the need for a plasticizer (polyethylene glycol 1500) in order to counterbalance the glassy nature of the molded items was assessed. However, some critical issues related to the physical/mechanical stability (shrinkage and warpage) and opening time of the device after the pH change were highlighted. Accordingly, an in-depth formulation study was carried out taking into account differing release modifiers potentially useful for enhancing the dissolution/disintegration rate of the capsular device at intestinal pH values. Capsule prototypes with thickness of 600 and 900 μm containing Kollicoat(®) IR and/or Explotab(®) CLV could be manufactured, and a promising performance was achieved with appropriate gastric resistance in pH 1.2 medium and break-up in pH 6.8 within 1h. These results would support the design of a dedicated mold for the development of a scalable manufacturing process.

In vitro and in vivo evaluation of an oral multiple-unit formulation for colonic delivery of insulin

A multiple-unit formulation for time-dependent colonic release of insulin was obtained by coating insulin and sodium glycocholate immediate-release minitablets with: (i) Methocel® E50, a low-viscosity hydroxypropyl methylcellulose (inner coating), (ii) 5:1 w/w Eudragit® NE/Explotab® V17, a mixture of a neutral polymethacrylate with a pore-forming superdisintegrant (intermediate coating), and (iii) Aqoat® AS, enteric-soluble hydroxypropyl methylcellulose acetate succinate (outer coating). Sodium glycocholate was added as a permeation enhancer while the inner, intermediate and outer coatings were aimed, respectively, at delaying the onset of release through swelling/erosion processes, extending the duration of the lag phase by slowing down water penetration into the underlying functional layer, and overcoming variable gastric residence time. In vitro studies showed that neither insulin nor sodium glycocholate were released from the three-layer system during 2h of testing in 0.1N HCl, while complete release of the protein and of the enhancer occurred in phosphate buffer, pH 6.8, after consistent lag phases. No significant changes were noticed in the release profiles following twelve-month storage at 4°C. Oral administration of the novel formulation to diabetic rats elicited a peak in the plasma insulin concentration after 6h, which was associated with a sharp decrease in the glycemic levels. The relative bioavailability and pharmacological availability of such a formulation, as determined vs. the uncoated tablets, were 2.2 and 10.3, respectively. Based on these results, the three-layer system presented was considered a potentially interesting tool for oral colonic delivery of insulin and adjuvant compounds.

Industrial Development of a 3D-Printed Nutraceutical Delivery Platform in the Form of a Multicompartment HPC Capsule

Following recent advances in nutrigenomics and nutrigenetics, as well as in view of the increasing use of nutraceuticals in combination with drug treatments, considerable attention is being directed to the composition, bioefficacy, and release performance of dietary supplements. Moreover, the interest in the possibility of having such products tailored to meet specific needs is fast growing among costumers. To fulfill these emerging market trends, 3D-printed capsular devices originally intended for conveyance and administration of drugs were proposed for delivery of dietary supplements. Being composed of separate inner compartments, such a device could yield customized combinations of substances, relevant doses, and release kinetics. In particular, the aim of this work was to face early-stage industrial development of the processes involved in fabrication of nutraceutical capsules for oral pulsatile delivery. A pilot plant for extrusion of filaments based on pharmaceutical-grade polymers and intended for 3D printing was set up, and studies aimed at demonstrating feasibility of fused deposition modeling in 3D printing of capsule shells according to Current Good Manufacturing Practices for dietary supplements were undertaken. In this respect, the stability of the starting material after hot processing and of the resulting items was investigated, and compliance of elemental and microbiological contaminants, as well as of by-products, with internal specifications was assessed. Finally, operating charts highlighting critical process variables and parameters that would serve as indices of both intermediate and final product quality were developed.

Rheological Characterization of Ethylcellulose-Based Melts for Pharmaceutical Applications

ABSTRACTRheological characterization of ethylcellulose (EC)-based melts intended for the production, via micro-injection moulding (μIM), of oral capsular devices for prolonged release was carried out. Neat EC, plasticized EC and plasticized EC containing solid particles of a release modifier (filler volume content in the melt around 30%) were examined by capillary and rotational rheometry tests. Two release modifiers, differing in both chemical nature and particle geometry, were investigated. When studied by capillary rheometry, neat EC appeared at process temperatures as a highly viscous melt with a shear-thinning characteristic that progressively diminished as the apparent shear rate increased. Thus, EC as such could not successfully be processed via μIM. Plasticization, which induces changes in the material microstructure, enhanced the shear-thinning characteristic of the melt and reduced considerably its elastic properties. Marked wall slip effects were noticed in the capillary flow of the plasticized EC-based melts, with or without release modifier particles. The presence of these particles brought about an increase in viscosity, clearly highlighted by the dynamic experiments at the rotational rheometer. However, it did not impair the material processability. The thermal and rheological study undertaken would turn out a valid guideline for the development of polymeric materials based on pharma-grade polymers with potential for new pharmaceutical applications of μIM.