Alicja Utrata-Wesołek

Poly[tri(ethylene glycol) ethyl ether methacrylate]-coated surfaces for controlled fibroblasts culturing.

Well-defined thermosensitive poly[tri(ethylene glycol) monoethyl ether methacrylate] (P(TEGMA-EE)) brushes were synthesized on a solid substrate by the surface-initiated atom transfer radical polymerization of TEGMA-EE. The polymerization reaction was initiated by 2-bromo-2-methylpropionate groups immobilized on the surface of the wafers. The changes in the surface composition, morphology, philicity, and thickness that occurred at each step of wafer functionalization confirmed that all surface modification procedures were successful. Both the successful modification of the surface and bonding of the P(TEGMA-EE) layer were confirmed by X-ray photoelectron spectroscopy (XPS) measurements. The thickness of the obtained P(TEGMA-EE) layers increased with increasing polymerization time. The increase of environmental temperature above the cloud point temperature of P(TEGMA-EE) caused the changes of surface philicity. A simultaneous decrease in the polymer layer thickness confirmed the thermosensitive properties of these P(TEGMA-EE) layers. The thermosensitive polymer surfaces obtained were evaluated for the growth and harvesting of human fibroblasts (basic skin cells). At 37 °C, seeded cells adhered to and spread well onto the P(TEGMA-EE)-coated surfaces. A confluent cell sheet was formed within 24 h of cell culture. Lowering the temperature to an optimal value of 17.5 °C (below the cloud point temperature of the polymer, TCP, in cell culture medium) led to the separation of the fibroblast sheet from the polymer layer. These promising results indicate that the surfaces produced may successfully be used as substrate for engineering of skin tissue, especially for delivering cell sheets in the treatment of burns and slow-healing wounds.

Controlling the Crystallinity of Thermoresponsive Poly(2-oxazoline)-Based Nanolayers to Cell Adhesion and Detachment

Semicrystalline, thermoresponsive poly(2-isopropyl-2-oxazoline) (PIPOx) layers covalently bonded to glass or silica wafers were obtained via the surface-termination of the living polymer chains. Polymer solutions in acetonitrile were exposed to 50 °C for various time periods and were poured onto the functionalized solid wafers. Fibrillar crystallites formed in polymerization solutions settled down onto the wafers next to the amorphous polymer. The amount of crystallites adsorbed on thermoresponsive polymer layers depended on the annealing time of the PIPOx solution. The wettability of PIPOx layers decreased with the increasing amount of crystallites. The higher content of crystallites weakened the temperature response of the layer, as evidenced by the philicity and thickness measurements. Semicrystalline thermoresponsive PIPOx layers were used as biomaterials for human dermal fibroblasts (HDFs) culture and detachment. The presence of crystallites on the PIPOx layers promoted the proliferation of HDFs. Changes in the physicochemical properties of the layer, caused by the temperature response of the polymer, led to the change in the cells shape from a spindle-like to an ellipsoidal shape, which resulted in their detachment. A supporting membrane was used to assist the detachment of the cells from PIPOx biosurfaces and to prevent the rolling of the sheet.

Transfer of fibroblast sheets cultured on thermoresponsive dishes with membranes

In cell or tissue engineering, it is essential to develop a support for cell-to-cell adhesion, which leads to the generation of cell sheets connected by extracellular matrix. Such supports must be hydrophobic and should result in a detachable cell sheet. A thermoresponsive support that enables the cultured cell sheet to detach using only a change in temperature could be an interesting alternative in regenerative medicine. The aim of this study was to evaluate plates covered with thermoresponsive polymers as supports for the formation of fibroblast sheets and to develop a damage-free procedure for cell sheet transfer with the use of membranes as transfer tools. Human skin fibroblasts were seeded on supports coated with a thermoresponsive polymer: commercial UpCell™ dishes (NUNC™) coated with thermoresponsive poly(N-isopropylacrylamide) (PNIPAM) and dishes coated with thermoresponsive poly(tri(ethylene glycol) monoethyl ether methacrylate) (P(TEGMA-EE)). Confluent fibroblast sheets were effectively cultured and harvested from both commercial PNIPAM-coated dishes and laboratory P(TEGMA-EE)-coated dishes. To transfer a detached cell sheet, two membranes, Immobilon-P® and SUPRATHEL®, were examined. The use of SUPRATHEL for relocating the cell sheets opens a new possibility for the clinical treatment of wounds. This study established the background for implementing thermoresponsive supports for transplanting in vitro cultured fibroblasts.

Thermoresponsive hydrogels of hydrophobically modified polyglycidol

Abstract Synthesis, swelling properties and thermoresponsive behavior of a new class of hydrogels based on high molar mass polyglycidol are presented. High molar mass polyglycidol was synthesized by coordination polymerization. Thermosensitive poly(glycidol-co-glycidyl ethyl carbamate)s were obtained via a simple chemical modification of the polyglycidol with ethyl isocyanate. Polyglycidol and poly(glycidol-co-glycidyl ethyl carbamate)s were chemically crosslinked in DMF solution using oligomeric poly(ethylene glycol)-bis-(carboxymethyl ether chloride) as crosslinking agent. The hydrogels of degree of swelling of over 1000% were obtained. Thermoresponsive properties of the networks and the swellingdeswelling behavior of hydrogels in response to cyclic changes of the temperature were studied.

Photocrosslinking Of Polyglycidol And Its Derivative –Route To Thermoresponsive Hydrogels

Hydrogels of biologically well‐tolerated, high‐molar‐mass polyglycidol (PGl) and its thermoresponsive derivative poly(glycidol‐co‐ethyl glycidyl carbamate) have been obtained by direct UV crosslinking in the solid state. Polymers with molar masses up to 1.45 × 106 g mol−1 were crosslinked in the presence of benzophenone or (4‐benzoylbenzyl)trimethylammonium chloride as photosensitizers. The photosensitizer concentration was varied from 2 to 10 wt%. The influence of polymer composition and photosensitizer type and amount on the crosslinking efficiency, swelling and temperature behavior of the obtained hydrogels was investigated. The photocrosslinking of PGl and poly(glycidol‐co‐ethyl glycidyl carbamate) led to hydrogels with swelling degrees up to 1700%. The swelling degrees of the hydrogels decreased with the increase of the environmental temperature indicating the thermoresponsive nature of gels. The swelling of obtained gels can be controlled by varying the composition of the copolymer precursor and by the network density.