Amitava Roy

High power microwave generation from coaxial virtual cathode oscillator using graphite and velvet cathodes

High power microwave (HPM) generation studies were carried out in KALI-5000 pulse power system. The intense relativistic electron beam was utilized to generate HPMs using a coaxial virtual cathode oscillator. The typical electron beam parameters were 350 kV, 25 kA, and 100 ns, with a few hundreds of ampere per centimeter square current density. Microwaves were generated with graphite and polymer velvet cathode at various diode voltage, current, and accelerating gaps. A horn antenna setup with diode detector and attenuators was used to measure the microwave power. It was observed that the microwave power increases with the diode voltage and current and reduces with the accelerating gap. It was found that both the peak power and width of the microwave pulse is larger for the velvet cathode compared to the graphite cathode. In a coaxial vircator, velvet cathode is superior to the graphite cathode due to its shorter turn on time and better electron beam uniformity.

Characterization and analysis of a pulse power system based on Marx generator and Blumlein.

A pulse power system (1 MV, 50 kA, and 100 ns) based on Marx generator and Blumlein pulse forming line has been studied for characterization of a general system. Total erected Marx inductance and series resistance are calculated from modular testing of Marx generator and testing of Marx generator with Blumlein. The complete pulse power system has been tested with the termination of a liquid resistor load for finding the Blumlein characteristic impedance. Equivalent electrical circuits during the charging and discharging of the Blumlein are constructed from the characterized parameters of the system. These equivalent circuits can be used in the analysis of prepulse voltage and droop in the flat top of the main pulse in the pulse power systems based on Marx generator and Blumlein.

Plasma expansion and fast gap closure in a high power electron beam diode

High power electron beam generation studies were carried out in a planar diode configuration to investigate the effect of the accelerating gap, diode voltage, and anode-cathode materials on the electrode plasma expansion. The diode voltage has been varied from 145–428 kV, whereas the current density has been varied from 208–2215 A/cm2 with 100 ns pulse duration. It was found that the diode voltage and current follow the bipolar space-charge limited flow model. The anode and cathode plasma expansion velocities were calculated using the perveance data. The plasma expands at 11 cm/μs for 34 mm anode-cathode gap and the plasma velocity decreases for smaller gaps. It was found that the plasma expansion velocity increases significantly due to the cathode edge contribution and the edge contribution is particularly important during the beginning and the end of the accelerating pulse when the diode voltage and the corresponding electric field are comparatively low. It was also observed that the diode current incre...

Intense relativistic electron beam generation and prepulse effect in high power cylindrical diode

Intense gigawatt relativistic electron beam has been generated in a high power cylindrical diode in the presence of prepulse. A bipolar prepulse voltage, recorded at the diode, varies both in amplitude and time duration with the Marx generator voltage. It was found that only at the accelerating gap ⩽1.65cm there is some shot to shot variation in the diode voltage and current for the same Marx generator voltage. The anode and cathode plasma expansion velocities were calculated using the perveance data. The plasma expands at 5cm∕μs for 1.85cm radial anode-cathode gap and the plasma velocity decreases for smaller gap. It was found that the effect of the prepulse is less pronounced in the cylindrical diode as compared to planar diode that allows one operation of the cylindrical diode with the gap ⩽1.85cm.

Emission properties of explosive field emission cathodes

The research results of the explosive field emission cathode plasma expansion velocity and the initial emission area in the planar diode configuration with cathodes made of graphite, stainless steel, polymer velvet, carbon coated, and carbon fiber (needle type) cathodes are presented. The experiments have been performed at the electron accelerator LIA-200 (200 kV, 100 ns, and 4 kA). The diode voltage has been varied from 28–225 kV, whereas the current density has been varied from 86–928 A/cm2 with 100 ns pulse duration. The experimentally obtained electron beam diode perveance has been compared with the 1 dimensional Child-Langmuir- law. It was found that initially only a part of the cathode take part in the emission process. The plasma expands at 1.7–5.2 cm/μs for 4 mm anode-cathode gap for various cathode materials. It was found that the plasma expansion velocity increases with the decrease in the cathode diameter. At the beginning of the accelerating pulse, the entire cathode area participates in the e...

Development and Characterization of Repetitive 1-kJ Marx-Generator-Driven Reflex Triode System for High-Power Microwave Generation

This paper presents the design and development of a repetitive Marx generator rated at 1 kJ, 300 kV, 12 kA, and 10 Hz and which is suitable to drive the load directly. Bipolar charging of a Marx generator scheme has been adopted to get the following: 1) faster rise time and 2) relatively low charging voltage. The faster rise time is due to the reduced number of spark gaps down to six for 12 in-series capacitors (0.15 μF and 50 kV) of a six-stage bipolar-charging Marx generator. Interstage inductive charging further enhances the efficiency of the overall system as compared to resistive charging. The generator is characterized by an aqueous resistive load for both polarities at the output voltage. Output voltages of the same magnitude have been achieved for both polarities. The matched impedance is found to be 25 Ω for which a suitable reflex triode is designed. Intense electron beams and high-power microwaves have been generated using this Marx generator and reflex triode system. Experimental results demonstrating the Marx generator and the reflex triode operation are presented and discussed.

Generation and dose distribution measurement of flash x-ray in KALI-5000 system

Summary form only given. The high intensity pulsed electron beam of KALI-5000 system is used to develop a flash X-ray source. The KALI-5000 system is capable of generating intense relativistic electron beam (IREB) of 1MeV, 60 kA and 100 ns when connected to impedance matched electron beam diode. This system is operated in 6 GW, 100 ns duration to produce the Bremsstrahlung flash X-ray on a tantalum target of planner anode-cathode geometry. The axial and the radial dose distribution are characterized using CaSO4: Dy TLDs (thermoluminescent dosimeter) as well as using the optical densitometer to measure the dose distribution of the exposed X-ray film. The measured dose distribution by TLDs and the optical densitometer plus X-ray film matches within plusmn5%.

Extreme ultraviolet emission and confinement of tin plasmas in the presence of a magnetic field

We investigated the role of a guiding magnetic field on extreme ultraviolet (EUV) and ion emission from a laser produced Sn plasma for various laser pulse duration and intensity. For producing plasmas, planar slabs of pure Sn were irradiated with 1064 nm, Nd:YAG laser pulses with varying pulse duration (5–15 ns) and intensity. A magnetic trap was fabricated with the use of two neodymium permanent magnets which provided a magnetic field strength ∼0.5 T along the plume expansion direction. Our results indicate that the EUV conversion efficiency do not depend significantly on applied axial magnetic field. Faraday Cup ion analysis of Sn plasma show that the ion flux reduces by a factor of ∼5 with the application of an axial magnetic field. It was found that the plasma plume expand in the lateral direction with peak velocity measured to be ∼1.2 cm/μs and reduced to ∼0.75 cm/μs with the application of an axial magnetic field. The plume expansion features recorded using fast photography in the presence and absence of 0.5 T axial magnetic field are simulated using particle-in-cell code. Our simulation results qualitatively predict the plasma behavior.

Raman scattering study of LiKSO4—phases II and III

Detailed Raman scattering investigation of LiKSO4 in phases II and III across the transition temperatureTc ≃ 700 K is reported. Abrupt change in frequency and line width of the external and internal modes have been observed. Analysis of the results suggests lithium positional disorder and sulphate orientational disorder in the high temperature phase (II). The results also throw some light on the existence of twin domains in the crystal.

High pressure Raman scattering studies on adamantane

High pressure behavior of adamantane is investigated up to pressures of 26 GPa at ambient temperature using Raman spectroscopy. A detailed study of changes in the Raman spectrum of the C–H stretching modes across the disorder–order transition around 0.5 GPa is reported. Pressure dependence of the internal mode frequencies suggest two more subtle transitions around 2.8 GPa and 8.5 GPa, respectively, which are reversible. Evolution of spectra at higher pressures show evidence for another structural transition above 24 GPa.