Amra Vukovic

Analysis of the Abfraction Lesions Formation Mechanism by the Finite Element Method

Introduction: An abfraction lesion is a type of a non-carious cervical lesion (NCCL) that represents a sharp defect on the cervical part of tooth, caused by occlusal biomechanical forces. The largest prevalence of the NCCL is found on the mandibular first premolar. The goal of the study is, by means of a numerical method – the finite element method (FEM), in an appropriate computer program, conduct a stress analysis of the mandibular premolar under various static loads, with a special reference to the biomechanics of cervical tooth region. Material and methods: A three-dimensional model of the mandibular premolar is gained from a µCT x-ray image. By using the FEM, straining of the enamel, dentin, peridontal ligament and alveolar bone under axial and paraxial forces of 200 [N] is analyzed. The following software were used in the analysis: CT images processing–CTAn program and FEM analysis–AnsysWorkbench 14.0. Results: According to results obtained through the FEM method, the calculated stress is higher with eccentric forces within all tested tooth tissue. The occlusal load leads to a significant stress in the cervical tooth area, especially in the sub-superficial layer of the enamel (over 50 MPa). The measured stress in the peridontal ligament is approximately three times higher under paraxial load with regard to the axial load, while stress calculated in the alveolar bone under paraxial load is almost ten times higher with regard to the axial load. The highest stress values were calculated in the cervical part of the alveoli, where bone resorption is most commonly seen. Conclusion: Action of occlusal forces, especially paraxial ones, leads to significant stress in the cervical part of tooth. The stress values in the cervical sub-superficial enamel layer are almost 5 times higher in relation to the superficial enamel, which additionally confirms complexity of biomechanical processes in the creation of abfraction lesions.

Evaluation of Biocompatibility of Root Canal Sealers on L929 Fibroblasts with Multiscan EX Spectrophotometer.

Introduction: The purpose of the current study was to estimate the biocompatibility of endodontic sealers with different bases on L929 mouse fibroblasts permanent cell line using Multiscan EX Spectrophotometer. Materials and Methods: Endodontics sealers used in this study were GuttaFlow (Roeko) silicone based sealer, AH plus (De Tray-DENTSPLY) epoxy resin based, Apexit (Vivadent) calcium hydroxide based and Endorez (Ultradent) methacrylate based sealer. Sealer were tested trough time, freshly mixed 24 h, 48h and 7 days after setting. Biocompatibility was determinate on permanent cell lines L929 mouse fibroblasts trough cytotoxicity using MTT assay. Level of absorption was measured with multi scan EX spectrophotometer on length 420-600 nm. Results: Sealer based on calcium hydroxide Apexit Plus, GuttaFlow silicone based sealer and AH plus epoxy resin based sealer, have shown a low cytotoxicity through the all periods of time on culture of L292 mouse fibroblasts. Methacrylate based sealer, Endorez showed moderate cytotoxicity when freshly mixed and after 7 days. After 24 hours the visibility of the cells was 74,0% and after 48 hours 65,1%. which is slightly cytotoxic. Conclusions: According to results of this study there is a statistically significant difference among the groups p<0,05 for all the tested sealers. Apexit Plus, GuttaFlow and AH plus can be considered as biocompatibile. EndoREZ sealer which is based on methacrylate, after 7 days shows 50,1% of visible live cells which is considered as moderate cytotoxicity.

Biomechanics of cervical tooth region and noncarious cervical lesions of different morphology; three-dimensional finite element analysis.

Objective: The present study aims to investigate the influence of presence and shape of cervical lesions on biomechanical behavior of mandibular first premolar, subjected to two types of occlusal loading using three-dimensional (3D) finite element method (FEM). Materials and Methods: 3D models of the mandibular premolar are created from a micro computed tomography X-ray image: model of sound mandibular premolar, model with the wedge-shaped cervical lesion (V lesion), and model with saucer-shaped cervical lesion (U lesion). By FEM, straining of the tooth tissues under functional and nonfunctional occlusal loading of 200 (N) is analyzed. For the analysis, the following software was used: CTAn program 1.10 and ANSYS Workbench (version 14.0). The results are presented in von Mises stress. Results: Values of calculated stress in all tooth structures are higher under nonfunctional occlusal loading, while the functional loading is resulted in homogeneous stress distribution. Nonfunctional load in the cervical area of sound tooth model as well as in the sub-superficial layer of the enamel resulted with a significant stress (over 50 [MPa]). The highest stress concentration on models with lesions is noticed on the apex of the V-shaped lesion, while stress in saucer U lesion is significantly lower and distributed over wider area. Conclusion: The type of the occlusal teeth loading has the biggest influence on cervical stress intensity. Geometric shape of the existing lesion is very important in the distribution of internal stress. Compared to the U-shaped lesions, V-shaped lesions show significantly higher stress concentrations under load. Exposure to stress would lead to its progression.

The Correlation between Third Molar Eruptive Stages and Dental Age in Bosnian and Herzegovinian Children and Adolescents

Cleft lip and palate is the most common congenital deformity affecting craniofacial structures. Orofacial clefts have great impact on the quality of life which includes aesthetics, function, psychological impact, dental development and facial growth. Incomplete fusion of facial prominences during the fourth to tenth week of gestation is the main cause. Cleft gaps are closed with alveolar bone grafts in surgical procedure called osteoplasty. Autogenic bone is taken from the iliac crest as the gold standard. The time of grafting can be divided into two stages: primary and secondary. The alveolar defect is usually reconstructured between 7 and 11 years and is often related to the development of the maxillary canine root. After successful osteoplasty, cleft defect is closed but there is still a lack of tooth. The space closure with orthodontic treatment has 50-75% success. If the orthodontic treatment is not possible, in order to replace the missing tooth there are three possibilities: adhesive bridgework, tooth transplantation and implants. Dental implant has the role of holding dental prosthesis, prevents pronounced bone atrophy and loads the augmentation material in the cleft area. Despite the fact that autologous bone from iliac crest is the gold standard, it is not a perfect source for reconstruction of the alveolar cleft. Bone morphogenic protein (BMP) is appropriate as an alternative graft material. The purpose of this review is to explain morphology of cleft defects, historical perspective, surgical techniques and possibilities of implant and prosthodontic rehabilitation.

The clinical survival rate of the FRC inlays prosthetic restorations in the evaluation period of seven years

Aims: In this study, a sample of 28 patients followed the clinical functionality and durability of inlay fiber-reniforced composite (FRC) bridge restorations, laboratory fabricated, for a period of 7 years. Materials and Methods: Patients with the loss of a first molar in the posterior region were selected for the study. Fabrications of FRC structures were made of longitudinal and woven fibers and ceramic optimized polymer material was used for veneering. Statistical Analysis Used: The restorations were evaluated using the modified United States Public Health Service (USPHS) parameters system for the clinical evaluation of dental restorative materials. Kaplan-Meier survival test was used for analyzing the data. Results: During the evaluation period, no fracture of the FRC construction was found. At all tested restorations, significant color change of the Ceromer veneering material was observed. During the investigation time, the color of the restorations became slightly lighter, with loss of gloss. In two patients, a chip off from the veneered material was noticed after 4 years, in three patients over 5 years and in three patients after 6 years. Conclusions: FRC-Ceromer inlay fixed prosthetic restorations for a period of 7 years showed acceptable clinical durability and functionality. Clinical Relevance to Interdisciplinary Dentistry Fiber reinforced composite inlay restorations for a period of seven years showed exceptional durability and functionality with minimal preparation of the abutment teeth. FRC restorations present an acceptable alternative to the classical construction of the metal ceramic or full ceramic bridge which needs to make preparation with extensive reduction of the abutment teeth.