Ana L. Cordeiro

Antifouling potential of Subtilisin A immobilized onto maleic anhydride copolymer thin films

The proteinaceous nature of the adhesives used by most fouling organisms to attach to surfaces suggests that coatings incorporating proteolytic enzymes may provide a technology for the control of biofouling. In the present article, the antifouling (AF) and fouling release potential of model coatings incorporating the surface-immobilized protease, Subtilisin A, have been investigated. The enzyme was covalently attached to maleic anhydride copolymer thin films; the characteristics of the bioactive coatings obtained were adjusted through variation of the type of copolymer and the concentration of the enzyme solution used for immobilization. The bioactive coatings were tested for their effect on the settlement and adhesion strength of two major fouling species: the green alga Ulva linza and the diatom Navicula perminuta. The results show that the immobilized enzyme effectively reduced the settlement and adhesion strength of zoospores of Ulva and the adhesion strength of Navicula cells. The AF efficacy of the bioactive coatings increased with increasing enzyme surface concentration and activity, and was found to be superior to the equivalent amount of enzyme in solution. The results provide a rigorous analysis of one approach to the use of immobilized proteases to reduce the adhesion of marine fouling organisms and are of interest to those investigating enzyme-containing coating technologies for practical biofouling control.

Electrokinetics of Diffuse Soft Interfaces. IV. Analysis of Streaming Current Measurements at Thermoresponsive Thin Films

Streaming current measurements were performed on poly(N-isopropylacrylamide)-co-N-(1-phenylethyl) acrylamide [P(NIPAAm-co-PEAAm)] thermoresponsive thin films above and below the transition temperature of the polymer (i.e., at 22 and 4 degrees C, respectively). Electrokinetic measurements (ionic strength 0.01-10 mM KCl, pH 2.5-9.5 in 1 mM KCl) revealed that the charging of the polymer/aqueous solution interface is determined by unsymmetrical adsorption of hydroxide and hydronium ions onto the Teflon AF substrate that supports the hydrogel film. The magnitude of the streaming current significantly decreased with decreasing temperature, that is, when the hydrogel was swelling. The pH- and ionic strength-dependent data for unswollen and swollen films were interpreted on the basis of the here-reported general theory for the electrokinetics of diffuse soft gel layers. The formalism based on the Debye-Brinkman equation for hydrodynamics and the nonlinear Poisson-Boltzmann equation for electrostatics extends previous theoretical studies by considering the most general situation of a charged gel layer supported by a charged rigid surface. Full analytical expression is provided for the streaming current in the limit of homogeneous distribution of segments under low potential conditions. Numerical analysis of the governing transport and electrostatic equations allows for the computation of streaming current for cases where analytical developments are not possible. The theory successfully reproduces the electrokinetic data for the P(NIPAAm-co-PEAAm) copolymer film at 22 and 4 degrees C over the whole range of pH and ionic strength examined. It is found that the 3-fold increase of the hydrogel film thickness with decreasing temperature from 22 to 4 degrees C (i.e., from 23 to 70 nm as measured by ellipsometry), is in line with homogeneous swelling and an increase of the hydrodynamic penetration length (1/lambdao) by a factor of approximately 1.6. Additionally, the hydrodynamic thicknesses (deltaH) of the swollen and unswollen hydrogels are evaluated in terms of their respective hydrodynamic penetration length and electrosurface characteristics of the supporting Teflon AF surface.

Temperature dependent physicochemical properties of poly(N-isopropylacrylamide-co-N-(1-phenylethyl) acrylamide) thin films

The physicochemical properties of thermo-responsive polymer films are dynamically altered upon changes in environmental conditions. We report on the design and detailed characterization of a novel thermo-responsive polymer film with a temperature transition tuned to fit applications related to the control of marine biofouling. A copolymer consisting of poly(N-isopropylacrylamide) (PNIPAAm) and N-(1-phenylethyl) acrylamide (PEAAm) was synthesized and immobilized as a thin film onto Teflon AF surfaces using a low pressure argon plasma treatment. The temperature dependent physicochemical properties of the thermo-responsive film were thoroughly characterized and the impact of sea water on the film properties was investigated. The immobilized thermo-responsive film exhibits a reversible swelling/deswelling with temperature. Atomic force microscopy showed no morphological changes with varying temperature. Streaming current measurements performed above and below the transition temperature of the thermo-responsive hydrogel indicated that the charging of the polymer/aqueous solution interface is mainly determined by the preferential water ion adsorption at the Teflon AF surface. Inverse contact angles measured using captive air bubbles and analysed by axisymmetric drop shape analysis (ADSA) supported the intrinsic properties of the thermo-responsive film, as surface hydrophilicity decreased with increasing temperature. The advancing water contact angle decreased with increasing temperature, which may be explained by the different molecular mobility at different temperatures, allowing or hampering the re-orientation of hydrophobic segments at the solid–liquid and solid–fluid interfaces. These new films will allow investigations on the interaction of microorganisms with environmentally sensitive surfaces.

Covalent Immobilization of Subtilisin A onto Thin Films of Maleic Anhydride Copolymers

Enzymes cleaving the biopolymer adhesives of fouling organisms are attracting attention for the prevention of biofouling. We report a versatile and robust method to confine the serine protease Subtilisin A (or Subtilisin Carlsberg) to surfaces to be protected against biofouling. The approach consists of the covalent immobilization of the protease onto maleic anhydride copolymer thin film coatings. High-swelling poly(ethylene-alt-maleic anhydride) (PEMA) copolymer layers permitted significantly higher enzyme loadings and activities than compact poly(octadecene-alt-maleic anhydride) (POMA) films. Substantial fractions of the immobilized, active enzyme layers were found to be conserved upon storage in deionized water for several hours. Ongoing studies explore the potentialities of the developed bioactive coatings to reduce the adhesion of various fouling organisms.

Immobilization of Bacillus licheniformis α-amylase onto reactive polymer films

Alpha-amylase was covalently immobilized onto maleic anhydride copolymer films preserving activity. The initial activity of the immobilized layers strongly depended on the immobilization solution, and on the physicochemical properties of the copolymer film. Higher enzyme loading (quantified by amino acid analysis using HPLC) and activity (measured by following starch hydrolysis) were attainable onto hydrophilic, highly swelling 3-D poly(ethylene-alt-maleic anhydride) (PEMA) copolymer films, while immobilization onto hydrophobic poly(octadecene-alt-maleic anhydride) (POMA) copolymer films resulted in low content enzyme layers and lower activity. No significant activity was lost upon dehydration/re-hydration or storage of enzyme containing PEMA copolymer layers in deionised water for up to 48 h. In contrast, α-amylase decorated POMA films suffered a significant activity loss under those conditions. The distinct behaviours may be attributed to the different intrinsic physicochemical properties of the copolymer films. The compact, hydrophobic POMA films possibly favours hydrophobic interactions between the hydrophobic moieties of the protein and the surface, which may result in conformational changes, and consequent loss of activity. Surprisingly, residual activity was found after harsh treatments of active α-amylase PEMA based layers revealing that immobilization onto the hydrophilic polymer films improved the stability of the enzyme.

Functionalization of Poly(dimethylsiloxane) Surfaces with Maleic Anhydride Copolymer Films

Combining advantageous bulk properties of polymeric materials with surface-selective chemical conversions is required in numerous advanced technologies. For that aim, we investigate strategies to graft maleic anhydride (MA) copolymer films onto poly(dimethylsiloxane) (PDMS) precoatings. Amino groups allowing the covalent attachment of the MA copolymer films to the PDMS (Sylgard 184) surface were introduced either by low-pressure ammonia plasma treatment, or by attachment of 3-aminopropyltriethoxysilane (APTES) onto air plasma-treated PDMS. The resultant coatings were extensively characterized by X-ray photoelectron spectroscopy (XPS), attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), contact angle measurements, and atomic force microscopy (AFM). The results show that the impact of the plasma treatment on the physical properties on the topmost surface of the PDMS is critically important for the characteristics of the layered coatings.

Immobilized enzymes affect biofilm formation

The effect of the activity of immobilized enzymes on the initial attachment of pathogenic bacteria commonly associated with nosocomial infections (Pseudomonas aeruginosa and Staphylococcus epidermidis) was investigated. The proteolytic enzymes, subtilisin A and the glycoside hydrolase cellulose, were covalently attached onto poly(ethylene-alt-maleic) anhydride copolymer films. A comparison between active and heat-inactivated surfaces showed that while the activity of immobilized cellulase reduced the attachment of S. epidermidis by 67%, it had no effect on the attachment of P. aeruginosa. Immobilized subtilisin A had opposite effects: the active enzyme had no effect on the attachment of S. epidermidis but reduced the attachment of P. aeruginosa by 44%. The results suggest that different biomolecules are involved in the initial steps of attachment of different bacteria, and that the development of broad-spectrum antifouling enzymatic coatings will need to involve the co-immobilization of enzymes.

Enzyme immobilization on reactive polymer films.

Immobilized enzymes are currently used in many bioanalytical and biomedical applications. This protocol describes the use of thin films of maleic anhydride copolymers to covalently attach enzymes directly to solid supports at defined concentrations. The concentration and activity of the surface-bound enzymes can be tuned over a wide range by adjusting the concentration of enzyme used for immobilization and the physicochemical properties of the polymer platform, as demonstrated here for the proteolytic enzyme Subtilisin A. The versatile method presented allows for the immobilization of biomolecules containing primary amino groups to a broad variety of solid carriers, ranging from silicon oxide surfaces to standard polystyrene well plates and metallic surfaces. The approach can be used to investigate the effects of immobilized enzymes on cell adhesion, and on the catalysis of specific reactions.

Controlling the adhesion of the diatom Navicula perminuta using poly(N-isopropylacrylamide-co-N-(1-phenylethyl) acrylamide) films.

Poly(N-isopropylacrylamide)-co–N-(1-phenylethyl) acrylamide [P(NIPAAm-co-PEAAm)] thermo-responsive thin films with a lower critical solution temperature (LCST) adjusted to fit marine applications were used to investigate the effect of changes in the wetting properties of a surface on the adhesion of the diatom Navicula perminuta, an organism which forms slime films on surfaces immersed in an aquatic environment. Although the strength of attachment of cells was affected by whether the film was collapsed or expanded, no significant decrease in adhesion strength occurred upon temperature decrease. The effects were attributed to possible strong interactions between the hydrophobic segments of the responsive film when collapsed with components in the adhesive complex.