Anatol Krozer

Characterization of QCM sensor surfaces coated with molecularly imprinted nanoparticles

Molecularly imprinted polymers (MIPs) are gaining great interest as tailor-made recognition materials for the development of biomimetic sensors. Various approaches have been adopted to interface MIPs with different transducers, including the use of pre-made imprinted particles and the in situ preparation of thin polymer layers directly on transducer surfaces. In this work we functionalized quartz crystal microbalance (QCM) sensor crystals by coating the sensing surfaces with pre-made molecularly imprinted nanoparticles. The nanoparticles were immobilized on the QCM transducers by physical entrapment in a thin poly(ethylene terephthalate) (PET) layer that was spin-coated on the transducer surface. By controlling the deposition conditions, it was possible to gain a high nanoparticle loading in a stable PET layer, allowing the recognition sites in nanoparticles to be easily accessed by the test analytes. In this work, different sensor surfaces were studied by micro-profilometry and atomic force microscopy and the functionality was evaluated using quartz crystal microbalance with dissipation (QCM-D). The molecular recognition capability of the sensors were also confirmed using radioligand binding analysis by testing their response to the presence of the test compounds, (R)- and (S)-propranolol in aqueous buffer.

Tailored Magnetic Nanoparticles for Direct and Sensitive Detection of Biomolecules in Biological Samples

We developed nanoparticles with tailored magnetic properties for direct and sensitive detection of biomolecules in biological samples in a single step. Thermally blocked nanoparticles obtained by thermal hydrolysis, functionalized with specific ligands, are mixed with sample solutions, and the variation of the magnetic relaxation due to surface binding is used to detect the presence of biomolecules. The binding significantly increases the hydrodynamic volume of nanoparticles, thus changing their Brownian relaxation frequency which is measured by a specifically developed AC susceptometer. The system was tested for the presence of Brucella antibodies, a dangerous pathogen causing brucellosis with severe effects both on humans and animals, in serum samples from infected cows and the surface of the nanoparticles was functionalized with lipopolysaccharides (LPS) from Brucella abortus. The hydrodynamic volume of LPS-functionalized particles increased by 25-35% as a result of the binding of the antibodies, measured by changes in the susceptibility in an alternating magnetic field. The method has shown high sensitivity, with detection limit of 0.05 microg x mL(-1) of antibody in the biological samples without any pretreatment. This magnetic-based assay is very sensitive, cost-efficient, and versatile, giving a direct indication whether the animal is infected or not, making it suitable for point-of-care applications. The functionalization of tailored magnetic nanoparticles can be modified to suit numerous homogeneous assays for a wide range of applications.

QCM-D analysis of the performance of blocking agents on gold and polystyrene surfaces.

With todays developments of biosensors and medical implants comes the need for efficient reduction of nonspecific binding. We report on a comparison of the ability of traditionally used blocking agents and poly(ethylene glycol) (PEG) derivatives to prevent protein adsorption on both gold and polystyrene surfaces. The adsorption kinetics of blocking molecules and proteins was monitored gravimetrically using quartz crystal microbalance with dissipation (QCM-D). The resistance to nonspecific adsorption was evaluated on gold and polystyrene surfaces coated with bovine serum albumin (BSA) or casein, gold coated with three different 6-11 ethylene glycol (EG) long hydroxyl- or methoxy-terminated PEG-thiolates and polystyrene blocked with a PLL-g-PEG or three different 12 EG long benzyl-PEG-derivatives. The prevention of protein adsorption on the coated surfaces was evaluated by monitoring the mass uptake at the addition of both pure prostate specific antigen (PSA) and seminal plasma. We demonstrate that on pure gold the PEG-thiols are superior to the other blocking molecules tested, with the end group and length of the PEG-thiols used being of minor importance. On polystyrene surfaces blocking with PLL-g-PEG, BSA and casein gave the best results. These results have an impact on further development of an optimized immunoassay protocol.

Motion of nanometer sized magnetic particles in a magnetic field gradient

Using magnetic particles with sizes in the nanometer range in biomedical magnetic separation has gained much interest recently due to their higher surface area to particle volume and lower sedimentation rates. In this paper, we report our both theoretical and experimental investigation of the motion of magnetic particles in a magnetic field gradient with particle sizes from 425 nm down to 50 nm. In the experimental measurements, we monitor the absorbance change of the sample volume as the particle concentration varies over time. We also implement a Brownian dynamics algorithm to investigate the influence of particle interactions during the separation and compare it to the experimental results for validation. The simulation agrees well with the measurements for particle sizes around 425 nm. Some discrepancies remain for smaller particle sizes, which may indicate that additional factors also influence the separation for the smaller size range. We observe that the separation process includes the formation of...

Towards an electrowetting-based digital microfluidic platform for magnetic immunoassays

We demonstrate ElectroWetting-On-Dielectric (EWOD) transport and SQUID gradiometer detection of magnetic nanoparticles (MNPs) suspended in a 2 microl de-ionized water droplet. This proof-of-concept methodology constitutes the first development step towards a highly sensitive magnetic immunoassay platform with SQUID readout and droplet-based sample handling. Magnetic AC-susceptibility measurements were performed on MNPs with a hydrodynamic diameter of 100 nm using a high-Tc dc Superconducting Quantum Interference Device (SQUID) gradiometer as detector. We observed that the signal amplitude per unit volume is 2.5 times higher for a 2 microl sample droplet compared to a 30 microl sample volume.

Smart Electrochemical Oxygen Sensor for Personal Protective Equipment

Self contained closed circuit rebreathers are life supporting breathing systems, where the exhaled gas is recycled by filtering CO2 and replacing metabolized O2. For the O2 injection control galvanic O2 sensors are used to measure the partial pressure of O2. A malfunction of the sensors can lead to a gas mixture beyond life supporting limits which is life threatening. Galvanic O2 sensors are often used in anaesthetic machines in hospitals. Also in this case, a malfunction of the sensors can cause severe injury to a person. It is obvious that such sensors are key elements in life supporting equipment and as such must be designed in order to achieve high functional safety. However these sensors are consuming sensors, and with that, will fail at a certain time. Failure modes include current limitation, non linearity, electrolyte evaporation or leakage, etc. Within this paper a novel low cost read out electronic circuit for galvanic O2 sensors is presented, which allows not only digital readout, digital temperature compensation, on board storage of calibration and manufacturing data, but also can be used for performing voltammetry cycles to test the Pb anode for exhaustion. First measurements are presented and compared to data from a Solartron SI 1287 impedance analyzer, which is state-of-the-art in electrochemical sensor characterization.

Characterization of molecularly imprinted polymer nanoparticles by photon correlation spectroscopy

We follow template‐binding induced aggregation of nanoparticles enantioselectively imprinted against (S)‐propranolol, and the non‐imprinted ones, using photon correlation spectroscopy (dynamic light scattering). The method requires no separation steps. We have characterized binding of (R,S)‐propranolol to the imprinted polymers and determined the degree of non‐specificity by comparing the specific binding with the results obtained using non‐imprinted nanoparticles. Using (S)‐propranolol as a template for binding to (S)‐imprinted nanoparticle, and (R)‐propranolol as a non‐specific control, we have determined range of concentrations where chiral recognition can be observed. By studying aggregation induced by three analytes related to propranolol, atenolol, betaxolol, and 1‐amino‐3‐(naphthalen‐1‐yloxy)propan‐2‐ol, we were able to determine which parts of the template are involved in the specific binding, discuss several details of specific adsorption, and the structure of the imprinted site. Copyright

Characterization of Molecularly Imprinted Polymers as Novel Materials for Biochemical Sensors

Abstract We study the behavior of Molecularly Imprinted Polymers (MIP) as novel synthetic receptor layers in biochemical sensors. Electropolymerization was used as an easy to implement method for polymer deposition and integrated impedance spectroscopy to monitor MIP behavior towards target molecules. Contrary to what is reported in the literature we consider that it is neither easy nor reliable to attribute the impedance changes to target binding/elution. However, alternative and/or more precise characterization methods are needed to track nano-scale changes in MIPs. Thus we are developing an optical set-up for detection of static deflections on the micro-cantilevers as a result of surface stress induced by changes in MIPs. Using an optical set-up, changes in the deflection of MIP-covered micro-cantilevers when exposed to the target molecules could be measured.