Andrea Terenzi

Polypropylene-natural fibre composites. Analysis of fibre structure modification during compounding and its influence on the final properties

The final properties of composite materials are highly dependent on the residual geometrical parameters (length, diameter, aspect ratio), orientation and distribution of the fibres in the matrix, which in turn are related to the processing conditions. This study analysed the fibre structure variation during the processing of a polypropylene matrix reinforced with cellulose flax pulp for different reinforcement concentrations. The fibres geometrical parameters, length, diameter and aspect ratio have been measured and their statistical distributions have been assessed for each concentration. Furthermore, the effect of the microstructure variation on the final mechanical properties was analysed. In particular, changes in the interfacial area were evaluated based on the hypothesis that the fibres were cylindrical in shape and considering the average values of the diameters and the lengths calculated using a statistical distribution approach. The fibre interfacial area after the process decreases as the fibre concentration increases and this evaluation explains how the adhesion methods that are used for fibre surface modification fail because of the decrement in the modifier interfacial density. The Halpin–Tsai approach was used to model the experimental data obtained from tensile tests for different composites, so as to confirm the effect of fibre parameters, such as aspect ratio and interfacial area values, in the PP/cellulose blends final properties.

Ternary PVA nanocomposites containing cellulose nanocrystals from different sources and silver particles: part II.

Cellulose nanocrystals (CNC) extracted from three different sources, namely flax, phormium, and commercial microcrystalline cellulose (MCC) have been used in a polyvinyl alcohol (PVA) matrix to produce anti-bacterial films using two different amounts of silver nanoparticles (0.1 wt% and 0.5 wt%). In general, CNC confer an effect of reinforcement to PVA film, the best values of stiffness being offered by composites produced using phormium fibres, whilst for strength those produced using flax are slightly superior. This was obtained without inducing any particular modification in transition temperatures and in the thermal degradation patterns. As regards antibacterial properties, systems with CNC from flax proved slightly better than those with CNC from phormium and substantially better than those including commercial MCC. Dynamic mechanical thermal analysis (DMTA) has only been performed on the ternary composite containing 0.1 wt% Ag, which yielded higher values of Youngs modulus, and as a whole confirmed the above results.

Processing Conditions, Thermal and Mechanical Responses of Stretchable Poly (Lactic Acid)/Poly (Butylene Succinate) Films

Poly (lactic acid) (PLA) and poly (butylene succinate) (PBS) based films containing two different plasticizers [Acetyl Tributyl Citrate (ATBC) and isosorbide diester (ISE)] at three different contents (15 wt %, 20 wt % and 30 wt %) were produced by extrusion method. Thermal, morphological, mechanical and wettability behavior of produced materials was investigated as a function of plasticizer content. Filmature parameters were also adjusted and optimized for different formulations, in order to obtain similar thickness for different systems. Differential scanning calorimeter (DSC) results and evaluation of solubility parameter confirmed that similar miscibility was obtained for ATBC and ISE in PLA, while the two selected plasticizers resulted as not efficient for plasticization of PBS, to the limit that the PBS–30ATBC resulted as not processable. On the basis of these results, isosorbide-based plasticizer was considered a suitable agent for modification of a selected blend (PLA/PBS 80:20) and two mixing approaches were used to identify the role of ISE in the plasticization process: results from mechanical analysis confirmed that both produced PLA–PBS blends (PLA85–ISE15)–PBS20 and (PLA80–PBS20)–ISE15 could guarantee advantages in terms of deformability, with respect to the PLA80–PBS20 reference film, suggesting that the promising use of these stretchable PLA–PBS based films plasticized with isosorbide can provide novel solutions for food packaging applications.

Glass optical fibre sensors for detection of through thickness moisture diffusion in glass reinforced composites under hostile environments

A combination of evanescent wave optical sensors (EWOSs) and fibre Bragg gratings (FBGs) were embedded in an epoxy vinyl ester and an epoxy vinyl ester based glass reinforced polymer (GRP) composite to measure fluid ingress that would result in degradation under hostile conditions. Samples were subjected to accelerated aging in the form of single sided exposure to simulated sea water at 120°C in a pressurised stainless steel vessel. Low cost EWOSs were prepared from a standard multimode glass optical fibre and compared to commercially available FBGs. Both sensors were able to detect the early stage of moisture diffusion into the GRP matrix. The evanescent sensors showed a reduction in the transmitted signal intensity between 1500 and 1650 nm with an increasing exposure time due to a change in the optical properties of the polymer, whereas a peak shift was observed for the FBGs due to the swelling of the resin with the absorption of water. Additionally, the glass optical fibre sensors were embedded in a configuration that allowed the extent of diffusion through the thickness of the GRPs to be monitored, with the fibres in the closest position to the exposure face showing a greater signal change than those positioned further away.

Processing and Characterization of Nano-biocomposites Based on Mater-Bi® with Layered Silicates

The development of new nano-biocomposites has been one of the main research areas of interest in polymer science in recent years, since they can combine the intrinsic biodegradable nature of matrices with the ability to modify their properties by the addition of selected nano-reinforcements. In this work, the addition of mineral nanoclays (montmorillonites and sepiolites) to a commercial starch-based matrix is proposed. A complete study on their processing by melt-intercalation techniques and further evaluation of the main properties of nano-biocomposites has been carried out. The results reported show an important infl uence of the nano-biocomposites morphology on their fi nal properties. In particular, the rheological and viscoelastic characteristics of these systems are very sensitive to the dispersion level of the nanofi ller, but it is possible to assess that the material processing behaviour is not compromised by the presence of these nano-reinforcements. In general, both nanofi llers had a positive infl uence in the materials fi nal properties. Mechanical performance shows improvements in terms of elastic modulus, without important limitations in terms of ductility. Thermal properties are improved in terms of residual mass after degradation and low improvements are also observed in terms of oxygen barrier properties. ® , nanoclays, melt intercalation, characterisation

Epoxy–carbon nanotube composites

Abstract: The primary current objective is to develop knowledge-based technologies of carbon nanotubes (CNTs), understanding the surface chemistry and processing tools used in designing polymer-based composites. The chapter emphasizes the different functionalization processes and the parameters affecting the nanotube dispersability in polymeric matrices. We also describe different processing methods for incorporating such functional nanofillers into the polymer backbone. How functionalized carbon nanotubes can improve the thermal, mechanical and electrical properties of common epoxy matrices already used in advanced applications is also reported. Moreover, the chapter reviews the different chemorheological approaches adopted to describe the catalytic effects of pristine and functionalized CNTs on the curing of epoxy systems through the development and application of coupled kinetic and rheological models. Finally, the effects of functionalized CNTs on the thermal, electric and mechanical properties are reviewed and explained in terms of the interactions between the functionalized CNTs and typical epoxy resins used in advanced applications.