Andrea Zocca

3D-printed silicate porous bioceramics using a non-sacrificial preceramic polymer binder

Silicate bioceramics possess an excellent bioactivity; however, shaping them into complex geometries is still challenging. Therefore, this paper aims to present a new strategy for the shaping of a bioglass-ceramic with controlled geometry and properties starting from a glass powder combined with a preceramic polymer, i.e. a silicon resin, and reactive fillers. The powder-based three-dimensional (3D)-printing of wollastonite (CaSiO3)-based silicate bioceramic parts was demonstrated in this work. The resin plays a dual role, as it not only acts as a non-sacrificial binder for the filler powders in the printing process but it also reacts with the fillers to generate the desired bioceramic phases. The mechanical and physical properties, i.e. ball-on-three-balls test, density, porosity and morphology, were evaluated in 3D-printed discs. These samples possessed a total porosity around 64 vol% and a biaxial flexural strength around 6 MPa. The raw materials used in this work also enabled the 3D-printing of scaffolds possessing a designed multi-scale porosity, suitable bioceramic phase assemblage and a compressive strength of 1 MPa (for cylindrical scaffolds with total porosity ~80 vol%). Solubility in TRIS/HCl and in vitro assays, i.e. viability, cytotoxicity and apoptosis assays, were also performed. In vitro tests indicated good cell viability and no cytotoxicity effect on the cells.

Powder-Bed Stabilization for Powder-Based Additive Manufacturing

The most successful additive manufacturing (AM) technologies are based on thelayer-by-layer depositionof a flowable powder. Although considered as the third industrial revolution, one factor still limiting these processes to become completely autonomous is the often necessary build-up of support structures. Besides the prevention of lateral shifts of the part during the deposition of layers, the support assures quality and stability to the built process. The loose powder itself surrounding the built object, or so-called powder-bed, does not provide this sustenance in most existent technology available. Here we present a simple but effective and economical method for stabilizing the powder-bed, preventing distortions in the geometry with no need for support structures. This effect, achieved by applying an air flow through the powder-bed, is enabling an entirely autonomous generation of parts and is a major contribution to all powder-based additive manufacturing technologies. Moreover, it makes powder-based AM independent of gravitational forces, which will facilitate crafting items in space from a variety of powdery materials.

Towards the colonization of Mars by in-situ resource utilization: Slip cast ceramics from Martian soil simulant

Here we demonstrate that by applying exclusively Martian resources a processing route involving suspensions of mineral particles called slurries or slips can be established for manufacturing ceramics on Mars. We developed water-based slurries without the use of additives that had a 51 wt. % solid load resembling commercial porcelain slurries in respect to the particle size distribution and rheological properties. These slurries were used to slip cast discs, rings and vases that were sintered at temperatures between 1000 and 1130 °C using different sintering schedules, the latter were set-up according the results of hot-stage microscopic characterization. The microstructure, porosity and the mechanical properties were characterized by SEM, X-ray computer tomography and Weibull analysis. Our wet processing of minerals yields ceramics with complex shapes that show similar mechanical properties to porcelain and could serve as a technology for future Mars colonization. The best quality parts with completely vitrificated matrix supporting a few idiomorphic crystals are obtained at 1130 °C with 10 h dwell time with volume and linear shrinkage as much as ~62% and ~17% and a characteristic compressive strength of 51 MPa.

Structural optimization of printed structures by self-organized relaxation

Purpose This paper aims to present an additive manufacturing-based approach in which a new strategy for a thermally activated local melting and material flow, which results in densification of printed structures, is introduced. Design/methodology/approach For enabling this self-organized relaxation of printed objects by the viscous flow of material, two interconnected structures are printed simultaneously in one printing process, namely, Structure A actually representing the three dimensional object to be built and Structure B acting as a material reservoir for infiltrating Structure A. In an additional process step, subsequent to the printing job, an increase in the objects’ temperature results in the melting of the material reservoir B and infiltration of structure A. Findings A thermally activated local melting of the polymethylsilsesquioxane results in densification of the printed structures and the local formation of structures with minimum surface area. Originality/value The present work introduces an approach for the local relaxation of printed three-dimensional structures by the viscous flow of the printed material, without the loss of structural integrity of the structure itself. This approach is not restricted only to the materials used, but also offers a more general strategy for printing dense structures with a surface finish far beyond the volumetric resolution of the 3D printing process.