Andrew E. Dane

On-chip detection of non-classical light by scalable integration of single-photon detectors

Photonic-integrated circuits have emerged as a scalable platform for complex quantum systems. A central goal is to integrate single-photon detectors to reduce optical losses, latency and wiring complexity associated with off-chip detectors. Superconducting nanowire single-photon detectors (SNSPDs) are particularly attractive because of high detection efficiency, sub-50-ps jitter and nanosecond-scale reset time. However, while single detectors have been incorporated into individual waveguides, the system detection efficiency of multiple SNSPDs in one photonic circuit—required for scalable quantum photonic circuits—has been limited to <0.2%. Here we introduce a micrometer-scale flip-chip process that enables scalable integration of SNSPDs on a range of photonic circuits. Ten low-jitter detectors are integrated on one circuit with 100% device yield. With an average system detection efficiency beyond 10%, and estimated on-chip detection efficiency of 14–52% for four detectors operated simultaneously, we demonstrate, to the best of our knowledge, the first on-chip photon correlation measurements of non-classical light.

Fabrication Process Yielding Saturated Nanowire Single-Photon Detectors With 24-ps Jitter

We present an optimized fabrication process for superconducting nanowire single-photon detectors that allowed us to obtain a yield of ~70% for detectors based on 80-nm-wide niobium nitride nanowires. We fabricated detectors that showed 24-ps timing jitter and saturated detection efficiency without the need for cryogenic amplifiers, allowing for operation in a low-bias low-dark-count-rate regime while operating at maximum detection efficiency.

Superconducting nanowire detector jitter limited by detector geometry

Detection jitter quantifies variance introduced by the detector in the determination of photon arrival time. It is a crucial performance parameter for systems using superconducting nanowire single photon detectors (SNSPDs). In this work, we have demonstrated that the detection timing jitter is limited in part by the spatial variation of the photon detection events along the length of the wire. We define this jitter source as a geometric jitter since it is related to the length and area of the SNSPD. To characterize the geometric jitter, we have constructed a differential cryogenic readout with less than 7 ps of an electronic jitter that can amplify the pulses generated from the two ends of an SNSPD. By differencing the measured arrival times of the two electrical pulses, we were able to partially cancel out the difference of the propagation times and thus reduce the uncertainty of the photon arrival time. We proved that the variation of the differential propagation time was a few ps for a 3 μm × 3 μm devi...

Single-photon imager based on a superconducting nanowire delay line

Detecting spatial and temporal information of individual photons by using singlephoton-detector (SPD) arrays is critical to applications in spectroscopy, communication, biological imaging, astronomical observation, and quantum-information processing. Among the current SPDs, detectors based on superconducting nanowires have outstanding performance, but are limited in their ability to be integrated into large scale arrays due to the engineering difficulty of high-bandwidth cryogenic electronic readout. Here, we address this problem by demonstrating a scalable single-photon imager using a single continuous photon-sensitive superconducting nanowire microwave-plasmon transmission line. By appropriately designing the nanowire’s local electromagnetic environment so that the nanowire guides microwave plasmons, the propagating voltages signals generated by a photon-detection event were slowed down to ~ 2% of the speed of light. As a result, the time difference between arrivals of the signals at the two

Eight-fold signal amplification of a superconducting nanowire single-photon detector using a multiple-avalanche architecture

Superconducting nanowire avalanche single-photon detectors (SNAPs) with n parallel nanowires are advantageous over single-nanowire detectors because their output signal amplitude scales linearly with n. However, the SNAP architecture has not been viably demonstrated for n > 4. To increase n for larger signal amplification, we designed a multi-stage, successive-avalanche architecture which used nanowires, connected via choke inductors in a binary-tree layout. We demonstrated an avalanche detector with n = 8 parallel nanowires and achieved eight-fold signal amplification, with a timing jitter of 54 ps.

Bias sputtered NbN and superconducting nanowire devices

Superconducting nanowire single photon detectors (SNSPDs) promise to combine near-unity quantum efficiency with >100 megacounts per second rates, picosecond timing jitter, and sensitivity ranging from x-ray to mid-infrared wavelengths. However, this promise is not yet fulfilled, as superior performance in all metrics is yet to be combined into one device. The highest single-pixel detection efficiency and the widest bias windows for saturated quantum efficiency have been achieved in SNSPDs based on amorphous materials, while the lowest timing jitter and highest counting rates were demonstrated in devices made from polycrystalline materials. Broadly speaking, the amorphous superconductors that have been used to make SNSPDs have higher resistivities and lower critical temperature (Tc) values than typical polycrystalline materials. Here, we demonstrate a method of preparing niobium nitride (NbN) that has lower-than-typical superconducting transition temperature and higher-than-typical resistivity. As we will ...

Free-space-coupled superconducting nanowire single-photon detectors for infrared optical communications

This paper describes the construction of a cryostat and an optical system with a free-space coupling efficiency of 56.5% ± 3.4% to a superconducting nanowire single-photon detector (SNSPD) for infrared quantum communication and spectrum analysis. A 1K pot decreases the base temperature to T = 1.7 K from the 2.9 K reached by the cold head cooled by a pulse-tube cryocooler. The minimum spot size coupled to the detector chip was 6.6 ± 0.11 µm starting from a fiber source at wavelength, λ = 1.55 µm. We demonstrated photon counting on a detector with an 8 × 7.3 µm2 area. We measured a dark count rate of 95 ± 3.35 kcps and a system detection efficiency of 1.64% ± 0.13%. We explain the key steps that are required to improve further the coupling efficiency.

Infrared transmissometer to measure the thickness of NbN thin films

We present an optical setup that can be used to characterize the thicknesses of thin NbN films to screen samples for fabrication and to better model the performance of the resulting superconducting nanowire single photon detectors. The infrared transmissometer reported here is easy to use, gives results within minutes, and is nondestructive. Thus, the thickness measurement can be easily integrated into the workflow of deposition and characterization. Comparison to a similar visible-wavelength transmissometer is provided.

A compact superconducting nanowire memory element operated by nanowire cryotrons

A superconducting loop stores persistent current without any ohmic loss, making it an ideal platform for energy efficient memories. Conventional superconducting memories use an architecture based on Josephson junctions (JJs) and have demonstrated access times less than 10 ps and power dissipation as low as

A scalable multi-photon coincidence detector based on superconducting nanowires

10^{-19}