Angel Sanz-Andrés

On sonic anemometer measurement theory

Abstract In this paper a model for the measuring process of sonic anemometers (ultrasound pulse based) is presented. The differential equations that describe the travel of ultrasound pulses are solved in the general case of non-steady, non-uniform atmospheric flow field. The concepts of instantaneous line-average and travelling pulse-referenced average are established and employed to explain and calculate the differences between the measured turbulent speed (travelling pulse-referenced average) and the line-averaged one. The limit k 1 l =1 established by Kaimal in 1968, as the maximum value which permits the neglect of the influence of the sonic measuring process on the measurement of turbulent components is reviewed here. Three particular measurement cases are analysed: A non-steady, uniform flow speed field, a steady, non-uniform flow speed field and finally an atmospheric flow speed field. In the first case, for a harmonic time-dependent flow field, Mach number, M (flow speed to sound speed ratio) and time delay between pulses have revealed themselves to be important parameters in the behaviour of sonic anemometers, within the range of operation. The second case demonstrates how the spatial non-uniformity of the flow speed field leads to an influence of the finite transit time of the pulses ( M ≠0) even in the absence of non-steady behaviour of the wind speed. In the last case, a model of the influence of the sonic anemometer processes on the measurement of wind speed spectral characteristics is presented. The new solution is compared to the line-averaging models existing in the literature. Mach number and time delay significantly distort the measurement in the normal operational range. Classical line averaging solutions are recovered when Mach number and time delay between pulses go to zero in the new proposed model. The results obtained from the mathematical model have been applied to the calculation of errors in different configurations of practical interest, such as an anemometer located on a meteorological mast and the transfer function of a sensor in an atmospheric wind. The expressions obtained can be also applied to determine the quality requirements of the flow in a wind tunnel used for ultrasonic anemometer calibrations.

Spacecraft thermal control

The space mission Space environment Keplerian orbits Conductive heat transfer Thermal radiation heat transfer Thermal control surfaces Insulation systems Radiators Louvers Mechanical interfaces Heat pipes Phase change capacitors Heaters Pumped fluid loops Thermoelectric cooling Cryogenic systems Thermal protection systems Thermal control design Thermal mathematical models Thermal control testing Conclusion.

Vehicle-induced loads on traffic sign panels

The determination of the loads on traffic sign panels in the current standards does not, in general, take into account the vehicle-induced loads, as explained by Quinn, Baker and Wright (QBW in what follows) (J. Wind Eng. Ind. Aerodyn. 89 (2001) 831). On the other hand, a report from Cali and Covert (CC) (J. Wind Eng. Ind. Aerodyn. 84 (2000) 87) indicates that in highway sign support structures, vehicle-induced loads have led to premature failures in some cases. The aim of this paper is to present a mathematical model for the vehicle-induced load on a flat sign panel, simple enough to give analytical results, but able to explain the main characteristics of the phenomenon. The results of the theoretical model help to explain the behaviour observed in the experiments performed in previous studies.

Train-induced pressure on pedestrians

Abstract A simple analytical model for the train-induced flow and its effects on pedestrians is presented in this paper. The expressions developed for the induced air velocity and pressure on the pedestrian surface, as well as their dependence with time, are obtained from unsteady potential theory. The relevant parameters and their effects are analysed, in particular the sensitivity of the pressure coefficient and its rate of change on the train and pedestrian transverse size, the distance to the tracks and the pressure measurement location on the pedestrian surface. In spite of the extreme simplicity of the model and the expressions obtained, good correlation is observed with previously existing experiments. With this work, an absence of published studies concerning analytical approaches to the problem of vehicle-induced pressure on pedestrians is intended to be covered, allowing for simplified testing procedures.

Wind tunnel analysis of the aerodynamic loads on rolling stock over railway embankments: the effect of shelter windbreaks.

Wind-flow pattern over embankments involves an overexposure of the rolling stock travelling on them to wind loads. Windbreaks are a common solution for changing the flow characteristic in order to decrease unwanted effects induced by the presence of cross-wind. The shelter effectiveness of a set of windbreaks placed over a railway twin-track embankment is experimentally analysed. A set of two-dimensional wind tunnel tests are undertaken and results corresponding to pressure tap measurements over a section of a typical high-speed train are herein presented. The results indicate that even small-height windbreaks provide sheltering effects to the vehicles. Also, eaves located at the windbreak tips seem to improve their sheltering effect.

Mathematical Analysis of the Effect of Rotor Geometry on Cup Anemometer Response

The calibration coefficients of two commercial anemometers equipped with different rotors were studied. The rotor cups had the same conical shape, while the size and distance to the rotation axis varied. The analysis was based on the 2-cup positions analytical model, derived using perturbation methods to include second-order effects such as pressure distribution along the rotating cups and friction. The comparison with the experimental data indicates a nonuniform distribution of aerodynamic forces on the rotating cups, with higher forces closer to the rotating axis. The 2-cup analytical model is proven to be accurate enough to study the effect of complex forces on cup anemometer performance.

Pumped fluid loops

The aim of this chapter is to introduce pumped fluid loops, explaining their application in the field of high heat loads, their basic physical principles, and their main types (single-phase, and two-phase flow fluid loops). Both types of fluid loops are outlined, including their main characteristics, the working fluids employed, and their main components (heat exchangers, pumps, additives to reduce pressure loads, evaporators, accumulators). Finally, the description of their operation is provided, as well as flight experiences.

Nonlinear analysis of a simple model of temperature evolution in a satellite

We analyze a simple model of the heat transfer to and from a small satellite orbiting round a solar system planet. Our approach considers the satellite isothermal, with external heat input from the environment and from internal energy dissipation, and output to the environment as black-body radiation. The resulting nonlinear ordinary differential equation for the satellite’s temperature is analyzed by qualitative, perturbation and numerical methods, which prove that the temperature approaches a periodic pattern (attracting limit cycle). This approach can occur in two ways, according to the values of the parameters: (i) a slow decay towards the limit cycle over a time longer than the period, or (ii) a fast decay towards the limit cycle over a time shorter than the period. In the first case, an exactly soluble average equation is valid. We discuss the consequences of our model for the thermal stability of satellites.

A small platform for astrophysical research based on the UPM-Sat 1 satellite of the Universidad Politécnica de Madrid

UPM-Sat 1 is a small scientific, in-orbit demonstration, educational satellite which has been designed, built, tested, integrated, launched and operated by a team of professors, students, and auxiliary personnel belonging to the Universidad Politecnica de Madrid (UPM). After completion of UPM-Sat 1 Mission a new small satellite, UPM-Sat 2, oriented to low-Earth-orbit scientific mission has been designed. In this paper the different subsystems of UPM-Sat 1 are described and the main characteristics of the second small satellite UPM-Sat 2 are outlined.

Model of the Aerodynamic Behavior of a Pararotor

A simple semi-empirical model for the aerodynamic behavior of a low-aspect ratio pararotor in autorotation at low Reynolds numbers is presented. The paper is split into three sections: Sec. II deals with the theoretical model derivation, Sec. III deals with the wind-tunnel measurements needed for tuning the theoretical model, and Sec. IV deals with the tuning between the theoretical model and the experimental data. The study is focused on the effect of both the blade pitch angle and the blade roughness and also on the stream velocity, on the rotation velocity, and on the drag of a model. Flow pattern visualizations have also been performed. The value of the free aerodynamic parameters of the semi-empirical model that produces the best fit with the experimental results agrees with the expected ones for the blades at the test conditions. Finally, the model is able to describe the behavior of a pararotor in autorotation that rotates fixed to a shaft, validated for a range of blade pitch angles. The movement of the device is found to be governed by a reduced set of dimensionless parameters.