Anton Manakhov

A Novel Dry Chemical Path Way for Diene and Dienophile Surface Functionalization toward Thermally Responsive Metal–Polymer Adhesion

In this paper, we report a new and easily up-scalable dry chemical method to functionalize with diene and dienophile groups a large range of surfaces, such as metal, polymer, or glass, and we demonstrate the potentiality of this technique to realize thermally responsive adhesion between these materials. A complete and extensive surface chemistry analysis of the grafted surfaces, based on the deposition of an anhydride-rich thin plasma polymer layer by using an atmospheric pressure dielectric barrier discharge (DBD) plasma process, and its subsequent gas phase aminolysis reaction with specific diene or dienophile compound is discussed. The optimization of the assembling condition for these tailored surfaces has led to achieve a Diels-Alder adhesion force up to 0.6 N/mm at ambient temperature, which can be reduced by a factor of 50 when the retro Diels-Alder is ignited at a heating temperature around 200 °C. The study of the failure interface produced after peeling tests is presented and a mechanism of failure is proposed, based on forensic analyses involving surface analytical techniques such as XPS, ToF-SIMS, and SEM combined to AFM analyses for the retrieving of chemical and morphological information.

Cell proliferation on modified DLC thin films prepared by plasma enhanced chemical vapor deposition

Recently, diamondlike carbon (DLC) thin films have gained interest for biological applications, such as hip and dental prostheses or heart valves and coronary stents, thanks to their high strength and stability. However, the biocompatibility of the DLC is still questionable due to its low wettability and possible mechanical failure (delamination). In this work, DLC:N:O and DLC: SiOx thin films were comparatively investigated with respect to cell proliferation. Thin DLC films with an addition of N, O, and Si were prepared by plasma enhanced CVD from mixtures of methane, hydrogen, and hexamethyldisiloxane. The films were optically characterized by infrared spectroscopy and ellipsometry in UV-visible spectrum. The thickness and the optical properties were obtained from the ellipsometric measurements. Atomic composition of the films was determined by Rutherford backscattering spectroscopy combined with elastic recoil detection analysis and by x-ray photoelectron spectroscopy. The mechanical properties of the films were studied by depth sensing indentation technique. The number of cells that proliferate on the surface of the prepared DLC films and on control culture dishes were compared and correlated with the properties of as-deposited and aged films. The authors found that the level of cell proliferation on the coated dishes was high, comparable to the untreated (control) samples. The prepared DLC films were stable and no decrease of the biocompatibility was observed for the samples aged at ambient conditions.

Effect of Hydrogen Exposure on Mechanical and Tribological Behavior of CrxN Coatings Deposited at Different Pressures on IN718

In the current study, the properties of the CrxN coatings deposited on the Inconel 718 superalloy using direct current reactive magnetron sputtering are investigated. The influence of working pressure on the microstructure, mechanical, and tribological properties of the CrxN coatings before and after high-temperature hydrogen exposure is studied. The cross-sectional scanning electron micrographs indicate the columnar structure of the coatings, which changes from dense and compact columns to large columns with increasing working pressure. The Cr/N ratio increases from 1.4 to 1.9 with increasing working pressure from 300 to 900 mPa, respectively. X-ray diffraction analysis reveals a change from mixed hcp-Cr2N and fcc-CrN structure to approximately stoichiometric Cr2N phase. After gas-phase hydrogenation, the coating deposited at 300 mPa exhibits the lowest hydrogen absorption at 600 °C of all investigated coatings. The results indicate that the dense mixed cubic and hexagonal structure is preferential for hydrogen permeation resistance due to the presence of cubic phase with higher packing density in comparison to the hexagonal structure. After hydrogenation, no changes in phase composition were observed; however, a small amount of hydrogen is accumulated in the coatings. An increase of coating hardness and elastic modulus was observed after hydrogen exposure. Tribological tests reveal that hydrogenation leads to a decrease of the friction coefficient up to 20%–30%. The best value of 0.25 was reached for hydrogen exposed CrxN coating deposited at 300 mPa.

High-Performance Ammonia Gas Sensors Based on Plasma Treated Carbon Nanostructures

Sensors based on multi-walled carbon nanotubes were functionalized by oxygen plasma treatment and plasma co-polymerization of maleic anhydride and acetylene, obtaining core-shell carbon nanopartices covered by functional groups. The active nanostructured carbonaceous material was investigated by scanning electron microscopy, energy dispersive X-ray spectroscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy. It was confirmed that plasma treatment increases the content of surface functional groups. The sensing properties of the functionalized material were measured in the range of 10–1000 ppm of NH3 at room temperature. The plasma treated sensor showed an extremely high response of 22.5%, 27.9%, and 31.4% to 100 ppm, 250 ppm, and 500 ppm of NH3, respectively. It was shown that the nature of NH3 adsorption on the surface of functionalized nanostructured carbon material is physical adsorption.

BN nanoparticle/Ag hybrids with enhanced catalytic activity: theory and experiments

Hexagonal boron nitride nanoparticles (BNNPs) with different amounts of boron oxide on their surfaces were used as catalyst carriers. BNNPs/Ag nanohybrids were produced via ultraviolet (UV) decomposition of AgNO3 in a mixture of polyethylene glycol and BNNPs. High temperature (1600 °C, 1.5 h) vacuum annealing of BNNPs promoted small size (5–10 nm) Ag nanoparticle (AgNPs) formation on BN surfaces with narrow size distribution, whereas using BNNPs in their as-produced state resulted in large AgNPs with various sizes. An increase in the B2O3 content on the BNNPs surfaces (up to a certain point) during BNNP pre-annealing in air led to larger amounts of AgNPs on their surfaces. Experimental results were confirmed by theoretical calculations of the adhesion energy of the (111)Ag with (0001)h-BN and (100)B2O3 surfaces. In contrast to the nonwettability of the h-BN surface by AgNPs, silver bound well to B2O3 with the formation of a covalent bond at the interface. Excessive fraction of B2O3, however, was not beneficial in terms of obtaining the optimal contents of AgNPs. Results of catalytic activity tests demonstrated that BNNPs/Ag nanohybrids synthesized using BNNPs with an optimized amount of B2O3 possess significantly enhanced catalytic activity compared to BNNPs without or with excess amounts of oxide. Finally, the catalytic activity of nanohybrids was theoretically analyzed using density functional theory (DFT) calculations.

BN/Ag hybrid nanomaterials with petal-like surfaces as catalysts and antibacterial agents

BN/Ag hybrid nanomaterials (HNMs) and their possible applications as novel active catalysts and antibacterial agents are investigated. BN/Ag nanoparticle (NP) hybrids were fabricated using two methods: (i) chemical vapour deposition (CVD) of BN NPs in the presence of Ag vapours, and (ii) ultraviolet (UV) decomposition of AgNO3 in a suspension of BN NPs. The hybrid microstructures were studied by high-resolution transmission electron microscopy (HRTEM), high-angular dark field scanning TEM imaging paired with energy dispersion X-ray (EDX) mapping, X-ray photoelectron spectroscopy (XPS), and infrared spectroscopy (FTIR). They were also characterized in terms of thermal stability, Ag+ ion release, catalytic and antibacterial activities. The materials synthesized via UV decomposition of AgNO3 demonstrated a much better catalytic activity in comparison to those prepared using the CVD method. The best catalytic characteristics (100% methanol conversion at 350 °C) were achieved using the UV BN/Ag HNMs without preliminary annealing at 600 °C in an oxidizing atmosphere. Both types of the BN/Ag HNMs possess a profound antibacterial effect against Escherichia coli K-261 bacteria.

Immobilization of Platelet-Rich Plasma onto COOH Plasma-Coated PCL Nanofibers Boost Viability and Proliferation of Human Mesenchymal Stem Cells

The scaffolds made of polycaprolactone (PCL) are actively employed in different areas of biology and medicine, especially in tissue engineering. However, the usage of unmodified PCL is significantly restricted by the hydrophobicity of its surface, due to the fact that its inert surface hinders the adhesion of cells and the cell interactions on PCL surface. In this work, the surface of PCL nanofibers is modified by Ar/CO2/C2H4 plasma depositing active COOH groups in the amount of 0.57 at % that were later used for the immobilization of platelet-rich plasma (PRP). The modification of PCL nanofibers significantly enhances the viability and proliferation (by hundred times) of human mesenchymal stem cells, and decreases apoptotic cell death to a normal level. According to X-ray photoelectron spectroscopy (XPS), after immobilization of PRP, up to 10.7 at % of nitrogen was incorporated into the nanofibers surface confirming the grafting of proteins. Active proliferation and sustaining the cell viability on nanofibers with immobilized PRP led to an average number of cells of 258 ± 12.9 and 364 ± 34.5 for nanofibers with ionic and covalent bonding of PRP, respectively. Hence, our new method for the modification of PCL nanofibers with PRP opens new possibilities for its application in tissue engineering.

Antibacterial Performance of TiCaPCON Films Incorporated with Ag, Pt and Zn: Bactericidal Ions versus Surface Micro-Galvanic Interactions

It is very important to prevent bacterial colonization at the early postoperative stages. There are four major strategies and their corresponding types of antibacterial surfaces specifically designed to fight infection: bactericide release, anti-adhesion, pH-sensitive, and contact-killing. Herein, we aimed at determining the antibacterial efficiency of different types of bactericidal ions and revealing the possible contribution of surface microgalvanic effects arising from a potential difference on heterogeneous surfaces. We considered five types of TiCaPCON films, with Ag, Zn, Pt, Ag + Zn, and Pt + Zn nanoparticles (NPs) on their surface. The Ag-modified film demonstrated a pronounced antibacterial effect at a very low Ag ion concentration of 0.11 ppb in physiological solution that was achieved already after 3 h of immersion in Escherichia coli ( E. coli) bacterial culture. The Zn-containing sample also showed a noticeable antibacterial effect against E. coli and Staphylococcus aureus ( S. aureus) strains, wherein the concentration of Zn ions was 2 orders of magnitude higher (15 ppb) compared with the Ag ions. The presence of Ag NPs accelerated the leaching of Zn ion out of the TiCaPCON-Ag-Zn film, but no synergistic effect of the simultaneous presence of the two bactericidal components was observed. After the incubation of the samples with Ag, Zn, and Ag + Zn NPs in E. coli and S. aureus suspensions for 24 and 8 h, respectively, all bacterial cells were completely inactivated. The Pt-containing film showed a very low Pt ion release, and therefore the contribution of this type of ions to the total bactericidal effect could be neglected. The results of the electrochemical studies and Kelvin probe force microscopy indicated that microgalvanic couples were formed between the Pt NPs and the TiCaPCON film, but no noticeable antibacterial effect against either E. coli or S. aureus strains was observed. All ion-modified samples provided good osteoblastic cell attachment, spreading, and proliferation and therefore were concluded to be nontoxic for cells. In addition, the TiCaPCON films with Ag, Pt, and Zn NPs on their surface demonstrated good osteoconductive characteristics.

Biocompatibility of Thin Films Studied by Q-Phase

The interaction of amine-rich coatings and human fibroblasts was investigated by Q-Phase multimodal holographic microscope, which enables quantitative phase imaging. Based on the analysis of images, amine-rich films enhance the viability of the human fibroblasts.