Antonio Consoli

Decoupling gain and feedback in coherent random lasers: experiments and simulations

We propose and demonstrate a coherent random laser in which the randomly distributed scattering centres are placed outside the active region. This architecture is implemented by enclosing a dye solution between two agglomerations of randomly positioned titanium dioxide nanoparticles. The same spectral signature, consisting of sharp spikes with random spectral positions, is detected emerging from both ensembles of titanium dioxide nanoparticles. We interpret this newly observed behaviour as due to the optical feedback given by back-scattered light from the scattering agglomerations, which also act as output couplers. A simple model is presented to simulate the observed behaviour, considering the amplitude and phase round trip conditions that must be satisfied to sustain lasing action. Numerical simulations reproduce the experimental reports, validating our simple model. The presented results suggest a new theoretical and experimental approach for studying the complex behavior of coherent random lasers and stimulate the realization of new devices based on the proposed architecture, with different active and scattering materials.

High-peak-power pulse generation from a monolithic master oscillator power amplifier at 1.5 μm

We present an experimental study on the generation of high-peak-power short optical pulses from a fully integrated master-oscillator power-amplifier emitting at 1.5 μm. High-peak-power (2.7 W) optical pulses with short duration (100 ps) have been generated by gain switching the master oscillator under optimized driving conditions. The static and dynamic characteristics of the device have been studied as a function of the driving conditions. The ripples appearing in the power-current characteristics under cw conditions have been attributed to mode hopping between the master oscillator resonant mode and the Fabry-Perot modes of the entire device cavity. Although compound cavity effects have been evidenced to affect the static and dynamic performance of the device, we have demonstrated that trains of single-mode short optical pulses at gigahertz frequencies can be conveniently generated in these devices.

Pulse shortening of gain switched single mode semiconductor lasers using a variable delay interferometer

We propose a pulse shaping and shortening technique for pulses generated from gain switched single mode semiconductor lasers, based on a Mach Zehnder interferometer with variable delay. The spectral and temporal characteristics of the pulses obtained with the proposed technique are investigated with numerical simulations. Experiments are performed with a Distributed Feedback laser and a Vertical Cavity Surface Emitting Laser, emitting at 1.5 µm, obtaining pulse duration reduction of 25-30%. The main asset of the proposed technique is that it can be applied to different devices and pulses, taking advantage of the flexibility of the gain switching technique.

Simultaneously measuring two ultrashort laser pulses on a single-shot using double-blind frequency-resolved optical gating

We demonstrate a simple self-referenced single-shot method for simultaneously measuring two different arbitrary pulses, which can potentially be complex and also have very different wavelengths. The method is a variation of cross-correlation frequency-resolved optical gating (XFROG) that we call double-blind (DB) FROG. It involves measuring two spectrograms, both of which are obtained simultaneously in a single apparatus. DB FROG retrieves both pulses robustly by using the standard XFROG algorithm, implemented alternately on each of the traces, taking one pulse to be “known” and solving for the other. We show both numerically and experimentally that DB FROG using a polarization-gating beam geometry works reliably and appears to have no nontrivial ambiguities.

Large area resonant feedback random lasers based on dye-doped biopolymer films

We report resonant feedback random lasing from dye-doped biopolymer films, consisting of a deoxyribonucleic acid-cetyltrimethylammonium (DNA-CTMA) complex doped with DCM dye. In the proposed devices, the optical feedback for random lasing is given by scattering centers randomly positioned along the edges of the active area. Scattering elements are either titanium dioxide nanoparticles or random defects at the interface between active polymer and air. Different emission spectra are observed, depending on the geometry of the excited area. A single random resonator with dimensions of 2.6 mm x 0.65 mm is fabricated and random emission with resonant feedback is obtained by uniformly pumping the full device.

Pseudo-Random Single Photon Counting for space-borne atmospheric sensing applications

The ability to accurately observe the Earths carbon cycles from space gives scientists an important tool to analyze climate change. Current space-borne Integrated-Path Differential Absorption (IPDA) lidar concepts have the potential to meet this need. They are mainly based on the pulsed time-of-flight principle, in which two high energy pulses of different wavelengths interrogate the atmosphere for its transmission properties and are backscattered by the ground. In this paper, feasibility study results of a Pseudo-Random Single Photon Counting (PRSPC) IPDA lidar are reported. The proposed approach replaces the high energy pulsed source (e.g. a solid-state laser), with a semiconductor laser in CW operation with a similar average power of a few Watts, benefiting from better efficiency and reliability. The auto-correlation property of Pseudo-Random Binary Sequence (PRBS) and temporal shifting of the codes can be utilized to transmit both wavelengths simultaneously, avoiding the beam misalignment problem experienced by pulsed techniques. The envelope signal to noise ratio has been analyzed, and various system parameters have been selected. By restricting the telescopes field-of-view, the dominant noise source of ambient light can be suppressed, and in addition with a low noise single photon counting detector, a retrieval precision of 1.5 ppm over 50 km along-track averaging could be attained. We also describe preliminary experimental results involving a negative feedback Indium Gallium Arsenide (InGaAs) single photon avalanche photodiode and a low power Distributed Feedback laser diode modulated with PRBS driven acoustic optical modulator. The results demonstrate that higher detector saturation count rates will be needed for use in future spacebourne missions but measurement linearity and precision should meet the stringent requirements set out by future Earth-observing missions.

Characterization of Gain-Switched Pulses From 1.55-

We report on short optical pulse generation by gain-switching (GS) a low-cost commercial vertical-cavity surface-emitting laser emitting at 1.55 μm. The dependence of pulse characteristics on GS parameters is investigated and analyzed. Pulses with duration of 55 ps and time-bandwidth product between 0.91 and 2.2 are obtained at repetition rates between 1 and 3 GHz.

\mu

Two major elements are required in a laser device: light confinement and light amplification. Light confinement is obtained in optical cavities by employing a pair of mirrors or by periodic spatial modulation of the refractive index as in photonic crystals and Bragg gratings. In random lasers, randomly placed nanoparticles embedded in the active material provide distributed optical feedback for lasing action. Recently, we demonstrated a novel architecture in which scattering nanoparticles and active element are spatially separated and random lasing is observed. Here we show that this approach can be extended to scattering media with macroscopic size, namely, a pair of sand grains, which act as feedback elements and output couplers, resulting in lasing emission. We demonstrate that the number of lasing modes depends on the surface roughness of the sand grains in use which affect the coherent feedback and thus the emission spectrum. Our findings offer a new perspective of material science and photonic structures, facilitating a novel and simple approach for the realization of new photonics devices based on natural scattering materials.

m VCSEL

We present results on the electrical characterization of commercial fiber pigtailed 1. 55 μm 2.5 Gb/s VCSEL based on InAlGaAs active region, tunnel junction (TJ), air-gap aperture and InAlGaAs/InAlAs mirrors. The current-voltage (I-V) characteristics were measured and the results were fitted to the analytical expressions of an equivalent circuit considering the TJ in series with the active junction and a series resistance. Carrier capture/escape effects were considered in order to account for the reduced value of the drop in the measured differential resistance at threshold. The electrical parameters of both junctions were determined, showing that the TJ was responsible for most of the voltage drop at threshold. High frequency electrical impedance measurements were used to determine internal parameters as well as the role of external parasitics. The results were analyzed using a small signal equivalent circuit which includes the TJ, carrier capture/escape effects, the cavity parasitics, and the electrical access. A good agreement between the experimental and the equivalent circuit impedances at different bias was obtained by considering the differential resistances of the active and tunnel junctions extracted from the I-V characteristics, yielding reasonable values of the dynamic time constants and of the recombination coefficients.

Lasing optical cavities based on macroscopic scattering elements

A new method for measuring the linewidth enhancement factor (α-parameter) of semiconductor lasers is proposed and discussed. The method itself provides an estimation of the measurement error, thus self-validating the entire procedure. The α-parameter is obtained from the temporal profile and the instantaneous frequency (chirp) of the pulses generated by gain switching. The time resolved chirp is measured with a polarization based optical differentiator. The accuracy of the obtained values of the α-parameter is estimated from the comparison between the directly measured pulse spectrum and the spectrum reconstructed from the chirp and the temporal profile of the pulse. The method is applied to a VCSEL and to a DFB laser emitting around 1550 nm at different temperatures, obtaining a measurement error lower than ± 8%.