Anwesha Mukherjee

Electrical characterization of conducting polypyrrole by THz time-domain spectroscopy

Using an optoelectronic THz beam system for THz time-domain spectroscopy (THz TDS), we have measured the absorption and index of refraction of a conducting polypyrrole film from low frequencies to 2.5 THz. From these measurements, the dc conductivity of 215/(Ω cm) and the complex conductance were obtained over this frequency range. All of the results were well fit by Drude theory, which gives a carrier scattering time of only 12.6 fs, less than 1/10 that of the semiconductors, thereby illustrating the disorder and low mobility of the polymer.

Highly Dense ZnO Nanowires Grown on Graphene Foam for Ultraviolet Photodetection

Growth of highly dense ZnO nanowires (ZnO NWs) is demonstrated on three-dimensional graphene foam (GF) using resistive thermal evaporation technique. Photoresponse of the as-grown hybrid structure of ZnO NWs on GF (ZnO NWs/GF) is evaluated for ultraviolet (UV) detection. Excellent photoresponse with fast response and recovery times of 9.5 and 38 s with external quantum efficiency of 2490.8% is demonstrated at low illumination power density of 1.3 mW/cm(2). In addition, due to excellent charge carrier transport, mobility of graphene reduces the recombination rate of photogenerated charge carriers, hence the lifetime of photogenerated free charge carriers enhances in the photodetectors.

Few-layer graphene/ZnO nanowires based high performance UV photodetector

A graphene and zinc oxide nanowires (G/ZnO NWs) based ultraviolet (UV) photodetector presents excellent responsivity and photocurrent gain with detectivity. Graphene due to higher charge carrier transport mobility induces faster response to UV illumination at the interface between ZnO and graphene with improved response and decay times as compared to a ZnO NWs device alone. A linear increase is revealed for both the responsivity and photocurrent gain of the G/ZnO NWs device with the applied bias. These results suggest that the G/ZnO NWs device exhibits great promise for highly efficient UV photodetectors.

Sandwiched assembly of ZnO nanowires between graphene layers for a self-powered and fast responsive ultraviolet photodetector

A heterostructure of graphene and zinc oxide (ZnO) nanowires (NWs) is fabricated by sandwiching an array of ZnO NWs between two graphene layers for an ultraviolet (UV) photodetector. This unique structure allows NWs to be in direct contact with the graphene layers, minimizing the effect of the substrate or metal electrodes. In this device, graphene layers act as highly conducting electrodes with a high mobility of the generated charge carriers. An excellent sensitivity is demonstrated towards UV illumination, with a reversible photoresponse even for a short period of UV illumination. Response and recovery times of a few milliseconds demonstrated a much faster photoresponse than most of the conventional ZnO nanostructure-based photodetectors. It is shown that the generation of a built-in electric field between the interface of graphene and ZnO NWs effectively contributes to the separation of photogenerated electron-hole pairs for photocurrent generation without applying any external bias. Upon application of external bias voltage, the electric field further increases the drift velocity of photogenerated electrons by reducing the charge recombination rates, and results in an enhancement of the photocurrent. Therefore, the graphene-based heterostructure (G/ZnO NW/G) opens avenues to constructing a novel heterostructure with a combination of two functionally dissimilar materials.

Electrical and optical characterization of conducting poly-3-methylthiophene film by THz time-domain spectroscopy

Using THz time-domain spectroscopy (THz-TDS), we have measured the absorption and dispersion of 7.5/( \Omega cm) conducting poly-3-methylthiophene film from low frequencies up to 4 THz. From these measurements the complex conductance that increases with increasing frequency was obtained over this frequency range. The results do not follow simple Drude theory and are not comparable with normal metal and semiconductors; the results were well fit by the localization-modified Drude theory.

Water-responsive carbon nanotubes for selective detection of toxic gases

Ammonia plays an important role in our daily lives and hence its quantitative and qualitative sensing has become necessary. Bulk structure of carbon nanotubes (CNTs) has been employed to detect the gas concentration of 10 ppm. Hydrophobic CNTs were turned to hydrophilic via the application of a ramp electric field that allowed confinement of a controlled amount of water inside CNT microstructure. These samples were then also used to detect different gases. A comparative study has been performed for sensing three reducing gases, namely, ammonia, sulphur-di-oxide, and hydrogen sulphide to elaborate the selectivity of the sensor. A considerable structural bending in the bulk CNT was observed on evaporation of the confined water, which can be accounted to the zipping of individual nanotubes. However, the rate of the stress induced on these bulk microstructures increased on the exposure of ammonia due to the change in the surface tension of the confined solvent. A prototype of an alarm system has been developed to illustrate sensing concept, wherein the generated stress in the bulk CNT induces a reversible loss in electrical contact that changes the equivalent resistance of the electrical circuit upon exposure to the gas.

Magnetic field induced tailoring of mechanical behavior of fluid filled micro porous carbon nanotube foam

Compressive loading of the carbon nanotube (CNT) has attracted much attention due to its entangled cellular like structure (CNT foam). This report investigates the mechanical behavior of magnetorheological fluid impregnated micro porous CNT foam that has not been realized before at this scale. Compressive behavior of CNT foam is found to greatly depend on the variation in both fluid viscosity as well as magnetic field intensity. Moreover, maximum achieved stress and energy absorption in CNT foam followed a power law behavior with the magnetic field intensity. Magnetic field induced movement of both CNT and iron oxide particles along the field direction is shown to dominate compressive behavior of CNT foam over highly attractive van der Waals forces between individual CNT. Therefore, this study demonstrates a method for tailoring the mechanical behavior of the fluid impregnated CNT foam.

The role of molecular recognition in charge transport properties of doped polyaniline.

Molecular recognition plays a significant role in the counterion-induced processibility, morphological features, and physical properties of doped polyaniline (PANI). The interaction of the counterion and solvent controls the chain conformation and, as a result, the formation of extended and localized electronic states; hence, it holds the key for tuning a wide range of electrical and optical properties of doped PANI. The combined effects of counterion, solvent, and processing conditions tune the metal-insulator transition, temperature dependence of conductivity, magnetoresistance, and so forth in doped PANI. The typical examples are shown in the case of PANI doped by camphor sulfonic acid, 2-acrylamido-2-methyl-1-propane sulfonic acid, and dodecylbenzoyl sulfonic acid.

Influence of charge traps in carbon nanodots on gas interaction

The nonlinear electrical characteristic of carbon nanodots (CNDs) has revealed important physical phenomena of charge trapping playing a dominant role in surface interactions. Functional groups on the surface of CNDs attract ambient water molecules which in turn act as charge traps and give rise to electrical hysteresis that plays a dominant role in understanding charge transport in CNDs on surface interactions. Hysteresis in the current-voltage response is further utilized to study the interaction of the CNDs with nitrogen dioxide gas as an external stimuli. The hysteresis area is observed to be dependent on the time of gas interaction with the CNDs, therefore revealing the interaction mechanism of the CNDs with the gas.

Graphene based multifunctional flame sensor

Recently, graphene has attracted much attention due to its unique electrical and thermal properties along with its high surface area, and hence presents an ideal sensing material. We report a novel configuration of a graphene based flame sensor by exploiting the response of few layer graphene to a flame along two different directions, where flame detection results from a difference in heat transfer mechanisms. A complete sensor module was developed with a signal conditioning circuit that compensates for any drift in the baseline of the sensor, along with a flame detection algorithm implemented in a microcontroller to detect the flame. A pre-defined threshold for either of the sensors is tunable, which can be varied based on the nature of the flame, hence presenting a system that can be used for detection of any kind of flame. This finding also presents a scalable method that opens avenues to modify complicated sensing schemes.