Arava Leela Mohana Reddy

Synthesis Of Nitrogen-Doped Graphene Films For Lithium Battery Application

We demonstrate a controlled growth of nitrogen-doped graphene layers by liquid precursor based chemical vapor deposition (CVD) technique. Nitrogen-doped graphene was grown directly on Cu current collectors and studied for its reversible Li-ion intercalation properties. Reversible discharge capacity of N-doped graphene is almost double compared to pristine graphene due to the large number of surface defects induced due to N-doping. All the graphene films were characterized by Raman spectroscopy, transmission electron microscopy, and X-ray photoemission spectroscopy. Direct growth of active electrode material on current collector substrates makes this a feasible and efficient process for integration into current battery manufacture technology.

Direct laser writing of micro-supercapacitors on hydrated graphite oxide films

Microscale supercapacitors provide an important complement to batteries in a variety of applications, including portable electronics. Although they can be manufactured using a number of printing and lithography techniques, continued improvements in cost, scalability and form factor are required to realize their full potential. Here, we demonstrate the scalable fabrication of a new type of all-carbon, monolithic supercapacitor by laser reduction and patterning of graphite oxide films. We pattern both in-plane and conventional electrodes consisting of reduced graphite oxide with micrometre resolution, between which graphite oxide serves as a solid electrolyte. The substantial amounts of trapped water in the graphite oxide makes it simultaneously a good ionic conductor and an electrical insulator, allowing it to serve as both an electrolyte and an electrode separator with ion transport characteristics similar to that observed for Nafion membranes. The resulting micro-supercapacitor devices show good cyclic stability, and energy storage capacities comparable to existing thin-film supercapacitors.

Coaxial MnO2/Carbon Nanotube Array Electrodes for High-Performance Lithium Batteries

Coaxial manganese oxide/carbon nanotube (CNT) arrays deposited inside porous alumina templates were used as cathodes in a lithium battery. Excellent cyclic stability and capacity of MnO2/CNT coaxial nanotube electrodes resulted from the hybrid nature of the electrodes with improved electronic conductivity and dual mechanism of lithium storage. The reversible capacity of the battery was increased by an order compared to template grown MnO2 nanotubes, making them suitable electrodes for advanced Li ion batteries.

Hybrid Nanostructures for Energy Storage Applications

Materials engineering plays a key role in the field of energy storage. In particular, engineering materials at the nanoscale offers unique properties resulting in high performance electrodes and electrolytes in various energy storage devices. Consequently, considerable efforts have been made in recent years to fulfill the future requirements of electrochemical energy storage using these advanced materials. Various multi-functional hybrid nanostructured materials are currently being studied to improve energy and power densities of next generation storage devices. This review describes some of the recent progress in the synthesis of different types of hybrid nanostructures using template assisted and non-template based methods. The potential applications and recent research efforts to utilize these hybrid nanostructures to enhance the electrochemical energy storage properties of Li-ion battery and supercapacitor are discussed. This review also briefly outlines some of the recent progress and new approaches being explored in the techniques of fabrication of 3D battery structures using hybrid nanoarchitectures.

Controlled, Stepwise Reduction and Band Gap Manipulation of Graphene Oxide

Graphene oxide (GO) has drawn tremendous interest as a tunable precursor in numerous areas, due to its readily manipulable surface. However, its inhomogeneous and nonstoichiometric structure makes achieving chemical control a major challenge. Here, we present a room-temperature based, controlled method for the stepwise reduction of GO, with evidence of sequential removal of each organic moiety. By analyzing signature infrared absorption frequencies, we identify the carbonyl group as the first to be reduced, while the tertiary alcohol takes the longest to be completely removed from the GO surface. Controlled reduction allows for progressive tuning of the optical gap from 3.5 eV down to 1 eV, while XPS spectra show a concurrent increase in the C/O ratio. This study is the first step toward selectively enhancing the chemical homogeneity of GO, thus providing greater control over its structure, and elucidating the order of removal of functional groups and hydrazine-vapor reduction.

LiNi1/3Co1/3Mn1/3O2–Graphene Composite as a Promising Cathode for Lithium-Ion Batteries

The use of graphene as a conductive additive to enhance the discharge capacity and rate capability of LiNi(1/3)Co(1/3)Mn(1/3)O(2) electrode material has been demonstrated. LiNi(1/3)Co(1/3)Mn(1/3)O(2) and its composite with graphene (90:10 wt %) were prepared by microemulsion and ball-milling techniques, respectively. The structural and morphological features of the prepared materials were investigated with powder X-ray diffraction, scanning electron microscopy, transmission electron microscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy. Characterization techniques depict single-phase LiNi(1/3)Co(1/3)Mn(1/3)O(2) with particle sizes in the range of 220-280 nm. Electrochemical studies on LiNi(1/3)Co(1/3)Mn(1/3)O(2) and LiNi(1/3)Co(1/3)Mn(1/3)O(2)-graphene were conducted using cyclic voltammetry, galvanostatic charge-discharge, and electrochemical impedance spectroscopy methods by constructing a lithium half-cell. Cyclic voltammograms show the well-defined redox peaks corresponding to Ni(2+)/Ni(4+). Charge-discharge tests were performed at different C rates: 0.05, 1, and 5 between 2.5 and 4.4 V. The results indicate the better electrochemical performance of the LiNi(1/3)Co(1/3)Mn(1/3)O(2)-graphene composite in terms of high discharge capacity (188 mAh/g), good rate capability, and good cycling performance compared to LiNi(1/3)Mn(1/3)Co(1/3)O(2). The improved electrochemical performance of the LiNi(1/3)Co(1/3)Mn(1/3)O(2)-graphene composite is attributed to a decrease in the charge-transfer resistance.

Binary and ternary atomic layers built from carbon, boron, and nitrogen.

Two-dimensional (2D) atomic layers derived from bulk layered materials are very interesting from both scientific and application viewpoints, as evidenced from the story of graphene. Atomic layers of several such materials such as hexagonal boron nitride (h-BN) and dichalcogenides are examples that complement graphene. The observed unconventional properties of graphene has triggered interest in doping the hexagonal honeycomb lattice of graphene with atoms such as boron (B) and nitrogen (N) to obtain new layered structures. Individual atomic layers containing B, C, and N of various compositions conform to several stable phases in the three-component phase diagram of B-C-N. Additionally, stacking layers built from C and BN allows for the engineering of new van-der-Waals stacked materials with novel properties. In this paper, the synthesis, characterization, and properties of atomically thin layers, containing B, C, and N, as well as vertically assembled graphene/h-BN stacks are reviewed. The electrical, mechanical, and optical properties of graphene, h-BN, and their hybrid structure are also discussed along with the applications of such materials.

Carbon nanotube-nanocup hybrid structures for high power supercapacitor applications.

Here, we design and develop high-power electric double-layer capacitors (EDLCs) using carbon-based three dimensional (3-D) hybrid nanostructured electrodes. 3-D hybrid nanostructured electrodes consisting of vertically aligned carbon nanotubes (CNTs) on highly porous carbon nanocups (CNCs) were synthesized by a combination of anodization and chemical vapor deposition techniques. A 3-D electrode-based supercapacitor showed enhanced areal capacitance by accommodating more charges in a given footprint area than that of a conventional CNC-based device.

Direct Synthesis of Lithium-Intercalated Graphene for Electrochemical Energy Storage Application

A novel approach for bulk synthesis of lithium-intercalated graphene sheets through the reduction of exfoliated graphene oxide in liquid ammonia and lithium metal is reported. It is demonstrated here that as-synthesized lithiated graphite oxide sheets (Li-RGO) can be directly used as an electrode material in lithium batteries. The electrochemical studies on Li-RGO electrodes show a significant enhancement in the specific capacity of the lithium battery over commercially available graphite electrodes. Partial intercalation of lithium ions in between graphene layers makes this material a good candidate for electrochemical energy storage applications.

Three-Dimensionally Engineered Porous Silicon Electrodes for Li Ion Batteries

The ultimate goal of Li ion battery design should consist of fully accessible metallic current collectors, possibly of nanoscale dimensions, intimately in contact with high capacity stable electrode materials. Here we engineer three-dimensional porous nickel based current collector coated conformally with layers of silicon, which typically suffers from poor cycle life, to form high-capacity electrodes. These binder/conductive additive free silicon electrodes show excellent electrode adhesion resulting in superior cyclic stability and rate capability. The nickel current collector design also allows for an increase in silicon loading per unit area leading to high areal discharge capacities of up to 0.8 mAh/cm(2) without significant loss in rate capability. An excellent electrode utilization (∼85%) and improved cyclic stability for the metal/silicon system is attributed to reduced internal stresses/fracture upon electrode expansion during cycling and shorter ionic/electronic diffusion pathways that help in improving the rate capability of thicker silicon layers.