Ashish Dubey

Strategic review of secondary phases, defects and defect-complexes in kesterite CZTS–Se solar cells

Earth abundant kesterite copper-zinc-tin-sulfide–selenide (CZTS–Se) is considered as cost-effective material for next generation solar cells. However, current CZTS–Se solar cells have much lower efficiency than CIGS solar cells. Rapid progress in achieving the target efficiency in CZTS–Se solar cells is hindered by the narrow phase stability of the quaternary phase, Cu2ZnSn(SxSe1−x)4, and the existence of other competitive and complex secondary phases and defects. This resulted in structural inhomogeneity, local fluctuation of open circuit voltage and high carrier recombination that finally lead to poor device performance and repeatability issues. The higher performance of off-stoichiometric CZTS materials, copper-poor and zinc-rich, and their inherent association with secondary phases and defects force the scientific community to investigate them together. This work aims to provide a comprehensive review for optimum growth conditions to achieve efficient kesterite CZTS–Se material under different conditions, complementary characterization techniques to detect unwanted phases, defects and defect-complexes and various approaches to reduce the secondary phases, defects and defect-complexes for higher performance in CZTS–Se solar cells. Understanding and addressing the structural inhomogeneity, control growth and material characterization are expected to yield closer performance parity between CZTS–Se and CIGS solar cells.

Catalytic cracking of non-edible sunflower oil over ZSM-5 for hydrocarbon bio-jet fuel

Non-edible sunflower oils that were extracted from sunflower residual wastes were catalytically cracked over a ZSM-5 catalyst in a fixed-bed reactor at three different reaction temperatures: 450°C, 500°C and 550°C. The catalyst was characterized using XRD, FT-IR, BET and SEM. Characterizations of the upgraded sunflower oils, hydrocarbon fuels, distillation residues and non-condensable gases were carried out. The effect of the reaction temperature on the yield and quality of liquid products was discussed. The results showed that the reaction temperature affected the hydrocarbon fuel yield but had a minor influence on its properties. The highest conversion efficiency from sunflower oils to hydrocarbon fuels was 30.1%, which was obtained at 550°C. The reaction temperature affected the component content of the non-condensable gases. The non-condensable gases generated at 550°C contained the highest content of light hydrocarbons (C1-C5), CO, CO2 and H2. Compared to raw sunflower oils, the properties of hydrocarbon fuels including the dynamic viscosity, pH, moisture content, density, oxygen content and heating value were improved.

Interfacial Study To Suppress Charge Carrier Recombination for High Efficiency Perovskite Solar Cells.

We report effects of an interface between TiO2-perovskite and grain-grain boundaries of perovskite films prepared by single step and sequential deposited technique using different annealing times at optimum temperature. Nanoscale kelvin probe force microscopy (KPFM) measurement shows that charge transport in a perovskite solar cell critically depends upon the annealing conditions. The KPFM results of single step and sequential deposited films show that the increase in potential barrier suppresses the back-recombination between electrons in TiO2 and holes in perovskite. Spatial mapping of the surface potential within perovskite film exhibits higher positive potential at grain boundaries compared to the surface of the grains. The average grain boundary potential of 300-400 mV is obtained upon annealing for sequentially deposited films. X-ray diffraction (XRD) spectra indicate the formation of a PbI2 phase upon annealing which suppresses the recombination. Transient analysis exhibits that the optimum device has higher carrier lifetime and short carrier transport time among all devices. An optimum grain boundary potential and proper band alignment between the TiO2 electron transport layer (ETL) and the perovskite absorber layer help to increase the overall device performance.

Benzothiadiazole-based polymer for single and double junction solar cells with high open circuit voltage.

Single and double junction solar cells with high open circuit voltage were fabricated using poly{thiophene-2,5-diyl-alt-[5,6-bis(dodecyloxy)benzo[c][1,2,5]thiadiazole]-4,7-diyl} (PBT-T1) blended with fullerene derivatives in different weight ratios. The role of fullerene loading on structural and morphological changes was investigated using atomic force microscopy (AFM) and X-ray diffraction (XRD). The XRD and AFM measurements showed that a higher fullerene mixing ratio led to breaking of inter-chain packing and hence resulted in smaller disordered polymer domains. When the PBT-T1:PC60BM weight ratio was 1 : 1, the polymer retained its structural order; however, large aggregated domains formed, leading to poor device performance due to low fill factor and short circuit current density. When the ratio was increased to 1 : 2 and then 1 : 3, smaller amorphous domains were observed, which improved photovoltaic performance. The 1 : 2 blending ratio was optimal due to adequate charge transport pathways giving rise to moderate short circuit current density and fill factor. Adding 1,8-diiodooctane (DIO) additive into the 1 : 2 blend films further improved both the short circuit current density and fill factor, leading to an increased efficiency to 4.5% with PC60BM and 5.65% with PC70BM. These single junction solar cells exhibited a high open circuit voltage at ∼ 0.9 V. Photo-charge extraction by linearly increasing voltage (Photo-CELIV) measurements showed the highest charge carrier mobility in the 1 : 2 film among the three ratios, which was further enhanced by introducing the DIO. The Photo-CELIV measurements with varying delay times showed significantly higher extracted charge carrier density for cells processed with DIO. Tandem devices using P3HT:IC60BA as bottom cell and PBT-T1:PC60BM as top cell exhibited a high open circuit voltage of 1.62 V with 5.2% power conversion efficiency.

Dye-sensitized solar cells based on spray-coated carbon nanofiber/TiO2 nanoparticle composite counter electrodes

Electrospun carbon nanofiber (ECN)/TiO2 nanoparticle composite counter electrodes (CEs) for dye-sensitized solar cells (DSSCs) were successfully prepared by spray-coating an ECN/TiO2 (1 : 1 by weight) mixture on a fluorine doped tin oxide (FTO)-glass substrate. TiO2 particles (Degussa P25) were used to bind carbon nanofibers and adhere them to the FTO-glass substrate. Electrochemical impedance spectroscopy (EIS) measurements revealed that the spray-coated ECN/TiO2 composite CEs have lower charge transfer resistance (Rct) and higher interfacial capacitance (Q) than those of Pt CEs. Cyclic voltammograms (CV) further indicated that ECN/TiO2 composite CEs have a faster tri-iodide reduction rate than those of Pt CEs. DSSCs fabricated using ECN/TiO2 CEs showed a power conversion efficiency (η) of 7.25% under 100 mW cm−2 light intensity, which is comparable to that of thermally deposited Pt based DSSCs (η = 7.57%). Moreover, ECN/TiO2 composite CE based DSSCs demonstrated almost equal power conversion efficiency to that of Pt based cells by adding only 8 wt% Pt, which unveiled a cost-effective alternative of costly Pt CEs in DSSCs.

Incorporation of plasmonic Au nanostars into photoanodes for high efficiency dye-sensitized solar cells

We have significantly improved the performance of dye-sensitized solar cells (DSSCs) by incorporating plasmonic Au nanostars into the TiO2 photoanode. Gold nanostars were synthesized and used as localized surface plasmons (LSPs) to enhance the light absorption of DSSCs. The Au nanostars exhibit near infrared (NIR) light absorption at ∼785 nm. The N719 and N749 dye based DSSC devices were fabricated with and without the incorporation of Au nanostars. The power conversion efficiency (PCE) of DSSCs using Au nanostars was increased by ∼20% from 7.1% to 8.4% for N719 cells and by ∼30% from 3.9% to 5.0% for N749 devices. The incident photon-to-current conversion efficiency (IPCE) was improved and the spectral response was broadened over the wavelength range of 380–1000 nm. Electrochemical impedance spectroscopy (EIS) showed that by incorporating Au nanostars, the charge recombination resistance Rct value decreased under both open-circuit and illumination conditions, which indicated high electron density generated in the device photoanode.

Room temperature, air crystallized perovskite film for high performance solar cells

For the first time, room temperature heating free growth and crystallization of perovskite films in ambient air without the use of thermal annealing is reported. Highly efficient perovskite nanorod-based solar cells were made using ITO/PEDOT:PSS/CH3NH3PbI3 nanorods/PC60BM/rhodamine/Ag. All the layers except PEDOT:PSS were processed at room temperature thereby eliminating the need for thermal treatment. Perovskite films were spin coated inside a N2 filled glovebox and immediately were taken outside in air having 40% relative humidity (RH). Exposure to humid air was observed to promote the crystallization process in perovskite films even at room temperature. Perovskite films kept for 5 hours in ambient air showed nanorod-like morphology having high crystallinity, with devices exhibiting the highest PCE of 16.83%, which is much higher than the PCE of 11.94% for traditional thermally annealed perovskite film based devices. It was concluded that moisture plays an important role in room temperature crystallization of pure perovskite nanorods, showing improved optical and charge transport properties, which resulted in high performance solar cells.

Device and morphological engineering of organic solar cells for enhanced charge transport and photovoltaic performance

Abstract. Conjugated polymers are potential materials for photovoltaic applications due to their high absorption coefficient, mechanical flexibility, and solution-based processing for low-cost solar cells. A bulk heterojunction (BHJ) structure made of donor–acceptor composite can lead to high charge transfer and power conversion efficiency. Active layer morphology is a key factor for device performance. Film formation processes (e.g., spray-coating, spin-coating, and dip-coating), post-treatment (e.g., annealing and UV ozone treatment), and use of additives are typically used to engineer the morphology, which optimizes physical properties, such as molecular configuration, miscibility, lateral and vertical phase separation. We will review electronic donor–acceptor interactions in conjugated polymer composites, the effect of processing parameters and morphology on solar cell performance, and charge carrier transport in polymer solar cells. This review provides the basis for selection of different processing conditions for optimized nanomorphology of active layers and reduced bimolecular recombination to enhance open-circuit voltage, short-circuit current density, and fill factor of BHJ solar cells.

Improved performance by morphology control via fullerenes in PBDT-TBT-alkoBT based organic solar cells

In this work, we report improved performance by controlling morphology using different fullerene derivatives in poly{2-octyldodecyloxy-benzo[1,2-b;3,4-b]dithiophene-alt-5,6-bis(dodecyloxy)-4,7-di(thieno[3,2-b]thiophen-2-yl)-benzo[c][1,2,5]thiadiazole} (PBDT-TBT-alkoBT) based organic solar cells. PC60BM and PC70BM fullerenes were used to investigate the characteristic changes in morphology and device performance. Fullerenes affect device efficiency by changing the active layer morphology. PC70BM with broader absorption than PC60BM resulted in reduced device performance which was elucidated by the intermixed granular morphology separating each larger grain in the PC70BM/polymer composite layer which created a higher density of traps. However after adding additive 1,8-diiodooctane (DIO), a fibrous morphology was observed due to the reduced solubility of the polymer and increased solubility of PC70BM in chloroform. The fibrous morphology improved charge transport leading to an increase in overall device performance. Atomic force microscopy (AFM), photo-induced charge extraction by linearly increasing voltage (photo-CELIV), and Kelvin probe force microscopy (KPFM) were used to investigate the nanoscale morphology of the active layer with different fullerene derivatives. For the PC60BM based active layer, AFM images revealed a dense fibrous morphology and more distinct fibrous morphology was observed by adding DIO. The PC70BM based active layer only exhibited an intermixed granular morphology instead of a fibrous morphology observed in the PC60BM based active layer. However, addition of DIO into the PC70BM based active layer led to fibrous morphology. When additive DIO was not used, a wider distribution of surface potential was observed for PC70BM than the PC60BM based active layer by KPFM measurements, indicating that polymer and fullerene domains are separated. When DIO was used, a narrower distribution of surface potential for both PC70BM and PC60BM based active layers was observed. Photo-CELIV experiments showed larger extracted charge carrier density and mobility in the PC70BM/DIO film.

Morphological Evolution and Its Impacts on Performance of Polymer Solar Cells

In this paper, the role of fullerene loading on the nanomorphology and photovoltaic performance of alternating copolymer poly{2-octyldodecyloxy-benzo[1,2-b;3,4-b] dithiophene-alt-5,6-bis(dodecyloxy)-4,7bis(thiophen-2-yl)-benzo[c] [1,2,5]-thiadiazole} (PBDT-ABT-1) blend films was investigated. The morphology of blend films with different Phenyl C-60-butyric acid methyl ester (PCBM) mixing ratios and solvent additives was studied using atomic force microscopy (AFM) and energy-filtered transmission electron microscopy (EFTEM). AFM and EFTEM images showed difference in the intermixing of polymer with fullerene between 1:1, 1:2, and 1:3 weight ratios. Polymer/PCBM intermixed domain size increases with higher PCBM weight ratios. X-ray diffraction measurements on the pristine polymer and blend films cast without additives did not show any peaks, suggesting an amorphous nature of PBDT-ABT-1. EFTEM images from the donor/acceptor composite showed intermixed polymer-PCBM domains separated by the polymer boundary. Furthermore, EFTEM images for di-iodooctane (DIO) additive cast film revealed purer polymer domain. Photo-charge extraction by linearly increasing voltage measurement exhibited that charge extraction is highest in the nanomorphology sample with a weight ratio of 1:2, corresponding to the lowest bimolecular recombination and the highest charge carrier mobility.