Aswani Yella

Porphyrin-Sensitized Solar Cells with Cobalt (II/III)–Based Redox Electrolyte Exceed 12 Percent Efficiency

Simultaneous modification of the dye and redox shuttle boosts the efficiency of a dye-sensitized solar cell. The iodide/triiodide redox shuttle has limited the efficiencies accessible in dye-sensitized solar cells. Here, we report mesoscopic solar cells that incorporate a Co(II/III)tris(bipyridyl)–based redox electrolyte in conjunction with a custom synthesized donor-π-bridge-acceptor zinc porphyrin dye as sensitizer (designated YD2-o-C8). The specific molecular design of YD2-o-C8 greatly retards the rate of interfacial back electron transfer from the conduction band of the nanocrystalline titanium dioxide film to the oxidized cobalt mediator, which enables attainment of strikingly high photovoltages approaching 1 volt. Because the YD2-o-C8 porphyrin harvests sunlight across the visible spectrum, large photocurrents are generated. Cosensitization of YD2-o-C8 with another organic dye further enhances the performance of the device, leading to a measured power conversion efficiency of 12.3% under simulated air mass 1.5 global sunlight.

Molecular Engineering of Push–Pull Porphyrin Dyes for Highly Efficient Dye‐Sensitized Solar Cells: The Role of Benzene Spacers

Porphyrins have drawn much attention as sensitizers owing to the large absorption coefficients of their Soret and Q bands in the visible region. In a donor and acceptor zinc porphyrin we applied a new strategy of introducing 2,1,3-benzothiadiazole (BTD) as a π-conjugated linker between the anchoring group and the porphyrin chromophore to broaden the absorption spectra to fill the valley between the Soret and Q bands. With this novel approach, we observed 12.75% power-conversion efficiency under simulated one-sun illumination (AM1.5G, 100 mW cm(-2)). In this study, we showed the importance of introducing the phenyl group as a spacer between the BTD and the zinc porphyrin in achieving high power-conversion efficiencies. Time-resolved fluorescence, transient-photocurrent-decay, and transient-photovoltage-decay measurements were employed to determine the electron-injection dynamics and the lifetime of the photogenerated charge carriers.

Nanocrystalline Rutile Electron Extraction Layer Enables Low-Temperature Solution Processed Perovskite Photovoltaics with 13.7% Efficiency

We demonstrate low-temperature (70 °C) solution processing of TiO2/CH3NH3PbI3 based solar cells, resulting in impressive power conversion efficiency (PCE) of 13.7%. Along with the high efficiency, a strikingly high open circuit potential (VOC) of 1110 mV was realized using this low-temperature chemical bath deposition approach. To the best of our knowledge, this is so far the highest VOC value for solution-processed TiO2/CH3NH3PbI3 solar cells. We deposited a nanocrystalline TiO2 (rutile) hole-blocking layer on a fluorine-doped tin oxide (FTO) conducting glass substrate via hydrolysis of TiCl4 at 70 °C, forming the electron selective contact with the photoactive CH3NH3PbI3 film. We find that the nanocrystalline rutile TiO2 achieves a much better performance than a planar TiO2 (anatase) film prepared by high-temperature spin coating of TiCl4, which produces a much lower PCE of 3.7%. We attribute this to the formation of an intimate junction of large interfacial area between the nanocrystalline rutile TiO2 and the CH3NH3PbI3 layer, which is much more effective in extracting photogenerated electrons than the planar anatase film. Since the complete fabrication of the solar cell is carried out below 100 °C, this method can be easily extended to plastic substrates.

An Optically Transparent Iron Nickel Oxide Catalyst for Solar Water Splitting

Sunlight-driven water splitting to produce hydrogen fuel is an attractive method for renewable energy conversion. Tandem photoelectrochemical water splitting devices utilize two photoabsorbers to harvest the sunlight and drive the water splitting reaction. The absorption of sunlight by electrocatalysts is a severe problem for tandem water splitting devices where light needs to be transmitted through the larger bandgap component to illuminate the smaller bandgap component. Herein, we describe a novel method for the deposition of an optically transparent amorphous iron nickel oxide oxygen evolution electrocatalyst. The catalyst was deposited on both thin film and high-aspect ratio nanostructured hematite photoanodes. The low catalyst loading combined with its high activity at low overpotential results in significant improvement on the onset potential for photoelectrochemical water oxidation. This transparent catalyst further enables the preparation of a stable hematite/perovskite solar cell tandem device, which performs unassisted water splitting.

Sub‐Nanometer Conformal TiO2 Blocking Layer for High Efficiency Solid‐State Perovskite Absorber Solar Cells

A mere 2 nm conformal titanium dioxide overlayer coated by atomic layer deposition is shown to act as a blocking layer for high-efficiency solid-state perovskite (CH3NH3PbI3) absorber-based solar cells. Surpassing the existing multilayer passivation, this ultrathin sub-nanometer layer leads to a photovoltaic power conversion efficiency of 11.5%.

The Molecular Engineering of Organic Sensitizers for Solar‐Cell Applications

Positive to the core: ullazine has both strong electron-donating and weak accepting properties. This heterocycle was incorporated into sensitizers for dye-sensitized solar cells (DSCs). One of these sensitizers demonstrated strong light absorption across the UV/Vis region. The corresponding DSC device has a maximum IPCE of 95 % at 520 nm, with a power conversion efficiency of 8.4 %.

Bismuth‐Catalyzed Growth of SnS2 Nanotubes and Their Stability

Along with carbon nanotubes, non-carbon nanostructureshave attracted much attention over the past few years. Owingto their unusual geometry and promising physical properties,the study of inorganic fullerene nanostructures has becomeone of the key topics in nanoscale research since the firstreport on WS

Low temperature crystalline titanium dioxide by atomic layer deposition for dye-sensitized solar cells

Low-temperature processing of dye-sensitized solar cells (DSCs) is crucial to enable commercialization with low-cost, plastic substrates. Prior studies have focused on mechanical compression of premade particles on plastic or glass substrates; however, this did not yield sufficient interconnections for good carrier transport. Furthermore, such compression can lead to more heterogeneous porosity. To circumvent these problems, we have developed a low-temperature processing route for photoanodes where crystalline TiO2 is deposited onto well-defined, mesoporous templates. The TiO2 is grown by atomic layer deposition (ALD), and the crystalline films are achieved at a growth temperature of 200 °C. The ALD TiO2 thickness was systematically studied in terms of charge transport and performance to lead to optimized photovoltaic performance. We found that a 15 nm TiO2 overlayer on an 8 μm thick SiO2 film leads to a high power conversion efficiency of 7.1% with the state-of-the-art zinc porphyrin sensitizer and cobalt bipyridine redox mediator.

Towards Compatibility between Ruthenium Sensitizers and Cobalt Electrolytes in Dye‐Sensitized Solar Cells

This tuning minimizes energy losses in the device byoptimizingthedrivingforceforregeneration,whichallowsforconsiderableimprovementoftheopen-circuitvoltagerelativeto iodine electrolytes.Current ruthenium(II) sensitizers are not designed toperform with cobalt electrolytes. Among the few examplesreported in the literature,

Synthesis, Characterization, and Hierarchical Organization of Tungsten Oxide Nanorods: Spreading Driven by Marangoni Flow

Tungsten oxide nanorods were synthesized by a soft chemistry approach using tungsten alkoxide and trioctyl amine and oleic acid as the surfactants. The optical properties of the nanorods were studied. The nanorods were found to be soluble in a wide range of solvents like chloroform, cyclohexane, and so on. Upon solvent evaporation, the nanorods formed hierarchically organized solid state structures. Depending on the solvent used, the nanorods organized in different mesostructures. Moreover, the organization of the nanorods from mixtures of polar and nonpolar solvents was studied. Here, the Marangoni effect resulting from differences in the surface tensions of the two solvents was found to play a role in the organization of the nanorods. Furthermore, dip coating of the nanorod solutions on a mica substrate resulted in the formation of a uniform thin film of the nanorods, which may be useful for a variety of applications such as in electrochromic devices and in organic light emitting devices (OLEDs) using tungsten oxide as a buffer layer.