Azmil Haizam Ahmad Tarmizi

Physico-chemical changes occurring in oil when atmospheric frying is combined with post-frying vacuum application

The aim of this study was to investigate the effect of atmospheric frying followed by drainage under vacuum on the stability of oil, compared to similar frying with drainage at atmospheric pressure. Changes in the oil were assessed by the free fatty acid (FFA) content, p-anisidine value (AnV), colour, viscosity, fatty acid profile and concentration of tocols. The rate of FFA formation in the case of vacuum drainage was found to be about half that of atmospheric drainage. Oil deterioration by oxidation and polymerisation was also reduced by the use of vacuum drainage. The AnV of the oil after vacuum drainage was lower by about 12%, the total colour difference was improved by 14% and viscosity was slightly reduced after 5 days of frying, compared to the values for oil that had been drained at atmospheric pressure. There was a reduction in the loss of polyunsaturated fatty acids in the case of vacuum drainage after 5 days of frying but differences in retention of tocols were only evident in the first two days of frying.

The Possibility of Lowering Oil Content of Potato Chips by Combining Atmospheric Frying with Postfrying Vacuum Application

Four protocols involving the application of low pressures, either toward the end of frying or after frying, were investigated with the aim of lowering the oil content of potato chips. Protocol 1 involving frying at atmospheric pressure followed by a 3 min draining time constituted the control. Protocol 2 involved lowering of pressure to 13.33 kPa, 40 s before the end of frying, followed by draining for 3 min at the same pressure. Protocol 3 was the same as protocol 2, except that the pressure was lowered 3 s before the end of frying. Protocol 4 involved lowering the pressure to 13.33 kPa after the product was lifted from the oil and holding it at this value over the draining time of 3 min. Protocol 4 gave a product having the lowest oil content (37.12 g oil/100 g defatted dry matter), while protocol 2 gave the product with highest oil content (71.10 g oil/100 g defatted dry matter), followed by those obtained using protocols 1 and 3 (68.48 g oil/100 g defatted dry matter and 52.50 g oil/100 g defatted dry matter, respectively). Protocol 4 was further evaluated to study the effects of draining times and vacuum applied, and compared with the control. It was noted that over the modest range of pressures investigated, there was no significant effect of the vacuum applied on the oil content of the product. This study demonstrates that the oil content of potato chips can be lowered significantly by combining atmospheric frying with draining under vacuum.

Palm-Based Standard Reference Materials for Iodine Value and Slip Melting Point

This work described study protocols on the production of Palm-Based Standard Reference Materials for iodine value and slip melting point. Thirty-three laboratories collaborated in the inter-laboratory proficiency tests for characterization of iodine value, while thirty-two laboratories for characterization of slip melting point. The iodine value and slip melting point of palm oil, palm olein and palm stearin were determined in accordance to MPOB Test Methods p3.2:2004 and p4.2:2004, respectively. The consensus values and their uncertainties were based on the acceptability of statistical agreement of results obtained from collaborating laboratories. The consensus values and uncertainties for iodine values were 52.63 ± 0.14 Wijs in palm oil, 56.77 ± 0.12 Wijs in palm olein and 33.76 ± 0.18 Wijs in palm stearin. For the slip melting points, the consensus values and uncertainties were 35.6 ± 0.3 °C in palm oil, 22.7 ± 0.4 °C in palm olein and 53.4 ± 0.2 °C in palm stearin. Repeatability and reproducibility relative standard deviations were found to be good and acceptable, with values much lower than that of 10%. Stability of Palm-Based Standard Reference Materials remained stable at temperatures of −20 °C, 0 °C, 6 °C and 24 °C upon storage for one year.

Use of pilot plant scale continuous fryer to simulate industrial production of potato chips: thermal properties of palm olein blends under continuous frying conditions

Binary blends of palm olein (PO) with sunflower oil (SFO), canola oil (CNO), and cottonseed oil (CSO) were formulated to assess their stability under continuous frying conditions. The results were then compared with those obtained in PO. The oil blends studied were: (1) 60:40 for PO + SFO; (2) 70:30 for PO + CNO; and (3) 50:50 for PO + CSO. The PO and its blends were used to fry potato chips at 180°C for a total of 56 h of operation. The evolution of analytical parameters such as tocols, induction period, color, p-anisidine value, free fatty acid, smoke point, polar compounds, and polymer compounds were evaluated over the frying time. Blending PO with unsaturated oils was generally proved to keep most qualitative parameters comparable to those demonstrated in PO. Indeed, none of the oils surpassed the legislative limits for used frying. Overall, it was noted that oil containing PO and SFO showed higher resistance toward oxidative and hydrolytic behaviors as compared to the other oil blends.

Feasibility of Continuous Frying System to Improve the Quality Indices of Palm Olein for the Production of Extruded Product

Comparative frying studies on the processing of extruded product were conducted under intermittent and continuous frying conditions using two separate frying systems, i.e batch and pilot scale continuous fryers, respectively. Thermal resistance of palm olein were assessed for a total of 5 days of frying operation at 155°C - the unconventional frying temperature gave the product moisture content of 3% after intermittent and continuous frying for 2.5 min and 2 min, respectively. The formation of free fatty acid in palm olein in the case of intermittent frying was more than 2-fold higher compared to its counterpart (0.66%). Smoke point inversely evolved with oil acidity: the value dropped progressively from 215 to 177°C and from 219 to 188°C when extruded product was intermittently and continuously fried, respectively. In the light of induction period, repeated frying exhibited a gradual decrease in the value after 5 days of frying (12.2 h). Interestingly, continuous frying gave somewhat similar induction period, as demonstrated by fresh palm olein, across frying time. Frying at lower temperature, to some extent, provides opportunity for palm olein to retain 74% of its initial vitamin E during continuous frying. This benefit, however, is somehow denied when extruded product was processed under intermittent frying conditions--only 27% of vitamin E was remained at the end of frying session. Regardless of frying protocols, transient in polar compounds was minimal and hence comparable. The colour in the case of continuous frying appeared to be darker due to higher degree of oil utilisation for frying. The data obtained will provide useful information for food processors on how palm olein behaves when frying is undertaken under different frying protocols.

On the Possibility of Nonfat Frying using Molten Glucose

Fried products impose a health concerns due to considerable amount of oil they contain. Production of snack foods with minimal oil content and good management of oil during frying to minimize the production of toxic compounds continue to be challenging aims. This paper aims to investigate the possibility of producing a fat-free food snack by replacing frying oil with a nonfat medium. Glucose was melted and its temperature was then brought to 185 °C and used to fry potato strips, to obtain a product referred here as glucose fries. The resulting product was compared with French fries prepared conventionally under conditions that resulted in similar final moisture content. The resulting products were also examined for crust formation, texture parameters, color development and glucose content. Stereo microscope images showed that similar crusts were formed in the glucose fries and French fries. Texture parameters were found to be similar for both products at 5 and 2 mm penetration depth. The maximum hardness at 2 mm penetration depth was also similar for both products, but different from cooked potato. The color development that characterized French fries was also observed in glucose fries. The glucose content in glucose fries was found to be twice the content of French fries, which is to be expected because glucose absorbed or adhered to the surface. In conclusion, glucose fries, with similar texture and color characteristics to that of French fries, can be prepared by using a nonfat frying medium.

RANCIMAT TEST FOR MEASURING THE OXIDATIVE STABILITY OF COOKING OILS UPON PROLONGED FRYING: SHORT COMMUNICATION

The induction period or oxidative stability index (OSI) of four parent oils, i.e. palm olein (POo), soyabean oil (SBO), canola oil (CNO) and sunflower oil (SFO) was investigated and to be further compared with that of three binary blends of POo with SBO, CNO and SFO, respectively and one tertiary blend of POo with SBO and CNO. Two oil ratios of 90:10 and 50:50 were prepared for the binary blends of POo + SBO, POo + CNO and POo + SFO while 40:50:10 for POo + SBO + CNO. All the oils were used to fry French fries at 180°C for a total of 72 hr (8 hr daily for nine days) of intermittent frying. The stability of the oil was quantified by using the Rancimat test following the AOCS Official Method Cd 12b-92. Incorporation of POo has generally improved the induction period of the unsaturated oils as compared to their unary forms. Indeed, POo and its blends gave higher induction period after frying for 24 hr. Irrespective of oil types, the induction period was relatively comparable towards the end of frying sessions. The rate of induction period reduction is likely influenced by the presence of tocotrienol homologues in POo and its blends.

On the possibility of non-fat frying using molten glucose

Fried products impose a health concerns due to considerable amount of oil they contain. Production of snack foods with minimal oil content and good management of oil during frying to minimize the production of toxic compounds continue to be challenging aims. This paper aims to investigate the possibility of producing a fat-free food snack by replacing frying oil with a nonfat medium. Glucose was melted and its temperature was then brought to 185 °C and used to fry potato strips, to obtain a product referred here as glucose fries. The resulting product was compared with French fries prepared conventionally under conditions that resulted in similar final moisture content. The resulting products were also examined for crust formation, texture parameters, color development and glucose content. Stereo microscope images showed that similar crusts were formed in the glucose fries and French fries. Texture parameters were found to be similar for both products at 5 and 2 mm penetration depth. The maximum hardness at 2 mm penetration depth was also similar for both products, but different from cooked potato. The color development that characterized French fries was also observed in glucose fries. The glucose content in glucose fries was found to be twice the content of French fries, which is to be expected because glucose absorbed or adhered to the surface. In conclusion, glucose fries, with similar texture and color characteristics to that of French fries, can be prepared by using a nonfat frying medium.

On the Possibility of Nonfat Frying using Molten Glucose: Glucose frying…

Fried products impose a health concerns due to considerable amount of oil they contain. Production of snack foods with minimal oil content and good management of oil during frying to minimize the production of toxic compounds continue to be challenging aims. This paper aims to investigate the possibility of producing a fat-free food snack by replacing frying oil with a nonfat medium. Glucose was melted and its temperature was then brought to 185 °C and used to fry potato strips, to obtain a product referred here as glucose fries. The resulting product was compared with French fries prepared conventionally under conditions that resulted in similar final moisture content. The resulting products were also examined for crust formation, texture parameters, color development and glucose content. Stereo microscope images showed that similar crusts were formed in the glucose fries and French fries. Texture parameters were found to be similar for both products at 5 and 2 mm penetration depth. The maximum hardness at 2 mm penetration depth was also similar for both products, but different from cooked potato. The color development that characterized French fries was also observed in glucose fries. The glucose content in glucose fries was found to be twice the content of French fries, which is to be expected because glucose absorbed or adhered to the surface. In conclusion, glucose fries, with similar texture and color characteristics to that of French fries, can be prepared by using a nonfat frying medium.