k-Il Bae

Mechanical Characteristics of Ultra High Strength Concrete with Steel Fiber Under Uniaxial Compressive Stress

Design of fiber reinforced ultra-high strength concrete members should be verified with analytical or experimental methods for safety. Members with compressive strength larger than limitation of current design code usually be designed with analytical verification using stress-strain relation of concrete and reinforcements. For this purpose, mechanical characteristics of steel fiber reinforced ultra-high strength concrete were defined under uniaxial compression. Mix proportions of test specimens were based on reactive powder concrete and straight steel fibers were mixed with different volume fraction. Compressive strength of matrix were distributed from 80 MPa to 200 MPa. Effect of fiber inclusion were investigated : increase of compressive strength of concrete, elastic modulus and strain corresponding to peak stress. For the wide range application of investigation, previously tested test specimens were collected and used for investigation and estimation equation. Based on the investigation and evaluation of previous research results and estimation equation of mechanical characteristics of concrete, regression equations were suggested.

Shear Strength Reduction Ratio of Reinforced Concrete Shear Walls with Openings

There are many types of remodeling, however, engineers and architectures preferred to merge two or more separate units to one very spacious unit. Performing this type of remodeling, in the case of wall dominant apartments, requires partial removal of structural wall causing a concern of structural integrity. However, there are insufficient studies about partial removal, that is, openings. Presently, ACI standard have no clear way to evaluate the effect of opening on the structural wall. AIJ has the provision about strength reduction factor ``. However, this reduction factor cannot exactly evaluate the reduction effect of openings because this factor `` was determined through the elastic analysis. Therefore, in this study, 2 structural wall specimens were tested and many test results from previous studies were collected. Using these data, this study performed statistical analysis about strength of structural wall which have the opening in wall panel. And this study performed parametric study verifying shear strength reducing effect by opening area. In the results of statistical study, previous reduction factor show very conservative results because this equation did not consider other factors, reinforcement ratio and aspect ratio of openings, which was affect the shear strength of shear walls. Therefore we performed parametric study based on the test data and suggest new equation for shear strength reduction factor ``.

Correlation Between Tensile Strength and Compressive Strength of Ultra High Strength Concrete Reinforced with Steel Fiber

Ultra-high strength concrete which have 100 MPa compressive strength or higher can be developed applying RPC(Reactive Powder Concrete). Preventing brittle failure under compression and tension, ultra-high strength concrete usually use the steel fibers as reinforcements. For the effective use of steel fiber reinforced ultra-high strength concrete, estimation of tensile strength is very important. However, there are insufficient research results are available with no relation between them. Therefore, in this study, correlation between compressive strength and tensile strength of ultra-high strength concrete was investigated by test and statistical analysis. According to test results, increasing tendency of tensile strength was also shown in the range of ultra-high strength. Evaluation of test results of this study and collected test results were carried out. Using 284 splitting test specimens and 265 flexural test specimens, equations suggested by previous researchers cannot be applied to ultra-high strength concrete. Therefore, using database and test results, regression analysis was carried out and we suggested new equation for splitting and flexural tensile strength of steel fiber reinforced ultra-high strength concrete.

Experimental and Numerical Study on the Compression Behavior of Square Concrete-Filled Steel Tube Stub Columns with Steel Fiber-Reinforced High-Strength Concrete

This study was conducted to evaluate the applicability of concrete-filled steel tube (CFT) columns made from high-performance construction materials. KBC2016, South Korea’s current building code, limits the maximum compressive strength of concrete at 70 MPa and the maximum yield strength of steel at 650 MPa. Similar restrictions to material properties are imposed on major composite structural design parameters in other countries worldwide. With the recent acceleration of the pace of development in the field of material technology, the compressive strength of commercial concrete has been greatly improved and the problem of low tensile strength, known to be the major limitation of concrete, is being successfully addressed by adding fiber reinforcement to concrete. Therefore, the focus of this study was to experimentally determine the strength and ductility enhancement effects, which depend on material composition. To this end, we performed concentric axial loading tests on CFT stub columns made from steel with a yield strength of 800 MPa and steel fiber-reinforced high-strength concrete. By measuring the strain at the yield point of CFT steel during the test, we could determine whether steel yields earlier than ultimate failure load of the member, which is a key design concept of composite structures. The analysis results revealed that the yield point of steel preceded that of concrete on the stress-strain curve by the concurrent action of the strain increase at the maximum strength, attributable to the high compressive strength and steel fiber reinforcement, and the strain increase induced by the confining stress of the steel tube. Additionally, we performed parametric study using ABAQUS to establish the broad applications of CFT using high-performance materials, with the width-to-thickness ratio as the main parameter. Parametric study was undertaken as experimental investigation was not feasible, and we reviewed the criteria for limiting the width-to-thickness ratio as specified in the current building code.

Ductility of Ultra-High Performance Concrete and its Correlation with Tensile Strength Increase

In this study, ductility of members with ultra-high performance concrete was investigated using moment-curvature analysis for the verification of safety under large deformation of ultra-high performance concrete structural members. For the analysis of members with ultra-high performance concrete, mathematical stress-strain model was selected among the results conducted by other researchers on the compressive and tensile behavior of high strength concrete and fiber reinforced concrete. According to the investigation on ductility of members with ultra-high performance concrete, decrease of ductility was observed with increase of tensile strength of concrete under the same reinforcement ratio. Members with 2~3% of reinforcement ratio, which usually be used in the field engineering, show the decrease of ductility with increase of fiber volume fraction. As a results of parametric study, limitation of maximum reinforcement ratio ( or limitation of net tensile strain ) suggested by current design code is not safe when using ultra-high performance concrete.

Evaluation of Bond Strength between Steel Fiber Reinforced Ultra-High Strength Concrete and Rebar

In order to design reinforced concrete member using steel fiber ultra high strength concrete, current structural design methods should be re-evaluated because it has significant difference in material characteristics compared with normal concrete. In this study, bond strength of steel fiber reinforced ultra-high strength concrete was evaluated. For this purpose, direct pull out test specimens were constructed with variables of cover thickness, compressive strength of matrix and fiber inclusion ratio. According to the test, bond strength were sensitively varied with cover thickness and fiber inclusion. Because bond strength was determined by tensile strength of concrete. Comparing test results with theoretical methods suggested by Tepfers, specimens without steel fiber show good agreement with analytical method, because this method were based on elasticity. And other empirical equations were evaluated with other previous researches.

Correlation between Mix Proportion and Mechanical Characteristics of Steel Fiber Reinforced Concrete

The main purpose of this study is reducing the cost and effort for characterization of tensile strength of fiber reinforced concrete, in order to use in structural design. For this purpose, in this study, test for fiber reinforced concrete was carried out. Because fiber reinforced concrete is consisted of diverse material, it is hard to define the correlation between mix proportions and strength. Therefore, compressive strength test and tensile strength test were carried out for the range of smaller than 100 MPa of compressive strength and 0.25~1% of steel fiber volume fraction. as a results of test, two types of tensile strength were highly affected by compressive strength of concrete. However, increase rate of tensile strength was decreased with increase of compressive strength. Increase rate of tensile strength was decreased with increase of fiber volume fraction. Database was constructed using previous research data. Because estimation equations for tensile strength of fiber reinforced concrete should be multiple variable function, linear regression is hard to apply. Therefore, in this study, we decided to use the ANN(Artificial Neural Network). ANN was constructed using multiple layer perceptron architecture. Sigmoid function was used as transfer function and back propagation training method was used. As a results of prediction using artificial neural network, predicted values of test data and previous research which was randomly selected were well agreed with each other. And the main effective parameters are water-cement ratio and fiber volume fraction.

Bond Characteristics and Splitting Bond Stress on Steel Fiber Reinforced Reactive Powder Concrete

Structural members using ultra high strength concrete which usually used with steel fiber is designed with guidelines based on several investigation of SF-RPC(steel fiber reinforced reactive powder concrete). However, there are not clear design method yet. Especially, SF-RPC member should be casted with steam(90 degree delicious) and members with SF-RPC usually used with precast members. Although the most important design parameter is development method between SF-RPC and steel reinforcement(rebar), there are no clear design method in the SF-RPC member design guidelines. There are many controversial problems on safety and economy. Therefore, in order to make design more optimum safe design, in this study, we investigated bond stress between steel rebar and SF-RPC according to test. Test results were compared with previously suggested analysis method. Test was carried out with direct pull out test using variables of compressive strength of concrete, concrete cover and inclusion ratio of steel fiber. According to test results, bond stress between steel rebar and SF-RPC increased with increase of compressive strength of concrete and concrete cover. Increasing rate of bond stress were decrease with increase of compressive strength of SF-RPC and concrete cover significantly. 1% volume fraction inclusion of steel fiber increase the bond stress between steel rebar and SF-RPC with two times but 2% volume fraction cannot affect the bond stress significantly. There are no exact or empirical equations for evaluation of SF-RPC bond stress. In order to make safe bond design of SF-RPC precast members, previously suggested analysis method for bond stress by Tepfers were evaluated. This method have shown good agreement with test results, especially for steel fiber reinforced RPC.

The Effect of Anchorage with Shear Reinforcement in Flat Plate System

Flat plate are being used more in buildings requiring a high level of technical installations or in buildings needing changeable room arrangements during their life time such as office buildings. The main problem in flat plate is its weak resistance against a punching failure at its slab-column connections. Therefore, in this research, an experimental study on full-scale interior slab-column connection was performed. Three types of shear reinforcements were tested to prevent brittle punching shear failure that could lead to collapse of the structure. A series of four flat plate specimens including a specimen without shear reinforcement and three specimens with shear reinforcements were tested. The slabs were tested up to failure using monotonic vertical shear load- ing. The presences of the shear reinforcements substantially increased punching shear capacity and ductility of the interior slab- column connections. The test results showed that a slab that did not have enough bond length failed before shear reinforcement yielded due to anchorage slip. Also, FEM analyses were performed to study an effect of slab thickness and concrete compressive strength on the flat plate slab. The analytical study results were used to propose a method to calculate performance capacity of shear reinforcement in slab-column connection.

Retrofitting Effect of Unreinforced Masonry Walls Using FRPs

Unreinforced masonry buildings have significant portion of existing and historical buildings around the world. Recent earthquakes have shown the needs of seismic retrofitting for these types of buildings. There are many types of retrofitting materials for URM(unreinforced masonry buildings) such as shotcrete, ECC and FRPs. Many engineers use many types of fiber reinforced polymers because these types of material enhance the shear strength of wall without expansion of wall sectional area and additional weight of total structure. However, the complexity of mechanical behavior of masonry shear wall and the lack of experimental data of masonry wall which was retrofitted by FRPs may cause the problem that engineers hard to determine the retrofitting level. Determining and providing the information for retrofitting effect of FRPs for masonry shear wall, this paper investigate in-plane shear behavior of URM and retrofitted masonry shear walls using two types of different FRP materials. Specimens were designed to idealize the wall of low rise apartment which was built in 1970s Korea with no seismic reinforcements and have 1 aspect ratio. Retrofitting materials were carbon FRP and Hybrid sheet which have different elastic modulus and ultimate strain. Consequently, this study will evaluate the structural capacity of masonry shear wall and retrofitting effect of FRP sheet for in plane shear behavior comparing with evaluation method for reinforced concrete beam which was retrofitted by FRPs.