Bérengère Claude

Selective solid-phase extraction of a triterpene acid from a plant extract by molecularly imprinted polymer

A molecularly imprinted polymer (MIP) has been prepared by a thermal polymerisation method using methacrylic acid as functional monomer, ethylene glycol dimethacrylate as cross-linking agent, chloroform as porogenic solvent and an oleanane triterpene compound (18-beta-glycyrrhetinic acid) as imprinted molecule (template). Equilibrium ligand binding experiments were done to assess the performance of the MIP relative to non-imprinted polymer (NIP). After optimisation of SPE protocol (CHCl3 as washing solvent and MeOH as elution solvent), successful imprinting was confirmed by comparison of the recoveries between NIP (5%) and MIP (97%) cartridges. The binding capacity of the MIP for 18-beta-glycyrrhetinic acid was determined to be 0.94 mg g(-1). Four structurally related oleanane triterpenes (18-alpha-glycyrrhetinic acid, oleanolic acid, echinocystic acid, erythrodiol) were selected to assess the MIP selectivity. Experimental data illustrated the influence of functional groups on the triterpene skeleton. The MIP was applied to the solid-phase extraction of triterpenoids from a plant extract prior HPLC analysis. However, CHCl3 was replaced by ACN during the washing step in order to suppress non-specific interactions due to polar matrix components. A selective extraction of 18-beta-glycyrrhetinic acid from hydrolyzed extract of liquorice roots was achieved with a good extraction yield (98%).

Analysis of urinary neurotransmitters by capillary electrophoresis: sensitivity enhancement using field-amplified sample injection and molecular imprinted polymer solid phase extraction.

Capillary electrophoresis (CE) has been investigated for the analysis of some neurotransmitters, dopamine (DA), 3-methoxytyramine (3-MT) and serotonin (5-hydroxytryptamine, 5-HT) at nanomolar concentrations in urine. Field-amplified sample injection (FASI) has been used to improve the sensitivity through the online pre-concentration samples. The cationic analytes were stacked at the capillary inlet between a zone of low conductivity - sample and pre-injection plug - and a zone of high conductivity - running buffer. Several FASI parameters have been optimized (ionic strength of the running buffer, concentration of the sample protonation agent, composition of the sample solvent and nature of the pre-injection plug). Best results were obtained using H(3)PO(4)-LiOH (pH 4, ionic strength of 80 mmol L(-1)) as running buffer, 100 μmol L(-1) of H(3)PO(4) in methanol-water 90/10 (v/v) as sample solvent and 100 μmol L(-1) of H(3)PO(4) in water for the pre-injection plug. In these conditions, the linearity was verified in the 50-300 nmol L(-1) concentration range for DA, 3-MT and 5-HT with a determination coefficient (r(2)) higher than 0.99. The limits of quantification (10 nmol L(-1) for DA and 3-MT, 5.9 nmol L(-1) for 5-HT) were 500 times lower than those obtained with hydrodynamic injection. However, if this method is applied to the analysis of neurotransmitters in urine, the presence of salts in the matrix greatly reduces the sensitivity of the FASI/CE-UV method.Therefore, a solid phase extraction (SPE) on a dedicated imprinted polymer (MIP) was developed to extract specific neurotransmitters, catecholamines, metanephrines and indolamines, from urine. Matrix salts were thus discarded after sample extraction on AFFINIMIP™ Catecholamine & Metanephrine (100mg) cartridge. Therefore, lower limits of quantification were determined in artificial urine (46 nmol L(-1) for DA, 11 nmol L(-1) for 3-MT and 6 nmol L(-1) for 5-HT).The application of this protocol MIP-SPE/FASI-CE-UV analysis of neurotransmitters in human urine gave rise to electropherograms with a very good base line and signal to noise ratios above 15.

Interest of molecularly imprinted polymers in the fight against doping. Extraction of tamoxifen and its main metabolite from urine followed by high-performance liquid chromatography with UV detection.

A molecular imprinted polymer (MIP) has been synthesized in order to specifically extract tamoxifen, a nonsteroidal antiestrogen, and its metabolites from urine by solid-phase extraction (SPE) before HPLC-UV analysis. Clomiphene, a chlorinated tamoxifen analogue, was selected as template for MIP synthesis. Polymerisation was achieved by thermal polymerisation of methacrylic acid (MAA) as functional monomer, ethylene glycol dimethacrylate (EDMA) as cross-linking agent and acetonitrile as porogen. The efficient elimination of the urinary matrix has been obtained by MIP-SPE but the elution recovery of tamoxifen was initially too low ( approximately 14%). This problem has been overcome following two ways. At first, a preliminary HLB-SPE of the urine has enabled to discard endogenous salts and to percolate an organic sample through the MIP cartridge. Extraction recoveries are equal to 56 and 74% for tamoxifen and 4-hydroxytamoxifen, respectively. Then, a second MIP has been prepared with styrene and MAA as functional co-monomers. Strong pi-pi interactions occurring between phenyl groups of styrene and tamoxifen promote rebinding of the analyte by the specific sites. The enhanced hydrophobic character of the imprinted polymer has enabled the direct percolation of urine through MIP-SPE and the easy elimination of endogenous salts from urine with only one aqueous washing step. HPLC-UV analysis has confirmed high extraction recoveries (85%) for tamoxifen and its metabolite with an enrichment factor of 8. This analytical protocol can selectively detect the presence of tamoxifen metabolites in urines and be useful as a proof of doping in competitive sports.

Capillary electrophoresis procedure for the simultaneous analysis and stoichiometry determination of a drug and its counter-ion by using dual-opposite end injection and contactless conductivity detection: Application to labetalol hydrochloride

In this work, a capillary electrophoresis (CE) procedure was developed for the simultaneous determination of a pharmaceutical drug and its counter-ion, namely labetalol hydrochloride. For this purpose, an uncoated fused-silica capillary, a low conductivity background electrolyte (BGE) and a capacitively coupled contactless conductivity detector (C(4)D) were employed. This detection system is highly sensitive and enables detection of inorganic as well as organic ions unlike with direct UV detection. Moreover, to be able to simultaneously analyze the cationic drug (labetalol(+)) and its anionic counter-ion (Cl(-)) in the same electrophoretic run without the need of a coated capillary, a dual-opposite end injection was performed. In this technique, the sample is hydrodynamically injected into both ends of the capillary. This method is simple and easy to perform since the different injection steps are automated by the CE software. This novel CE-C(4)D procedure with dual-opposite end injection has been successfully validated and applied for the analysis of chloride content in an adrenergic antagonist (labetalol hydrochloride). Thus, the hereby developed method has been shown to enable fast (analysis time<10 min), precise (repeatability of migration times<0.7% and of corrected-peak areas < 3.3%; n=6) and rugged analyses for the simultaneous determination of a pharmaceutical drug and its counter-ion.

Synthesis and study of a molecularly imprinted polymer for the specific extraction of indole alkaloids from Catharanthus roseus extracts.

Two molecularly imprinted polymers (MIP) for catharanthine and vindoline have been synthesized in order to specifically extract these natural indole alkaloids from Catharanthus roseus by solid-phase extraction (SPE). Each MIP was prepared by thermal polymerisation using catharanthine (or vindoline) as template, methacrylic acid (or itaconic acid) as functional monomer, ethylene glycol dimethacrylate (EDMA) as cross-linking agent and acetonitrile (or acetone) as porogenic solvent. For catharanthine-MIP, a SPE protocol (ACN-AcOH 99/1 washing and MeOH-AcOH 90/10 elution) allows a good MIP/NIP selectivity (imprinting factor 12.6). The specificity of catharanthine-MIP versus related bisindole alkaloids was assessed by cross-reactivity study. The catharanthine-MIP specifically retained catharanthine and its N-oxide analogue but displayed a weak cross-reactivity for other Vinca alkaloids (vinorelbine, vincristine, vinblastine, vindoline, vinflunine). It appears that the catharanthine-like unit of these molecules are hardly trapped in catharanthine cavities located in the MIP, probably due to the sterical hindrance of the vindoline moiety. Finally, the MIP-SPE applied to C. roseus extract enabled quantitative recovery of catharanthine (101%) and the total removal of vindoline. Its capacity was determined and was equal to 2.43 μmol g(-1). Vindoline is a weaker base than catharanthine, so the vindoline-MIP was achieved with a strong acidic monomer (itaconic acid) to increase vindoline-monomer interactions and a modified washing solvent (ACN-HCOOH 99/1) to reduce non-specific interactions. The influence of the amount of HCOOH (protic modifier) percolated during the washing step upon the elution yield and the imprinting factor for vindoline was investigated. This preliminary optimisation of the washing step, and in particular the number of moles of acid percolated, seems useful to emphasize the use of MIP in conditions of high selectivity or high yield. A compromise was obtained with an imprinting factor equal to 7.6 and an elution recovery of 33%. However MIP-vindoline failed to achieve a specific extraction of vindoline since catharanthine was also extracted probably because of strong non-specific interactions occurring between catharanthine and the sorbent.

Convenient solid phase extraction of cephalosporins in milk using a molecularly imprinted polymer

In this paper, a molecularly imprinted polymer (MIP) for cephalosporin molecules (cephalexin (CFL) and cephapirin (CFP)), was prepared by non covalent molecular imprinting approach and applied to solid phase extraction (SPE). For MIP synthesis, a tributylammonium cefadroxil salt (TBA-CFD) was used as template with methacrylic acid and ethylene glycol dimethacrylate as monomer and cross-linker, respectively, in acetone-methanol 92/8 (v/v) mixture. The selectivity of MIP versus non imprinted polymer (NIP) was confirmed for CFL, CFD and CFP in standard solutions as well as in milk samples. The efficiency of the synthesized MIP was evaluated by means of the application of the proposed MIP-SPE procedure to spiked milk samples previous to the HPLC method for the detection of cephalosporins. The MIP-SPE recoveries were higher than 60% for the three target analytes in spiked milk.

Synthesis of a molecularly imprinted polymer for the solid-phase extraction of betulin and betulinic acid from plane bark.

INTRODUCTION Plant extracts are usually complex mixtures of various polarity compounds and their study often includes a purification step, such as solid-phase extraction (SPE), to isolate interest compounds prior analytical investigations. Molecularly imprinted polymers (MIPs) are a new promising type of SPE material which offer tailor-made selectivity for the extraction of trace active components in complex matrices. Numerous specific cavities that are sterically and chemically complementary of the target molecules, are formed in imprinted polymers. A molecularly imprinted polymer (MIP) was synthesised in order to trap a specific class of triterpene, including betulin and betulinic acid from a methanolic extract of plane bark. METHODOLOGY Imprinted polymers were synthesised by thermal polymerisation of betulin as template, methacrylic acid (MAA) or acrylamide (AA) as functional monomer, ethylene glycol dimethacrylate as crosslinking agent and chloroform as porogen. Afterwards, MAA- and AA-MIPs were compared with their non-imprinted polymers (NIPs) in order to assess the selectivity vs betulin and its derivatives. Recovered triterpenes were analysed by HPLC during MIP-SPE protocol. RESULTS After SPE optimisation, the MAA-imprinted polymer exhibited highest selectivity and recovery (better than 70%) for betulin and best affinity for its structural analogues. Thus, a selective washing step (chloroform, acetonitrile) removed unwanted matrix compounds (fatty acids) from the SPE cartridge. The elution solvent was methanol. Finally, the MAA-MIP was applied to fractionate a plane bark methanolic extract containing betulin and betulinic acid. CONCLUSION This study demonstrated the possibility of direct extraction of betulin and its structural analogues from plant extracts by MIP technology.

Molecularly imprinted polymer dedicated to the extraction of glyphosate in natural waters.

Three molecularly imprinted polymers (MIPs) have been synthesized in order to bind efficiently glyphosate (GLY) in natural waters (mineral and underground). Since the target analyte is polar and hydrophilic, electrostatic interactions and hydrogen bonds have been favored with two templates (phenylphosphonic acid and diethyl(α-aminobenzyl)-phosphonic acid) and two functional monomers (1-allyl-2-thiourea and methacrylic acid). MIPs have been assessed by comparison of the recoveries obtained with MIP and NIP (non imprinted polymer) by solid-phase extraction (SPE). The selectivity of MIP versus NIP was satisfactory for the three imprinted polymers with a very straightforward protocol: conditioning of 250 mg of MIP or NIP packed in 3-mL polypropylene cartridges with 3 mL Milli-Q water, loading of Milli-Q water (15 mL) spiked with 5 mg L(-1) of GLY and its metabolite, aminomethylphosphonic acid (AMPA) and elution by 3 mL NH4OH (10mM) or 3 mL HCl (100mM). SPE fractions were directly analyzed by capillary electrophoresis (CE). Thus, the recoveries of both analytes were greater than 80% for all MIPs and less than 25% for most NIPs. Moreover, the MIP prepared with 1-allyl-2-thiourea as functional monomer and phenylphosphonic acid as template displayed a capacity of 0.033 μmol/mg for GLY. However, the substitution of Milli-Q water by mineral water caused the decrease of MIP recoveries, for that, a pretreatment of the sample by ionic exchange resins was set up and succeeded in improving recoveries (about 50% for GLY and 25% for AMPA). Then, groundwaters were spiked with low concentrations of GLY and AMPA (0.5 μgL(-1)) and directly percolated through MIP cartridges. The extractions were carried out by triplicate and the elution fractions were analyzed by UPLC-MS/MS. The results showed no retention of AMPA but a total retention of GLY by MIP.

Human neutrophil elastase inhibition studied by capillary electrophoresis with laser induced fluorescence detection and microscale thermophoresis.

Capillary electrophoresis-laser induced fluorescence (CZE-LIF) and microscale thermophoresis (MST) were used for the first time to study the inhibition of human neutrophil elastase (HNE). We recently studied HNE kinetics (Km and Vmax) by developing an in-capillary CZE-LIF assay based on transverse diffusion of laminar flow profiles (TDLFP) for reactant mixing. In this work, the former assay was adapted to monitor HNE inhibition. Two natural well known HNE inhibitors from the triterpene family, ursolic acid and oleanolic acid, were tested to validate the developed assay. Since the solubility of pentacyclic triterpenes in aqueous media where the enzymatic reaction will take place is limited, the effect of DMSO and ethanol on HNE was studied using microscale thermophoresis (MST). An agglomeration of the enzyme was revealed when preparing the inhibitor in 5% (v/v) DMSO. This phenomenon did not occur in the presence of ethanol. Therefore, ethanol was used as inhibitor solvent, at a limited percentage of 20% (v/v). In these conditions and after optimization of the TDLFP approach, the repeatability (RSD on migration times and peak-areas inferior to 2.2%) of the CZE-LIF assay and the sensitivity (LOQ of few nM) were found to be satisfactory for conducting inhibition assays. IC50 values for ursolic and oleanolic acid were successfully determined. They were respectively equal to 5.62±0.10μM (r(2)=0.9807; n=3) and to 8.21±0.23μM (r(2)=0.9887; n=3). Excellent agreement was found between the results obtained by CE and those reported in literature which validates the developed method. Particularly, the CE-based assay is able to rank HNE inhibitors relative to each other. Furthermore, MST technique was used for evaluating HNE interaction with the ursolic acid. Up to 16 capillaries were automatically processed to obtain in one titration experiment the dissociation constant for the HNE-ursolic acid complex. Ki was found to be 2.72±0.66μM (n=3) which is in excellent agreement with the value determined by CE enzyme inhibition studies (Ki=2.81μM) confirming the reliability of the developed CE assay and the competitive inhibition mode of ursolic acid.

Coated capillaries with highly charged polyelectrolytes and carbon nanotubes co-aggregated with sodium dodecyl sulphate for the analysis of sulfonylureas by capillary electrophoresis.

Sulfonylureas (SUs) are one of the most widely used herbicides to control weeds in crops. Herein, capillary electrophoresis (CE) was used to determine four sulfonylureas in natural waters, namely chlorsulfuron (CS), iodosulfuron methyl (IM), metsulfuron methyl (MSM) and mesosulfuron methyl (MSS). First of all, a bare silica capillary was chosen with 10mM of 1-butyl-3-methylimidazolium tetrafluoroborate (bminBF4) as electrophoretic buffer (pH 9.6) containing 2 mg L(-1) of surfactant-coated single-wall carbon nanotubes (SC-SWCNTs). A dramatic deviation in migration times was observed. Therefore, a poly(diallyldimethylammonium) chloride (PDADMAC) statically coated cationic capillary was used to improve repeatability and to alter the selectivity of the separation. The electroosmotic flow (EOF) measurement revealed that the SC-SWCNTs were strongly adsorbed at the surface of the PDADMAC coating even in the absence of the surfactant-coated nanotubes in the electrolyte buffer. Consequently, a stable strong cathodic EOF and excellent repeatabilities were obtained with relative standard deviations (RSDs) on migration times and on corrected peak areas below 0.9 and 1.5%, respectively. The separation of the SUs was conducted in only 6 min. No regeneration of the coating between analyses was necessary, and high peak efficiencies up to 173,000 theoretical plates were obtained. The bi-layer coating was subsequently used to analyze sulfonylureas in tap water, in several mineral waters as well as in underground waters spiked with SUs and directly injected into the CE capillary.