Byoung Koun Min

Selective Detection of Acetone and Hydrogen Sulfide for the Diagnosis of Diabetes and Halitosis Using SnO2 Nanofibers Functionalized with Reduced Graphene Oxide Nanosheets

Sensitive detection of acetone and hydrogen sulfide levels in exhaled human breath, serving as breath markers for some diseases such as diabetes and halitosis, may offer useful information for early diagnosis of these diseases. Exhaled breath analyzers using semiconductor metal oxide (SMO) gas sensors have attracted much attention because they offer low cost fabrication, miniaturization, and integration into portable devices for noninvasive medical diagnosis. However, SMO gas sensors often display cross sensitivity to interfering species. Therefore, selective real-time detection of specific disease markers is a major challenge that must be overcome to ensure reliable breath analysis. In this work, we report on highly sensitive and selective acetone and hydrogen sulfide detection achieved by sensitizing electrospun SnO2 nanofibers with reduced graphene oxide (RGO) nanosheets. SnO2 nanofibers mixed with a small amount (0.01 wt %) of RGO nanosheets exhibited sensitive response to hydrogen sulfide (Rair/Rgas = 34 at 5 ppm) at 200 °C, whereas sensitive acetone detection (Rair/Rgas = 10 at 5 ppm) was achieved by increasing the RGO loading to 5 wt % and raising the operation temperature to 350 °C. The detection limit of these sensors is predicted to be as low as 1 ppm for hydrogen sulfide and 100 ppb for acetone, respectively. These concentrations are much lower than in the exhaled breath of healthy people. This demonstrates that optimization of the RGO loading and the operation temperature of RGO-SnO2 nanocomposite gas sensors enables highly sensitive and selective detection of breath markers for the diagnosis of diabetes and halitosis.

Achieving Selective and Efficient Electrocatalytic Activity for CO2 Reduction Using Immobilized Silver Nanoparticles

Selective electrochemical reduction of CO2 is one of the most sought-after processes because of the potential to convert a harmful greenhouse gas to a useful chemical. We have discovered that immobilized Ag nanoparticles supported on carbon exhibit enhanced Faradaic efficiency and a lower overpotential for selective reduction of CO2 to CO. These electrocatalysts were synthesized directly on the carbon support by a facile one-pot method using a cysteamine anchoring agent resulting in controlled monodispersed particle sizes. These synthesized Ag/C electrodes showed improved activities, specifically decrease of the overpotential by 300 mV at 1 mA/cm(2), and 4-fold enhanced CO Faradaic efficiency at -0.75 V vs RHE with the optimal particle size of 5 nm compared to polycrystalline Ag foil. DFT calculations enlightened that the specific interaction between Ag nanoparticle and the anchoring agents modified the catalyst surface to have a selectively higher affinity to the intermediate COOH over CO, which effectively lowers the overpotential.

Surface-Mediated Visible-Light Photo-oxidation on Pure TiO2(001)

We used STM to observe visible light photo-oxidation reactions of formic acid on the ordered lattice-work structure of a TiO(2)(001) surface for the first time. The nanostructured surface makes the band gap significantly smaller than 3.0 eV only at the surface layer, and the surface state of the crystal enables a visible light response.

Embedding covalency into metal catalysts for efficient electrochemical conversion of CO2.

CO2 conversion is an essential technology to develop a sustainable carbon economy for the present and the future. Many studies have focused extensively on the electrochemical conversion of CO2 into various useful chemicals. However, there is not yet a solution of sufficiently high enough efficiency and stability to demonstrate practical applicability. In this work, we use first-principles-based high-throughput screening to propose silver-based catalysts for efficient electrochemical reduction of CO2 to CO while decreasing the overpotential by 0.4-0.5 V. We discovered the covalency-aided electrochemical reaction (CAER) mechanism in which p-block dopants have a major effect on the modulating reaction energetics by imposing partial covalency into the metal catalysts, thereby enhancing their catalytic activity well beyond modulations arising from d-block dopants. In particular, sulfur or arsenic doping can effectively minimize the overpotential with good structural and electrochemical stability. We expect this work to provide useful insights to guide the development of a feasible strategy to overcome the limitations of current technology for electrochemical CO2 conversion.

Synthesis of Cu2ZnSnS4 thin films by a precursor solution paste for thin film solar cell applications

Cu2ZnSnS4 (CZTS) is a very promising semiconductor material when used for the absorber layer of thin film solar cells because it consists of only abundant and inexpensive elements. In addition, a low-cost solution process is applicable to the preparation of CZTS absorber films, which reduces the cost when this film is used for the production of thin film solar cells. To fabricate solution-processed CZTS thin film using an easily scalable and relatively safe method, we suggest a precursor solution paste coating method with a two-step heating process (oxidation and sulfurization). The synthesized CZTS film was observed to be composed of grains of a size of ~300 nm, showing an overall densely packed morphology with some pores and voids. A solar cell device with this film as an absorber layer showed the highest efficiency of 3.02% with an open circuit voltage of 556 mV, a short current density of 13.5 mA/cm(2), and a fill factor of 40.3%. We also noted the existence of Cd moieties and an inhomogeneous Zn distribution in the CZTS film, which may have been triggered by the presence of pores and voids in the CZTS film.

Transient hydroxyl formation from water on oxygen-covered Au(111)

We present evidence for the formation of transient hydroxyls from the reaction of water with atomic oxygen on Au(111) and investigate the effect of adsorbed oxygen on the hydrogen bonding of water. Water is evolved in peaks at 175 and 195 K in temperature programed reaction experiments following adsorption of water on oxygen-covered Au(111). The peak at 175 K is ascribed to sublimation of multilayers of water, whereas the peak at 195 K is associated with oxygen-stabilized water or a water-hydroxyl surface complex. Infrared reflection absorption spectra are consistent with the presence of molecular water over the entire range of coverages studied, indicating that isolated stable hydroxyls are not formed. Isotopic exchange of adsorbed (16)O with H(2)(18)O following adsorption and subsequent temperature programed reaction, however, indicates that transient OH species are formed. The extent of oxygen exchange was considerable--up to 70%. The degree of oxygen exchange depends on the initial coverage of oxygen, the surface temperature when preparing oxygen adatoms, and the H(2)(18)O coverage. The hydroxyls are short-lived, forming and disproportionating multiple times before water desorption during temperature programed reaction. It was also found that chemisorbed oxygen is critical in the formation of hydroxyls and stabilizing water, whereas gold oxide does not contribute to these effects. These results identify transient hydroxyls as species that could play a critical role in oxidative chemical reactions on gold, especially in ambient water vapor. The crystallinity of adsorbed water also depended on the degree of surface ordering and chemical modification based on scanning tunneling microscopy and infrared spectra. These results demonstrate that oxidation of interfaces has a major impact on their interaction with water.

Simple Chemical Solution Deposition of Co3O4 Thin Film Electrocatalyst for Oxygen Evolution Reaction

Oxygen evolution reaction (OER) is the key reaction in electrochemical processes, such as water splitting, metal-air batteries, and solar fuel production. Herein, we developed a facile chemical solution deposition method to prepare a highly active Co3O4 thin film electrode for OER, showing a low overpotential of 377 mV at 10 mA/cm(2) with good stability. An optimal loading of ethyl cellulose additive in a precursor solution was found to be essential for the morphology control and thus its electrocatalytic activity. Our results also show that the distribution of Co3O4 nanoparticle catalysts on the substrate is crucial in enhancing the inherent OER catalytic performance.

A monolithic and standalone solar-fuel device having comparable efficiency to photosynthesis in nature

The need for developing sustainable energy sources has generated academic and industrial attention in artificial photosynthesis, inspired by the natural process. In this study, we demonstrate a highly efficient solar energy to fuel conversion device using CO2 and water as feedstock. We developed a thin film photovoltaic technology for the light absorbing component using a low cost, solution based Cu(InxGa1−x)(SySe1−y)2 (CIGS) module fabrication method to provide sufficient potential for the conversion reactions. Our solar-fuel device uses cobalt oxide (Co3O4) nanoparticle thin film deposited with a low temperature coating method as the water oxidation catalyst and nanostructured gold film as the CO2 reduction to CO generation catalyst. We demonstrated that the integrated monolithic device operated by energy only from sunlight, in an absence of any external energy input. The individual components showed the following abilities: solar-to-power conversion efficiency of 8.58% for the CIGS photovoltaic module photoelectrode, overpotential reduction of water oxidation with the Co3O4 catalyst film by ∼360 mV at 5 mA cm−2, and Faradaic efficiency of over 90% by the nanostructured Au catalyst for CO2 reduction to CO. Remarkably, this is the first demonstration of a monolithic and standalone solar-fuel device whose solar-to-fuel conversion efficiency from CO2 and H2O is 4.23%, which is comparable with that of photosynthesis in nature.

Effect of the Si/TiO2/BiVO4 Heterojunction on the Onset Potential of Photocurrents for Solar Water Oxidation

BiVO4 has been formed into heterojunctions with other metal oxide semiconductors to increase the efficiency for solar water oxidation. Here, we suggest that heterojunction photoanodes of Si and BiVO4 can also increase the efficiency of charge separation and reduce the onset potential of the photocurrent by utilizing the high conduction band edge potential of Si in a dual-absorber system. We found that a thin TiO2 interlayer is required in this structure to realize the suggested photocurrent density enhancement and shifts in onset potential. Si/TiO2/BiVO4 photoanodes showed 1.0 mA/cm(2) at 1.23 V versus the reversible hydrogen electrode (RHE) with 0.11 V (vs RHE) of onset potential, which were a 3.3-fold photocurrent density enhancement and a negative shift in onset potential of 300 mV compared to the performance of FTO/BiVO4 photoanodes.

Silver Nanowire Top Electrodes in Flexible Perovskite Solar Cells using Titanium Metal as Substrate

Flexible perovskite solar cells (FPSCs) have various applications such as wearable electronic textiles and portable devices. In this work, we demonstrate FPSCs on a titanium metal substrate employing solution-processed silver nanowires (Ag NWs) as the top electrode. The Ag NW electrodes were deposited on top of the spiro-MeOTAD hole transport layer by a carefully controlled spray-coating method at moderate temperatures. The power conversion efficiency (PCE) reached 7.45 % under AM 1.5 100 mW cm(-2) illumination. Moreover, the efficiency for titanium-based FPSCs decreased only slightly (by 2.6 % of the initial value) after the devices were bent 100 times. With this and other advances, fully solution-based indium-free flexible photovoltaics, advantageous in terms of price and processing, have the potential to be scaled into commercial production.