Byungrok Lee

Preparation and Characteristics of SiOx Coated Carbon Nanotubes with High Surface Area.

An easy method to synthesize SiOx coated carbon nanotubes (SiOx-CNT) through thermal decomposition of polycarbomethylsilane adsorbed on the surface of CNTs is reported. Physical properties of SiOx-CNT samples depending on various Si contents and synthesis conditions are examined by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), nitrogen isotherm, scanning electron microscope (SEM), and transmission electron microscope (TEM). Morphology of the SiOx-CNT appears to be perfectly identical to that of the pristine CNT. It is confirmed that SiOx is formed in a thin layer of approximately 1 nm thickness over the surface of CNTs. The specific surface area is significantly increased by the coating, because thin layer of SiOx is highly porous. The surface properties such as porosity and thickness of SiOx layers are found to be controlled by SiOx contents and heat treatment conditions. The preparation method in this study is to provide useful nano-hybrid composite materials with multi-functional surface properties.

Methanol-tolerant platinum-palladium catalyst supported on nitrogen-doped carbon Nanofiber for high concentration direct methanol fuel cells

Pt-Pd catalyst supported on nitrogen-doped carbon nanofiber (N-CNF) was prepared and evaluated as a cathode electrode of the direct methanol fuel cell (DMFC). The N-CNF, which was directly synthesized by the catalytic chemical vapor deposition from acetonitrile at 640 °C, was verified as having a change of electrochemical surface properties such as oxygen reduction reaction (ORR) activities and the electrochemical double layer compared with common carbon black (CB). To attain the competitive oxygen reduction reaction activity with methanol tolerance, the Pt and Pd metals were supported on the CB or the N-CNF. The physical and electrochemical characteristics of the N-CNF–supported Pt-Pd catalyst were examined and compared with catalyst supported on the CB. In addition, DMFC single cells using these catalysts as the cathode electrode were applied to obtain I-V polarization curves and constant current operating performances with high-concentration methanol as the fuel. Pt-Pd catalysts had obvious ORR activity even in the presence of methanol. The higher power density was obtained at all the methanol concentrations when it applied to the membrane electrode assembly (MEA) of the DMFC. When the N-CNF is used as the catalyst support material, a better performance with high-concentration methanol is expected.

Pitch-based carbon fibers from coal tar or petroleum residue under the same processing condition

Spinnable pitches and carbon fibers were successfully prepared from petroleum or coal pyrolysis residues. After pyrolysis fuel oil (PFO), slurry oil, and coal tar were simply filtered to eliminate the solid impurities, the characteristics of the raw materials were evaluated by elemental analysis, 13C nuclear magnetic resonance spectrometer, matrix-assisted laser desorption/ionization time-of-flight mass spectrometer (MALDI-TOF-MS), and so on. Spinnable pitches were prepared for melt-spinning carbon fiber through a simple distillation under strong nitrogen flow, and further vacuum distillation to obtain a high softening point. Carbon fibers were produced from the above pitches by single-hole melt spinning and additional heat treatment, for oxidization and carbonization. Even though spinnable pitches and carbon fibers were processed under the same conditions, the melt-spinning and properties of the carbon fiber were different depending on the raw materials. A fine carbon fiber could not be prepared from slurry oil, and the different diameter carbon fibers were produced from the PFO and coal tar pitch. These results seem to be closely correlated with the initial characteristics of the raw materials, under this simple processing condition.

An asymmetrical activated carbon electrode configuration for increased pore utilization in a membrane-assisted capacitive deionization system

Abstract A membrane-assisted capacitive deionization (CDI) system was developed for the purification of water containing sodium chloride using activated carbon fibers (ACFs) as capacitor electrode materials. The ACFs have different degrees of activation with different surface areas and pore size distributions. Their desalination performance for sodium or chloride ions was investigated. Results indicate that the salt removal efficiency and surface area-normalized electrosorption capacity for each ion depend on the surface area, pore depth and the match between the pore sizes of the ACFs and the radius of each hydrated ion. A high surface area and shallow pores favor the salt removal efficiency and a high surface area-normalized electrosorption capacity. The ACF with a median pore size of 0.69 nm performs best for sodium ion removal and those with median pore sizes of 1.09 and 1.52 nm are best for chloride ion removal, which could be ascribed to the fact that the radius of a hydrated sodium ion (0.66 nm) is smaller than that of a hydrated chloride ion (0.72 nm). An asymmetric electrode material configuration is needed to optimize both the anion and cation adsorption in the membrane-assisted CDI system.

Effect of Carbon Felt Oxidation Methods on the Electrode Performance of Vanadium Redox Flow Battery

레독스 흐름 전지의 전극으로 사용하기 위해 탄소펠트를 열처리와 산처리 방법으로 산화 개질하였다. 열중량 분석결과 열처리 또는 산처리에 의하여 탄소펠트의 섬유 표면에 고분자 물질이 제거되고 산소 관능기가 도입된 것을 확인할 수 있었으며 습식 방법인 산처리 방법보다 건식방법인 열처리 방법이 기계적 안정성을 유지하는데 효과적인 처리 방법으로 나타났다. XPS, 원소분석을 통하여 500

Improving the mechanical properties of a high density carbon block from mesocarbon microbeads according to oxidative stabilization

^{\circ}C

Activating needle coke to develop anode catalyst for direct methanol fuel cell

에서 4시간 열처리한 탄소펠트의 표면에 산소 관능기가 부가된 것을 확인하였으며 질소흡착실험에서 거의 없던 표면적이 96

Electrochemical catalytic activity for oxygen reduction reaction of nitrogen-doped carbon nanofibers.

m^2/g

Control of nitrogen content and its effects on the electrochemical behavior of nitrogen-doped carbon nanofibers

로 증가한 것을 알 수 있었다. CV실험 및 분극 실험을 수행한 결과 500

Characteristics of porous carbon nano-fibers synthesized by selective catalytic gasification.

^{\circ}C