C. Gallrapp

Planar pixel sensors for the ATLAS upgrade: beam tests results

The performance of planar silicon pixel sensors, in development for the ATLAS Insertable B-Layer and High Luminosity LHC (HL-LHC) upgrades, has been examined in a series of beam tests at the CERN SPS facilities since 2009. Salient results are reported on the key parameters, including the spatial resolution, the charge collection and the charge sharing between adjacent cells, for different bulk materials and sensor geometries. Measurements are presented for n+-in-n pixel sensors irradiated with a range of fluences and for p-type silicon sensors with various layouts from different vendors. All tested sensors were connected via bump-bonding to the ATLAS Pixel read-out chip. The tests reveal that both n-type and p-type planar sensors are able to collect significant charge even after the lifetime fluence expected at the HL-LHC.

Test beam results of 3D silicon pixel sensors for the ATLAS upgrade

Results on beam tests of 3D silicon pixel sensors aimed at the ATLAS Insertable B-Layer and High Luminosity LHC (HL-LHC) upgrades are presented. Measurements include charge collection, tracking efficiency and charge sharing between pixel cells, as a function of track incident angle, and were performed with and without a 1.6 T magnetic field oriented as the ATLAS inner detector solenoid field. Sensors were bump-bonded to the front-end chip currently used in the ATLAS pixel detector. Full 3D sensors, with electrodes penetrating through the entire wafer thickness and active edge, and double-sided 3D sensors with partially overlapping bias and read-out electrodes were tested and showed comparable performance.

Performance of novel silicon n-in-p planar pixel sensors

The performance of novel n-in-p planar pixel detectors designed for future upgrades of the ATLAS Pixel system is presented. The n-in-p silicon sensors technology is a promising candidate for the pixel upgrade thanks to its radiation hardness and cost effectiveness that allow for enlarging the area instrumented with pixel detectors. The n-in-p modules presented here are composed of pixel sensors produced by CiS connected by bump-bonding to the ATLAS read-out chip FE-I3. The characterization of these devices has been performed before and after irradiation up to a fluence of 5×1015 1 MeV neqcm−2. Charge collection measurements carried out with radioactive sources have proven the functioning of this technology up to these particle fluences. First results from beam test data with a 120 GeV/c pion beam at the CERN-SPS are also discussed, demonstrating a high tracking efficiency of (98.6±0.3)% and a high collected charge of about 10 ke for a device irradiated at the maximum fluence and biased at 1 kV.

Radiation hardness studies of neutron irradiated CMOS sensors fabricated in the ams H18 high voltage process

High voltage CMOS detectors (HVCMOSv3), fabricated in the ams H18 high voltage process, with a substrate resistivity of 10 Ω·cm were irradiated with neutrons up to a fluence of 2×1016 neq/cm2 and characterized using edge-TCT. It was found that, within the measured fluence range, the active region and the collected charge reach a maximum at about 7×1015 neq/cm2 to decrease to the level of the unirradiated detector after 2×1016 neq/cm2.

Charge collection properties of a depleted monolithic active pixel sensor using a HV-SOI process

New pixel detector concepts, based on commercial high voltage and/or high resistivity CMOS processes, are being investigated as a possible candidate to the inner and outer layers of the ATLAS Inner Tracker in the HL-LHC upgrade. A depleted monolithic active pixel sensor on thick film SOI technology is being extensively investigated for that purpose. This particular technology provides a double well structure, which shields the thin gate oxide transistors from the Buried Oxide (BOX). In addition, the distance between transistors and BOX is one order of magnitude bigger than conventional SOI technologies, making the technology promising against its main limitations, as radiation hardness or back gate effects. Its radiation hardness to Total Ionizing Dose (TID) and the absence of back gate effect up to 700 Mrad has been measured and published [1]. The process allows the use of high voltages (up to 300V) which are used to partially deplete the substrate. The process allows fabrication in higher resistivity, therefore a fully depleted substrate could be achieved after thinning. This article shows the results on charge collection properties of the silicon bulk below the BOX by different techniques, in a laboratory with radioactive sources and by edge Transient Current Technique, for unirradiated and irradiated samples.

Novel silicon n-in-p pixel sensors for the future ATLAS upgrades

Abstract In view of the LHC upgrade phases towards HL-LHC the ATLAS experiment plans to upgrade the inner detector with an all silicon system. The n-in-p silicon technology is a promising candidate for the pixel upgrade thanks to its radiation hardness and cost effectiveness that allow for enlarging the area instrumented with pixel detectors. We present the characterization and performance of novel n-in-p planar pixel sensors produced by CiS (Germany) connected by bump bonding to the ATLAS readout chip FE-I3. These results are obtained before and after irradiation up to a fluence of 10 16 1-MeV n eq cm − 2 , and prove the operability of this kind of sensors in the harsh radiation environment foreseen for the pixel system at HL-LHC. We also present an overview of the new pixel production, which is on-going at CiS for sensors compatible with the new ATLAS readout chip FE-I4.

Initial measurements on Pixel Detector modules for the ATLAS upgrades

Sophisticated conditions in terms of peak and integrated luminosity in the Large Hadron Collider (LHC) will raise the ATLAS Pixel Detector to its performance limits. Silicon planar, silicon 3D and diamond pixel sensors are three possible sensor technologies which could be implemented in the upcoming Pixel Detector upgrades of the ATLAS experiment. Measurements of the IV-behavior and measurements with radioactive Americium-241 and Strontium-90 are used to characterize the sensor properties and to understand the interaction between the ATLAS FE-I4 front-end chip and the sensor. Comparisons of results from before and after irradiation, which give a first impression on the charge collection properties of the different sensor technologies are presented.