Carlos Ayala

Determination of losartan, telmisartan, and valsartan by direct injection of human urine into a column-switching liquid chromatographic system with fluorescence detection.

Column-switching high-performance liquid chromatographic (HPLC) method has been developed and validated for quantification of losartan, telmisartan, and valsartan in human urine. Urine samples were diluted on the extraction mobile phase (1:4, v/v) and a volume of 20 microL of this mixture were directly injected onto the HPLC system. The analytes were extracted from the matrix using an on-line solid-phase extraction procedure involving a precolumn packed with 25 microm C(18) alkyl-diol support (ADS), and a solution 2% methanol in 5mM phosphate buffer (pH 3.8) at a flow-rate of 0.8 mL/min for isolation and preconcentration of losartan, telmisartan, and valsartan. The enriched analytes were back-flushed after, onto the analytical column with a mixture of 5mM phosphate buffer (pH 3.8)-acetonitrile-methanol (65:20:15, v/v/v) at a flow-rate of 3.0 mL/min and detected by fluorescence at 259 and 399 nm as excitation and emission wavelength respectively. The separation of losartan, telmisartan, and valsartan was achieved on a Chromolith RP-18e monolithic column. The method provides extraction recoveries from spiked urine samples greater than 93%. Intra-day and inter-day precision were generally acceptable; the intra-day-assay C.V. was <3.5 for all compounds and the inter-day-assay C.V. was < 3.7%. The estimated calibration range was 0.001-2.5 microg/mL(-1) with excellent coefficient of determination (>0.9981). The detection limits for losartan, telmisartan, and valsartan at a signal-to-noise ratio of 5:1 were 0.002, 0.0002 and 0.001 microg/mL(-1) when a sample volume of 20 microL was injected. The proposed method permitted the simultaneous determination of losartan, telmisartan, and valsartan in 8 min, with an adequate precision and sensitivity. However, the overlap of the sample cleanup step with the analysis increases the sampling frequency to 12 samples/h. The developed column-switching method was successfully applied for the determination of these analytes in human urine samples of patients submitted at ARA-IIs therapy.

A simple strategy for determining ethanol in all types of alcoholic beverages based on its on-line liquid-liquid extraction with chloroform, using a flow injection system and Fourier transform infrared spectrometric detection in the mid-IR

In this work, a simple strategy for the determination of ethanol in all types of alcoholic beverages using Fourier transform infrared spectrometric detection has been developed. The methodological proposal includes the quantitative on-line liquid-liquid extraction of ethanol with chloroform, through a sandwich type cell equipped with a PTFE membrane, using a two-channel manifold; and direct measurement of the analyte in the organic phase, by means of Fourier transform infrared spectrometry. The quantification was carried out measuring the ethanol absorbance at 877cm(-1)(,) corrected by means of a baseline established between 844 and 929cm(-1). The procedure, which does not require any sample pretreatment (except for the simple degassing of beer and gassy wine samples, and a simple dilution of spirits with water), was applied to determine ethanol in different alcoholic beverages such as beers, wines and spirits. The results obtained highly agree with those obtained by a derivative FTIR spectrometric procedure, and by head space-gas chromatography with FID detection. The proposed method is simple, fast, precise and accurate. Moreover, it can be easily adapted to any infrared spectrometer equipped with a standard transmission IR cell, and provides attractive analytical features, which are comparable to, or better than those offered by other published methods. In consequence, it represents a valid alternative for the determination of ethanol in alcoholic beverages, and could be suitable for the routine control analysis.

Flow analysis-hydride generation-Fourier transform infrared spectrometric determination of antimony in pharmaceuticals.

In this work, a flow analysis system with hydride generation and Fourier transform infrared (FTIR) spectrometric detection has been developed for the determination of antimony in pharmaceuticals. The method is based on the on-line mineralization/oxidation of the organic antimonials present in the sample and pre-reduction of Sb(V) to Sb(III) with K(2)S(2)O(8) and KI, respectively; prior to the stibine generation. The gaseous SbH(3) is separated from the solution in a gas phase separator, and transported by means of a nitrogen carrier into a short pathway (10 cm) IR gas cell, where the corresponding FTIR spectrum is acquired by accumulating 3 scans in a continuous mode. The 1893 cm(-1) band was used for the quantification of the antimony. The procedure is carried out in a closed system, which reduces sample handling and makes possible the complete automation of the antimony determination. The figures of merit of the proposed method (linear range: 0-600 mg l(-1), limit of detection (3sigma)=0.9 mg l(-1), limit of quantification (10sigma)=3 mg Sb l(-1), precision (R.S.D.) less than 1% and sample frequency=28 h(-1)), are appropriate for the designed application. Furthermore, precise and accurate results were found for the analysis of different antimonial pharmaceutical samples, indicating that the methodology developed represents a valid alternative for the determination of antimony in pharmaceuticals, which could be suitable for the routine control analysis.

Analysis of cocaine and benzoylecgonine in urine by using multisyringe flow injection analysis-gas chromatography-mass spectrometry system.

In this paper, a method was described to determine cocaine (COC) and benzoylecgonine (BZE) in human urine samples by GC-MS detection. The extraction of analytes from urine samples was achieved in an Oasis hydrophilic-lipophilic balance column (20 mmx3.9 mm id, dp=25 microm; Waters, USA), incorporated in a multisyringe flow injection system, used for the sample treatment. Finally, to improve the volatility of the BZE, an in-line derivatization reaction with N,O-bis (trimethylsilyl) trifluoroacetamide with 1% trimethylchlorosilane was made microwave-assisted in order to reduce the reaction time. The results showed that the proposed method is a good alternative for the analysis of COC and BZE in urine samples because it offers advantages compared with those described in the literature, which include simplicity in the sample treatment, the sensitivity and selectivity necessary to determine the analytes of interest at low levels in the urine and high sample throughput.

Flow analysis–vapor phase generation–Fourier transform infrared (FA–VPG–FTIR) spectrometric determination of nitrite☆

In this work, the coupling between flow analysis (FA)-vapor phase generation (VPG) and Fourier transform infrared spectrometry (FTIR) has been proposed as a novel and alternative strategy for the determination of nitrite. The analyte was transformed into the gaseous nitric oxide (NO) by on-line reaction with potassium iodide (KI) or ascorbic acid in acidic medium. The gaseous NO generated was transported by means of a N(2) gas carrier stream inside the IR gas cell and the corresponding FTIR spectrum was acquired in a continuous mode. The absorbance at 1876cm(-1), corrected by a baseline established between 1879 and 1872cm(-1) at a nominal resolution of 2cm(-1), was selected as a measurement criterion. The effect of different spectroscopic and flow analysis experimental parameters, such as nominal resolution, number of scans, reducing agent and its concentration, acidic medium, reagents and sample flow rates, and the carrier gas flow rate on the analytical signal, and then in the figures of merit were initially evaluated by using a standard short path length (10cm) IR gas cell. The optimization of the system was carried out by the univariate method. The main aims of this study were: (i) to investigate the on-line generation of gaseous nitric oxide in a continuous flow system, and (ii) the use of Fourier transform infrared spectrometry as an alternative and selective detector for the determination of nitrite. The proposed method was initially tested and applied for the determination of nitrite in samples with very high concentration of nitrite, such as frankfurters.

Flow analysis–hydride generation–Fourier transform infrared spectrometry. A new analytical technique for the simultaneous determination of antimony, arsenic and tin

The combination of flow analysis (FA), hydride generation (HG) and Fourier transform infrared (FTIR) spectrometry is proposed as a novel and powerful analytical technique for the individual and simultaneous determination of antimony, arsenic and tin in aqueous samples. The analytes were transformed into the volatile hydride form by on-line reaction with sodium tetrahydroborate in acidic medium. The gaseous analyte hydrides [M(n)H(m), (g)] generated, were transported by means of a carrier gas stream inside the IR gas cell and the corresponding FTIR spectrum was acquired in a continuous mode. The 1893, 1904 and 2115 cm(-1) bands of the SbH3, SnH4, and AsH3 were selected for the determination of antimony, tin and arsenic, respectively. The limit of detection (3sigma) obtained by using a short-path (10 cm) IR gas cell were 0.25, 0.30 and 1.2 mg l(-1) for the determination of antimony, tin and arsenic, respectively; while the precision (relative standard deviation, RSD, n 5) found from a standard solution containing 50 mg l(-1) of each element was, in all cases, less than 0.3%. However, the use of a long-path (7.25 m) IR gas cell improved the figures of merit (sensitivity, limits of detection and quantification) nearly 60-fold. The effect of the main experimental and instrumental variables, such as acidic media, sodium tetraborohydrate concentration, nitrogen flow rate, nominal resolution and the scan accumulation on the analytical signals of the antimony, tin and arsenic hydrides, were studied. Further, the potential of the proposed technique for the simultaneous determination of these elements was tested, analyzing synthetic samples containing different amounts of Sb, Sn and As.

Development of a MSFIA sample treatment system as front end of GC-MS for atenolol and propranolol determination in human plasma.

An on-line solid-phase extraction (SPE) method coupled to gas chromatography-mass spectrometry (GC-MS) has been developed for the determination of atenolol (ATN) and propranolol (PRO) in human plasma. The hyphenation of SPE with multisyringe flow injection analysis (MSFIA) allows the simultaneous GC-MS determination of ATN and PRO with high selectivity and sensitivity. On-line preconcentration and derivatisation of the analytes were carried out by means of using restricted access materials (RAM) and microwave (MW) assisted derivatisation reactions with N-methyl-N-(trimethylsilyl) trifluoroacetamide (MSTFA)+1% trimethylchlorosilane (TMCS). Multivariate optimization was applied to optimize experimental conditions. The whole procedure comprising sample pretreatment and analyte determination took about 15 min. However, the overlap of the automatic sample treatment with the GC separation increased the frequency to 7 samples h(-1). The validated method was successfully applied to direct ATN and PRO determination in human plasma.

Reagent-free determination of amikacin content in amikacin sulfate injections by FTIR derivative spectroscopy in a continuous flow system

The quantitative estimation of amikacin (AMK) in AMK sulfate injection samples is reported using FTIR-derivative spectrometric method in a continuous flow system. Fourier transform of mid-IR spectra were recorded without any sample pretreatment. A good linear calibration (r>0.999, %RSD<2.0) in the range of 7.7–77.0 mg/mL was found. The results showed a good correlation with the manufacturers and overall they all fell within acceptable limits of most pharmacopoeial monographs on AMK sulfate.