Chiara Giosuè

Assessment of air pollutant sources in the deposit on monuments by multivariate analysis.

A proper recognition of the pollutant sources in atmospheric deposit is a key problem for any action aiming at reducing their emission, being this an important issue with implications both on human health safeguard and on the cultural heritage conservation in urban sites. This work presents the results of a statistical approach application for the identification of pollutant sources in deposits and damage layers on monuments located in different European sites: Santa Maria del Fiore, Florence (Italy), Cologne Cathedral, Cologne (Germany), Ancient ramparts, Salè (Morocco), National Museum, Cracow (Poland) and National Gallery, Oslo (Norway). For this aim, the surface damage layers on monuments and historical buildings of the selected sites were collected and analyzed, in terms of ionic and elemental composition, through application of ion chromatography and induced coupled plasma-optical emission spectroscopy. The achieved results were processed by multivariate analyses such as correlation matrix and principal component analysis in order to identify the possible origin of pollutants affecting the state of conservation of the monuments. This allowed us to assume that in all case studies the traffic emission is the main pollutant source. In the case of Ancient ramparts, Salè (Morocco), and National Gallery, Oslo (Norway), the surfaces are also under influence of marine aerosols. Moreover, concerning the Cologne Cathedral, the strong impact of the pollutants emitted by railway station was also revealed.

Durability assessment to environmental impact of nano-structured consolidants on Carrara marble by field exposure tests.

The EU policy of reducing the emissions of combustion generated pollutants entails climate induced deterioration to become more important. Moreover, products applied to preserve outdoor built heritage and their preliminary performance tests often turn out to be improper. In such context, the paper reports the outcomes of the methodology adopted to assess the durability and efficiency of nano-based consolidating products utilized for the conservation of carbonate artworks, performing field exposure tests on Carrara marble model samples in different sites in the framework of the EC Project NANOMATCH. Surface properties and cohesion, extent and penetration of the conservative products and their interactions with marble substrates and environmental conditions are here examined after outdoor exposure for eleven months in four different European cities and compared with the features of undamaged and of untreated damaged specimens undergoing the same exposure settings.

Influence of Binders and Lightweight Aggregates on the Properties of Cementitious Mortars: From Traditional Requirements to Indoor Air Quality Improvement

Innovative and multifunctional mortars for renders and panels were manufactured using white photocatalytic and non-photocatalytic cement as binder. Unconventional aggregates, based on lightweight materials with high specific surface and adsorbent properties, were adopted in order to investigate the possible ability to passively improve indoor air quality. The reference mortar was manufactured with traditional calcareous sand. Results show that even if the mechanical properties of mortars with unconventional aggregates generally decrease, they remain acceptable for application as render. The innovative mortars were able to passively improve indoor air quality in terms of transpirability (70% higher), moisture buffering ability (65% higher) and depolluting capacity (up to 75% higher) compared to traditional ones under the current test conditions.

Appraisal of a hybrid air cleaning process

Nowadays, there is an amplified interest in maintaining suitable indoor air quality (IAQ). Besides a wide range of available interventions, air cleaners are considered a valuable tool, since based on inexpensive and easily implementing technologies to improve IAQ. The purpose of this work is to combine the TiO2-photocatalysis with the electrostatic and adsorption processes, in order to improve efficiency and reliability. A TiO2-photocatalytic oxidation combined with an electrostatic filter has been studied. Nitrogen oxides reduction and degradation of many VOC over different catalyst support were monitored jointly with CO and CO2 production. The coupling of photocatalysis with an external electric field enhances efficiency of the process. The choice of materials with diversified adsorptive characteristics plays an important role in the durability of the process over time.

Binders alternative to Portland cement and waste management for sustainable construction—part 1:

This review presents “a state of the art” report on sustainability in construction materials. The authors propose different solutions to make the concrete industry more environmentally friendly in order to reduce greenhouse gases emissions and consumption of non-renewable resources. Part 1—the present paper—focuses on the use of binders alternative to Portland cement, including sulfoaluminate cements, alkali-activated materials, and geopolymers. Part 2 will be dedicated to traditional Portland-free binders and waste management and recycling in mortar and concrete production.

Valorisation of GRP Dust Waste in Fired Clay Bricks

In Europe, the total amount of Glass Reinforced Plastic (GRP) waste is increasing. In order to valorise GRP dust (GRPd) waste and to reduce the consumption of nonrenewable resources in building materials, GRPd has been already investigated in cementitious materials where it gives even an improvement in some performances of the final products. Valorisation of GRPd waste in the production of bricks can be considered as a further alternative. In this paper, GRPd waste was substituted to the clay volume at 5% and 10% for the manufacturing of fired clay bricks. All specimens were subjected to a firing temperature of 850°C for 6 hours, then tested and compared in terms of porosity, compressive and flexural strengths, density, and water absorption. Despite a decrease in compressive strength up to 46% with 10% of GRPd substitution and an increase of water absorption from 14% to 29% with 5% and 10% of GRPd substitution, respectively, an increase in terms of lightness (about 10%), maximum flexural strength (up to 31%), and deflections at the maximum load (up to 130%) has been registered by specimens with 10% of GRPd substitution.

Bricks and Concrete Wastes as Coarse and Fine Aggregates in Sustainable Mortars

The total substitution by volume of natural coarse calcareous aggregate by coarse recycled brick aggregate (RBA) and coarse recycled concrete aggregate (RCA) has been investigated to produce more sustainable and environment-friendly mortars. Aggregates were also partially substituted by their fines at 12.5% by volume. Mortars have been tested in terms of mechanical, microstructural, and durability properties. Results show that it is feasible to replace a natural calcareous aggregate entirely by recycled aggregates. In particular, the obtained mortars, even if more porous and more prone to the water capillary absorption than that manufactured with natural aggregates, result in less stiffness and thus are less subjected to crack formation, more permeable to water vapour, and less susceptible to sulphate attack.

Stainless and Galvanized Steel, Hydrophobic Admixture and Flexible Polymer-Cement Coating Compared in Increasing Durability of Reinforced Concrete Structures

The use of stainless or galvanized steel reinforcements, a hydrophobic admixture or a flexible polymer-cement coating were compared as methods to improve the corrosion resistance of sound or cracked reinforced concrete specimens exposed to chloride rich solutions. The results show that in full immersion condition, negligible corrosion rates were detected in all cracked specimens, except those treated with the flexible polymer-cement mortar as preventive method against corrosion and the hydrophobic concrete specimens. High corrosion rates were measured in all cracked specimens exposed to wet-dry cycles, except for those reinforced with stainless steel, those treated with the flexible polymer-cement coating as restorative method against reinforcement corrosion and for hydrophobic concrete specimens reinforced with galvanized steel reinforcements.

Non-Destructive Testing for the In Situ Assessment of the Ionic Flux in Cementitious Materials

The study deals with the design, calibration and testing of a diffusive sampling probe for in situ assessment of ion mobility in binder-based matrix. In parallel, leaching texts were conducted to compare the ions release obtained under equilibrium condition with the dynamic flux induced by the diffusive sampling probe. The probe contains an ionic exchange resin that acts as sink, causing a re-supply of ions from the solid to the solution phase, and inducing diffusion fluxes from the mortar through a thin diffusion chamber. The flux depends on the quantity of mobile ions in the solid phase and on the exchanging rate from solid phase to solution. By means of the in situ sampling with this diffusive probe, information about the interaction of materials with the environment can be obtained. This information is very useful for the environmental impact assessment of the material and its durability.