Christelle Despas

Investigation of alendronate-doped Apatitic Cements as a Potential Technology for the Prevention of Osteoporotic Hip Fractures: Critical Influence of the Drug Introduction Mode on the In Vitro Cement Properties.

Combination of a bisphosphonate (BP) anti-osteoporotic drug, alendronate, with an apatitic calcium phosphate cement does not significantly affect the main properties of the biomaterial, in terms of injectability and setting time, provided that the BP is introduced chemisorbed onto calcium-deficient apatite, one of the components of the cement. In contrast to other modes of introducing the BP into the cement formulation, this mode allows to minimize alendronate release in the cement paste, thus limiting the setting retardant effect of the BP. An original approach based on high frequency impedance measurements is found to be a convenient method for in situ monitoring of the cement setting reaction. The release profile of the drug from a cement block under continuous flow conditions can be well described using a coupled chemistry/transport model, under simulated in vivo conditions. The results show that the released alendronate concentration is expected to be much lower than the cytotoxic concentration.

Abiotic Process for Fe(II) Oxidation and Green Rust Mineralization Driven by a Heterotrophic Nitrate Reducing Bacteria (Klebsiella mobilis)

Green rusts (GRs) are mixed Fe(II)-Fe(III) hydroxides with a high reactivity toward organic and inorganic pollutants. GRs can be produced from ferric reducing or ferrous oxidizing bacterial activities. In this study, we investigated the capability of Klebsiella mobilis to produce iron minerals in the presence of nitrate and ferrous iron. This bacterium is well-known to reduce nitrate using an organic carbon source as electron donor but is unable to enzymatically oxidize Fe(II) species. During incubation, GR formation occurred as a secondary iron mineral precipitating on cell surfaces, resulting from Fe(II) oxidation by nitrite produced via bacterial respiration of nitrate. For the first time, we demonstrate GR formation by indirect microbial oxidation of Fe(II) (i.e., a combination of biotic/abiotic processes). These results therefore suggest that nitrate-reducing bacteria can potentially contribute to the formation of GR in natural environments. In addition, the chemical reduction of nitrite to ammonium by GR is observed, which gradually turns the GR into the end-product goethite. The nitrogen mass-balance clearly demonstrates that the total amount of ammonium produced corresponds to the quantity of bioreduced nitrate. These findings demonstrate how the activity of nitrate-reducing bacteria in ferrous environments may provide a direct link between the biogeochemical cycles of nitrogen and iron.

High-frequency impedance measurement as a relevant tool for monitoring the apatitic cement setting reaction

This work reports the development of a relevant and general method based on high frequency impedance measurements, for the in situ monitoring of the alpha-tricalcium phosphate (α-TCP) to calcium-deficient hydroxyapatite (CDA) transformation which is the driving force of the hardening processes of some calcium phosphate cements (CPC) used as bone substitutes. The three main steps of the setting reaction are identified in a non invasive way through the variation of dielectric permittivity and dielectric losses. The method is also likely to characterize the effect of the incorporation of additives (i.e, antiosteoporotic bisphosphonate drugs such as Alendronate) in the CPC formulation on the hydration process. It allows not only to confirm the retarding effect of bisphosphonate by an accurate determination of setting times, but also to assess the phenomena taking place whether alendronate is added in the liquid phase or combined to the solid phase of the cement composition. Compared to the conventional Gillmore needle test, the present method offers the advantage of accurate, user-independent, in situ and real-time determination of the initial and final times of the chemical hardening process, which are important parameters when considering surgical applications.

Sorption of polluting metal ions on a palm tree frond sawdust studied by the means of modified carbon paste electrodes.

Water remediation by adsorption of the metal ions on a low cost sorbent is the frame of the present study. The metal ions adsorption properties of sawdust of palm tree fronds (PTF sawdust) are investigated by both equilibrium measurements and modified carbon paste electrode. The ability to adsorb Cu(II), Cr(VI) and As(III) in significant quantities is demonstrated. Carbon paste electrodes modified by incorporation of PTF sawdust (PTF-CPE) or, for comparison, an organically modified silica for the detection of copper(II) are investigated in term of sensitivity, estimation of number of possible reuses, repeatability and interference effect. A detection limit for Cu(II) analysis of 1.0×10(-8) M has been achieved after 5 min preconcentration and a single PTF-CPE can be used for up to 10 preconcentration-analysis-regeneration cycles. The relative standard deviation (n=9) for the determination of a 10(-6) M Cu(II) solution (pH=5) was about 26%. The effects of Ca(II), As(III) and Cr(VI) on the copper detection are investigated: calcium ions were shown to compete with copper on the same adsorption sites, arsenic(III) has no effect on the copper detection whereas chromium(VI) was shown to enhance the copper detection.

Mesoporous Silica Thin Films for Improved Electrochemical Detection of Paraquat

An electrochemical method was developed for rapid and sensitive detection of the herbicide paraquat in aqueous samples using mesoporous silica thin film modified glassy carbon electrodes (GCE). Vertically aligned mesoporous silica thin films were deposited onto GCE by electrochemically assisted self-assembly (EASA). Cyclic voltammetry revealed effective response to the cationic analyte (while rejecting anions) thanks to the charge selectivity exhibited by the negatively charged mesoporous channels. Square wave voltametry (SWV) was then used to detect paraquat via its one electron reduction process. Influence of various experimental parameters (i.e., pH, electrolyte concentration, and nature of electrolyte anions) on sensitivity was investigated and discussed with respect to the mesopore characteristics and accumulation efficiency, pointing out the key role of charge distribution in such confined spaces on these processes. Calibration plots for paraquat concentration ranging from 10 nM to 10 μM were constructed at mesoporous silica modified GCE which were linear with increasing paraquat concentration, showing dramatically enhanced sensitivity (almost 30 times) as compared to nonmodified electrodes. Finally, real samples from Meuse River (France) spiked with paraquat, without any pretreatment (except filtration), were analyzed by SWV, revealing the possible detection of paraquat at very low concentration (10-50 nM). Limit of detection (LOD) calculated from real sample analysis was found to be 12 nM, which is well below the permissible limits of paraquat in drinking water (40-400 nM) in various countries.

One pot synthesis of ordered mesoporous organosilica particles bearing propyl-, octyl- and hexadecyl-chains

New hybrid organic–inorganic materials exhibiting ordered mesoporous structures have been synthesized by co-condensation of tetraethoxysilane and various alkyltrimethoxysilanes with increasing length of the hydrocarbon chain (propyl, octyl, hexadecyl), in water–ethanol solution containing ammonia, in the presence of a cationic surfactant (cetyltrimethylammonium bromide) as templating agent. The obtained hybrid materials were characterized by using several physico-chemical techniques, such as X-ray diffraction, N2 adsorption, 29Si MAS NMR, SEM and elemental analysis. It was shown that the direct synthesis procedure allows obtaining ordered hybrid mesoporous silica with various contents of organic functions, from 5 to 20xa0%. Moreover, increasing the chain length of the organic group, from propyl to octyl and hexadecyl leads to a change of the pore structure from hexagonal p6mm MCM-41 type architecture to cubic Ia3d MCM-48 type mesostructure.

Design and properties of a novel radiopaque injectable apatitic calcium phosphate cement, suitable for image-guided implantation: DESIGN AND PROPERTIES OF A NOVEL RADIOPAQUE INJECTABLE APATITIC CPC

An injectable purely apatitic calcium phosphate cement (CPC) was successfully combined to a water-soluble radiopaque agent (i.e., Xenetix® ), to result in an optimized composition that was found to be as satisfactory as poly(methyl methacrylate) (PMMA) formulations used for vertebroplasty, in terms of radiopacity, texture and injectability. For that purpose, the Xenetix dosage in the cement paste was optimized by injection of the radiopaque CPC in human cadaveric vertebrae under classical PMMA vertebroplasty conditions, performed by interventional radiologists familiar with this surgical procedure. When present in the cement paste up to 70 mg I mL-1 , Xenetix did not influence the injectability, cohesion, and setting time of the resulting composite. After hardening of the material, the same observation was made regarding the microstructure, mechanical strength and alpha-tricalcium phosphate to calcium deficient apatite transformation rate. Upon implantation in bone in a small animal model (rat), the biocompatibility of the Xenetix-containing CPC was evidenced. Moreover, an almost quantitative release of the contrast agent was found to occur rapidly, on the basis of in vitro static and dynamic quantitative studies simulating in vivo implantation.

Preparation of ordered and oriented mesoporous silica thin films bearing octyl or hexadecyl groups by electrochemically assisted self-assembly and evaluation of their transport properties

Well-organized octyl- and hexadecyl-functionalized mesoporous silica thin films are generated onto indium-tin oxide electrodes by combining the electrochemically assisted self-assembly technique and the sol–gel co-condensation route. The electrodeposition is carried out under potential control from mixtures containing various molar ratios of tetraethoxysilane and octyltrimethoxysilane (O-TES) or hexadecyltrimethoxysilane (HD-TES), using cetyltrimethylammonium bromide as surfactant template. Films with hexagonally packed functionalized mesochannels oriented perpendicular to the underlying support are obtained up to, respectively, 20xa0% O-TES and 5xa0% HD-TES introduced in the starting sol. Electrochemical investigations using various redox probes demonstrate that the films remain porous despite the presence of long carbon chains inside the mesochannels and that, in the presence of such long chain alkyl groups, the physical diffusion through the pores is not sufficient to describe the mass transport issues, which can also imply accumulation effects owing to the hydrophobic character of the medium.

A straightforward approach to enhance the textural, mechanical and biological properties of injectable calcium phosphate apatitic cements (CPCs): CPC/blood composites, a comprehensive study

Two commercial formulations of apatitic calcium phosphate cements (CPCs), Graftys® Quickset (QS) and Graftys® HBS (HBS), similar in composition but with different initial setting time (7 and 15min, respectively), were combined to ovine whole blood. Surprisingly, although a very cohesive paste was obtained after a few minutes, the setting time of the HBS/blood composite dramatically delayed when compared to its QS analogue and the two blood-free references. Using solid state NMR, scanning electron microscopy and high frequency impedance measurements, it was shown that, in the particular case of the HBS/blood composite, formation of a reticulated and porous organic network occurred in the intergranular space, prior to the precipitation of apatite crystals driven by the cement setting process. The resulting microstructure conferred unique biological properties to this material upon implantation in bone defects, since its degradation rate after 4 and 12weeks was more than twice that for the three other CPCs, with a significant replacement by newly formed bone.nnnSTATEMENT OF SIGNIFICANCEnA major challenge in the design of bone graft substitutes is the development of injectable, cohesive, resorbable and self-setting calcium phosphate cement (CPC) that enables rapid cell invasion with initial mechanical properties as close as bone ones. Thus, we describe specific conditions in CPC-blood composites where the formation of a 3D clot-like network can interact with the precipitated apatite crystals formed during the cement setting process. The resulting microstructure appears more ductile at short-term and more sensitive to biological degradation which finally promotes new bone formation. This important and original paper reports the design and in-depth chemical and physical characterization of this groundbreaking technology.