Christoph M. Schumacher

Thermoresponsive Polymer Induced Sweating Surfaces as an Efficient Way to Passively Cool Buildings

Buildings can be effectively cooled by a bioinspired sweating-like action based on thermoresponsive hydrogels (PNIPAM), which press out their stored water when exceeding the lower critical solution temperature. The surface temperature is reduced by 15 °C compared to that of a conventional hydrogel (pHEMA) and by 25 °C compared to the bare ground.

Effects of flame made zinc oxide particles in human lung cells - a comparison of aerosol and suspension exposures.

BackgroundPredominantly, studies of nanoparticle (NPs) toxicology in vitro are based upon the exposure of submerged cell cultures to particle suspensions. Such an approach however, does not reflect particle inhalation. As a more realistic simulation of such a scenario, efforts were made towards direct delivery of aerosols to air-liquid-interface cultivated cell cultures by the use of aerosol exposure systems.This study aims to provide a direct comparison of the effects of zinc oxide (ZnO) NPs when delivered as either an aerosol, or in suspension to a triple cell co-culture model of the epithelial airway barrier. To ensure dose–equivalence, ZnO-deposition was determined in each exposure scenario by atomic absorption spectroscopy. Biological endpoints being investigated after 4 or 24h incubation include cytotoxicity, total reduced glutathione, induction of antioxidative genes such as heme-oxygenase 1 (HO–1) as well as the release of the (pro)-inflammatory cytokine TNFα.ResultsOff-gases released as by-product of flame ZnO synthesis caused a significant decrease of total reduced GSH and induced further the release of the cytokine TNFα, demonstrating the influence of the gas phase on aerosol toxicology. No direct effects could be attributed to ZnO particles. By performing suspension exposure to avoid the factor “flame-gases”, particle specific effects become apparent. Other parameters such as LDH and HO–1 were not influenced by gaseous compounds: Following aerosol exposure, LDH levels appeared elevated at both timepoints and the HO–1 transcript correlated positively with deposited ZnO-dose. Under submerged conditions, the HO–1 induction scheme deviated for 4 and 24h and increased extracellular LDH was found following 24h exposure.ConclusionIn the current study, aerosol and suspension-exposure has been compared by exposing cell cultures to equivalent amounts of ZnO. Both exposure strategies differ fundamentally in their dose–response pattern. Additional differences can be found for the factor time: In the aerosol scenario, parameters tend to their maximum already after 4h of exposure, whereas under submerged conditions, effects appear most pronounced mainly after 24h. Aerosol exposure provides information about the synergistic interplay of gaseous and particulate phase of an aerosol in the context of inhalation toxicology. Exposure to suspensions represents a valuable complementary method and allows investigations on particle-associated toxicity by excluding all gas–derived effects.

Combining Phosphate and Bacteria Removal on Chemically Active Filter Membranes Allows Prolonged Storage of Drinking Water

A chemically active filtration membrane with incorporated lanthanum oxide nanoparticles enables the removal of bacteria and phosphate at the same time and thus provides a simple device for preparation of drinking water and subsequent safe storage without using any kind of disinfectants.

Nanomagnet-based removal of lead and digoxin from living rats

In a number of clinical conditions such as intoxication, bacteraemia or autoimmune diseases the removal of the disease-causing factor from blood would be the most direct cure. However, physicochemical characteristics of the target compounds limit the applicability of classical filtration and diffusion-based processes. In this work, we present a first in vivo magnetic blood purification rodent animal model and demonstrate its ability to rapidly clear toxins from blood circulation using two model toxins with stable plasma levels (lead (Pb(2+)) and digoxin). Ultra-strong functionalized metal nanomagnets are employed to eliminate the toxin from whole blood in an extracorporeal circuit. In the present experimental demonstration over 40% of the toxin (i.e. lead or digoxin) was removed within the first 10 minutes and over 75% within 40 minutes. After capturing the target substance, a magnetic trap prevents the toxin-loaded nanoparticles from entering the blood circulation. Elemental analysis and magnetic hysteresis measurements confirm full particle recovery by simple magnetic separation (residual particle concentration below 1 μg mL(-1) (detection limit)). We demonstrate that magnetic separation-based blood purification offers rapid blood cleaning from noxious agents, germs or other deleterious materials with relevance to a number of clinical conditions. Based on this new approach, current blood purification technologies can be extended to efficiently remove disease-causing factors, e.g. overdosed drugs, bacteria or cancer cells without being limited by filter cut-offs or column surface saturation.

Endotoxin Removal by Magnetic Separation-Based Blood Purification

This work describes a magnetic separation-based approach using polymyxin B-functionalized metal alloy nanomagnets for the rapid elimination of endotoxins from human blood in vitro and functional assays to evaluate the biological relevance of the blood purification process. Playing a central role in gram-negative sepsis, bacteria-derived endotoxins are attractive therapeutic targets. However, both direct endotoxin detection in and removal from protein-rich fluids remains challenging. We present the synthesis and functionalization of ultra-magnetic cobalt/iron alloy nanoparticles and a magnetic separation-based approach using polymyxin B-functionalized nanomagnets to remove endotoxin from human blood in vitro. Conventional chromogenic Limulus Amebocyte Lysate assays confirm decreased endotoxin activity in purified compared to untreated samples. Functional assays assessing key steps in host defense against bacteria show an attenuated inflammatory mediator expression from human primary endothelial cells in response to purified blood samples compared to untreated blood and less chemotactic activity. Exposing Escherichia coli-positive blood samples to polymyxin B-functionalized nanomagnets even impairs the ability of gram-negative bacteria to form colony forming units, thus making magnetic separation based blood purification a promising new approach for future sepsis treatment.

3D printed lost-wax casted soft silicone monoblocks enable heart-inspired pumping by internal combustion

We present a gas combustion powered soft pump made from highly durable and flexible polydimethylsiloxane (soft silicone). Our soft pump was able to run for 10 000 combustion cycles at a constant combustion power rating of 500 watts and thus discloses novel prospects for long-lasting soft-machines at high specific energy-densities.

Template-Particle Stabilized Bicontinuous Emulsion Yielding Controlled Assembly of Hierarchical High-Flux Filtration Membranes

A novel solvent-evaporation-based process that exploits template-particle stabilized bicontinuous emulsions for the formation of previously unreached membrane morphologies is reported in this article. Porous membranes have a wide range of applications spanning from water filtration, pharmaceutical purification, and battery separators to scaffolds for tissue engineering. Different situations require different membrane morphologies including various pore sizes and pore gradients. However, most of the previously reported membrane preparation procedures are restricted to specific morphologies and morphology alterations require an extensive optimization process. The tertiary system presented in this article, which consists of a poly(ether sulfone)/dimethylacetamide (PES/DMAc) solution, glycerol, and ZnO-nanoparticles, allows simple and exact tuning of pore diameters ranging from sub-20 nm, up to 100 nm. At the same time, the pore size gradient is controlled from 0 up to 840%/μm yielding extreme asymmetry. In addition to structural analysis, water flux rates of over 5600 L m(-2) h(-1) are measured for membranes retaining 45 nm silica beads.

Physical Defect Formation in Few Layer Graphene-like Carbon on Metals: Influence of Temperature, Acidity, and Chemical Functionalization

A systematical examination of the chemical stability of cobalt metal nanomagnets with a graphene-like carbon coating is used to study the otherwise rather elusive formation of nanometer-sized physical defects in few layer graphene as a result of acid treatments. We therefore first exposed the core-shell nanomaterial to well-controlled solutions of altering acidity and temperature. The release of cobalt into these solutions over time offered a simple tool to monitor the progress of particle degradation. The results suggested that the oxidative damage of the graphene-like coatings was the rate-limiting step during particle degradation since only fully intact or entirely emptied carbon shells were found after the experiments. If ionic noble metal species were additionally present in the acidic solutions, the noble metal was found to reduce on the surface of specific, defective particles. The altered electrochemical gradients across the carbon shells were however not found to lead to a faster release of cobalt from the particles. The suggested mechanistic insight was further confirmed by the covalent chemical functionalization of the particle surface with chemically inert aryl species, which leads to an additional thickening of the shells. This leads to reduced cobalt release rates as well as slower noble metal reduction rates depending on the augmentation of the shell thickness.

Electrical resistivity of assembled transparent inorganic oxide nanoparticle thin layers: influence of silica, insulating impurities, and surfactant layer thickness.

The electrical properties of transparent, conductive layers prepared from nanoparticle dispersions of doped oxides are highly sensitive to impurities. Production of cost-effective thin conducting films for consumer electronics often employs wet processing such as spin and/or dip coating of surfactant-stabilized nanoparticle dispersions. This inherently results in entrainment of organic and inorganic impurities into the conducting layer leading to largely varying electrical conductivity. Therefore, this study provides a systematic investigation on the effect of insulating surfactants, small organic molecules and silica in terms of pressure dependent electrical resistivity as a result of different core/shell structures (layer thickness). Application of high temperature flame synthesis gives access to antimony-doped tin oxide (ATO) nanoparticles with high purity. This well-defined starting material was then subjected to representative film preparation processes using organic additives. In addition ATO nanoparticles were prepared with a homogeneous inorganic silica layer (silica layer thickness from 0.7 to 2 nm). Testing both organic and inorganic shell materials for the electronic transport through the nanoparticle composite allowed a systematic study on the influence of surface adsorbates (e.g., organic, insulating materials on the conducting nanoparticles surface) in comparison to well-known insulators such as silica. Insulating impurities or shells revealed a dominant influence of a tunneling effect on the overall layer resistance. Mechanical relaxation phenomena were found for 2 nm insulating shells for both large polymer surfactants and (inorganic) SiO(2) shells.

Limestone nanoparticles as nanopore templates in polymer membranes: narrow pore size distribution and use as self-wetting dialysis membranes

Limestone nanoparticles can be used as nanopore templates to prepare porous polymeric films. Their application as membranes is so far strongly limited by the fact that these films are highly hydrophobic. In this study, a simple method is reported to directly produce self-wetting membranes by the template removal method. Triethyl citrate modified polyethersulfone and cellulose acetate membranes were produced using dissolvable limestone nanoparticles as pore templates. The nanoporous polymer films were used as dialysis membranes and characterized by means of buffer exchange rate, molecular weight cut-off, protein adsorption, pore size distribution and water contact angle. The herein prepared membranes were further benchmarked against commercially available dialysis membranes with comparable average pore size. They showed narrow pore size distributions, fast dialysis rates at low protein adsorption and molecular weight cut-off of around 12 kDa. Interestingly, the triethyl citrate modified polyethersulfone membranes displayed only moderate change in pore size distribution as a result of the plasticizer additive compared to pure polyethersulfone membranes. This is a matter of substantial interest considering the fact that additive modifications of membranes produced by the predominant phase inversion process typically show alterations in morphology that lead to undesired changes in membrane performance. Furthermore, dextran recovery analysis proved to meet the specific requirements for dialysis membrane characterization and benchmarking.