Christopher A. Crouse

Synthesis, characterization, and carbon dioxide adsorption of covalently attached polyethyleneimine-functionalized single-wall carbon nanotubes.

The reaction between fluorinated single-wall carbon nanotubes (F-SWNTs) and branched (M(w) = 600, 1800, 10000, and 25000 Da) or linear (M(w) = 25000 Da) polyethyleneimine (PEI) yields the covalent attachment of the polymer to the sidewalls of the nanotubes. The resulting PEI-functionalized SWNTs (PEI-SWNTs) were characterized by solid-state (13)C NMR, Raman spectroscopy, X-ray photoelectron spectroscopy, UV-vis spectroscopy, atomic force microscopy, transmission electron microscopy, and thermal gravimetric analysis studies. As expected, the number of polymer molecules per SWNT is larger for low molecular weight PEI than for high molecular weight PEI. However, above 1800 Da, the number of polymer molecules per SWNT does not vary as much. This is supported by Raman spectral data that shows the D:G ratio is relatively insensitive of the molecular weight for M(w) > 1800 Da. The PEI-SWNTs are shown to have solubility in aqueous media of up to 0.4 mg x mL(-1). Solid-state (13)C NMR shows the presence of carboxylate substituents that have been attributed to carbamate formation as a consequence of the reversable CO(2) absorption to the primary amine substituents of the PEI. Desorption of CO(2) is accomplished by heating under argon at 75 degrees C, while the dependence of the quantity of CO(2) absorbed on temperature and the molecular weight of the PEI is reported. Under the conditions investigated the maximum absorption of 9.2% w/w is observed for PEI(25000)-SWNT at 27 degrees C. The possible CO(2) absorption applications of the PEI-SWNTs is discussed.

Growth, new growth, and amplification of carbon nanotubes as a function of catalyst composition.

Carbon nanotubes (CNTs) have been grown using Fe, Co, Ni, and Co/Fe spin-on-catalyst (SOC) systems, involving the metal salt dispersed with a spin-on-glass precursor. During initial growth runs (CH4/H2/900 degrees C), the CNT yield followed the order Co-SOC > Fe-SOC >> Ni-SOC. The Fe catalysts produced the longest nanotubes at the expense of a larger average CNT diameter and broader diameter distribution than the Co-SOC system. A series of Co/Fe-SOCs were prepared where as the atomic percentage of Co is increased nucleation of CNT increases but the CNT length decreases. The linear relationship between the diameter and length of CNTs grown from the Co/Fe-SOC suggests that slow growth is beneficial with respect to control over CNT diameter. After initial CNT growth, the original samples were subjected to additional growth runs. Four individual reactions were observed in the Fe-SOC and binary Co/Fe-SOC: regrowth (amplification), double growth (a second CNT growing from a previously active catalyst), CNT etching, and nucleation from initially inactive catalysts (new growth). CNT etching was observed for the mixed catalyst systems (Co/Fe-SOC) but not for either Fe-SOC or Co-SOC. During the regrowth experiments, CNTs were observed that were not present after the initial growth run (and were not as a result of amplification or double growth). Thus, catalysts, which were initially inactive toward nucleation of CNTs in the original growth run, are capable of becoming activated when placed back into the furnace and submitted to regrowth under identical conditions.

Biologically Tunable Reactivity of Energetic Nanomaterials Using Protein Cages

The performance of aluminum nanomaterial based energetic formulations is dependent on the mass transport, diffusion distance, and stability of reactive components. Here we use a biologically inspired approach to direct the assembly of oxidizer loaded protein cages onto the surface of aluminum nanoparticles to improve reaction kinetics by reducing the diffusion distance between the reactants. Ferritin protein cages were loaded with ammonium perchlorate (AP) or iron oxide and assembled with nAl to create an oxidation-reduction based energetic reaction and the first demonstration of a nanoscale biobased thermite material. Both materials showed enhanced exothermic behavior in comparison to nanothermite mixtures of bulk free AP or synthesized iron oxide nanopowders prepared without the use of ferritin. In addition, by utilizing a layer-by-layer (LbL) process to build multiple layers of protein cages containing iron oxide and iron oxide/AP on nAl, stoichiometric conditions and energetic performance can be optimized.

A study of the formation, purification and application as a SWNT growth catalyst of the nanocluster [HxPMo12O40⊂H4Mo72Fe30(O2CMe)15O254(H2O)98]

The synthetic conditions for the isolation of the iron-molybdenum nanocluster FeMoC [HxPMo12O40 [subset]H4Mo72Fe30(O2CMe)15O254(H2O)98], along with its application as a catalyst precursor for VLS growth of SWNTs have been studied. As-prepared FeMoC is contaminated with the Keplerate cage [H4Mo72Fe30(O2CMe)15O254(H2O)98] without the Keggin [HxPMo12O40]n- template, however, isolation of pure FeMoC may be accomplished by Soxhlet extraction with EtOH. The resulting EtOH solvate is consistent with the replacement of the water ligands coordinated to Fe being substituted by EtOH. FeMoC-EtOH has been characterized by IR, UV-vis spectroscopy, MS, XPS and 31P NMR. The solid-state 31P NMR spectrum for FeMoC-EtOH (delta-5.3 ppm) suggests little effect of the paramagnetic Fe3+ centers in the Keplerate cage on the Keggin ions phosphorous. The high chemical shift anisotropy, and calculated T1 (35 ms) and T2 (8 ms) values are consistent with a weak magnetic interaction between the Keggin ions phosphorus symmetrically located within the Keplerate cage. Increasing the FeCl2 concentration and decreasing the pH of the reaction mixture optimizes the yield of FeMoC. The solubility and stability of FeMoC in H2O and MeOH-H2O is investigated. The TGA of FeMoC-EtOH under air, Ar and H2 (in combination with XPS) shows that upon thermolysis the resulting Fe : Mo ratio is highly dependent on the reaction atmosphere: thermolysis in air results in significant loss of volatile molybdenum components. Pure FeMoC-EtOH is found to be essentially inactive as a pre-catalyst for the VLS growth of single-walled carbon nanotubes (SWNTs) irrespective of the substrate or reaction conditions. However, reaction of FeMoC with pyrazine (pyz) results in the formation of aggregates that are found to be active catalysts for the growth of SWNTs. Activation of FeMoC may also be accomplished by the addition of excess iron. The observation of prior works reported growth of SWNTs from FeMoC is discussed with respect to these results.

Self-Assembled Monolayer and Multilayer Films of the Nanocluster [HxPMo12O40⊂H4Mo72Fe30(O2CMe)15O254(H2O)68] on Gold

Films of the molybdenum-iron nanocluster [H x PMo 12O 40 subsetH 4Mo 72Fe 30(O 2CMe) 15O 254(H2O) 68] (FeMoC) were generated on gold via the self-assembly technique using two divergent routes. The first route entails the self-assembly of unfunctionalized FeMoC onto a preprepared carboxyl-terminated SAM on gold. The second route involves the preparation of thiol-terminated functionalized FeMoC clusters, which are then allowed to self-assemble onto bare gold surfaces. Monolayer films of FeMoC clusters are attained via both routes, with the second route requiring shorter immersion times (2 days) than the first route (6 days). Multilayer films of FeMoC are formed via the second route for immersion times longer than 2 days. Characterization of these films using optical ellipsometry, X-ray photoelectron spectroscopy, and atomic force microscopy confirm the self-assembly of the clusters on the surfaces.

Impact Initiation of Reactive Aluminized Fluorinated Acrylic Nanocomposites

The initiation of aluminized fluorinated acrylic (AlFA) nanocomposites during modified Taylor impact tests was investigated. Samples were impacted against a steel or sapphire anvil at a nominal velocity of 150 m/s. A framing camera was used to capture head-on and side-profile impact images for the sapphire window and steel plate rigid anvils, respectively. Correlations were drawn between both experimental setups to determine the initiation locations and reaction times. Reactions were found to initiate at an intermediate radius on the impact face of the pellet at a time near full compaction. From simulations, the highest strains and temperatures were found at radii similar to those observed in experiments at the time of ignition. Off-normal impacts produced higher localized straining and temperatures on one-half of the pellet. The copper projectile, used for delivery, was revealed to aid in a shear assisted reaction by helping to drive the pellet material outward as the projectile deformed radially.