Clémence Coetsier

Mineralization of organic pollutants by anodic oxidation using reactive electrochemical membrane synthesized from carbothermal reduction of TiO2

Reactive Electrochemical Membrane (REM) prepared from carbothermal reduction of TiO2 is used for the mineralization of biorefractory pollutants during filtration operation. The mixture of Ti4O7 and Ti5O9 Magnéli phases ensures the high reactivity of the membrane for organic compound oxidation through •OH mediated oxidation and direct electron transfer. In cross-flow filtration mode, convection-enhanced mass transport of pollutants can be achieved from the high membrane permeability (3300 LMH bar-1). Mineralization efficiency of oxalic acid, paracetamol and phenol was assessed as regards to current density, transmembrane pressure and feed concentration. Unprecedented high removal rates of total organic carbon and mineralization current efficiency were achieved after a single passage through the REM, e.g. 47 g m-2 h-1 - 72% and 6.7 g m-2 h-1 - 47% for oxalic acid and paracetamol, respectively, at 15 mA cm-2. However, two mechanisms have to be considered for optimization of the process. When the TOC flux is too high with respect to the current density, aromatic compounds polymerize in the REM layer where only direct electron transfer occurs. This phenomenon decreases the oxidation efficiency and/or increases REM fouling. Besides, O2 bubbles sweeping at high permeate flux promotes O2 gas generation, with adverse effect on oxidation efficiency.

Feasibility of Micropollutants Treatment by Coupling Nanofiltration and Electrochemical Oxidation: Case of Hospital Wastewater

Abstract In spite of good performances of the membrane bioreactor (MBR) process, permeate from it can still contain refractory pollutants that have to be removed before water reuse or discharge. The present study is an attempt to combine the advantages of two well-known technologies, which are nanofiltration (NF) and electrochemical oxidation (EO) to treat MBR effluent from hospital wastewater. The concept is based on a preconcentration of micropollutants with a reduction of the wastewater volume by NF and treatment of the NF retentate by oxidation. During filtration process the rejection of ciprofloxacin, as a target molecule, reached beyond 97%. Then the NF retentate was treated by EO using a boron-doped diamond anode (BDD). Galvanostatic electrolyses showed that this anode is efficient to mineralize not only ciprofloxacin but also all the micropollutants and organics contained in MBR effluent. The results demonstrated that rapid mineralization occurred: the removal of total organic carbon and chemical oxygen demand (COD) reached 97% and 100%, respectively, in our conditions in 300 min maximum. The specific energy consumption for the total removal of COD was calculated to be 50 kW h kg˗1 COD.

Nanofiltration performances after membrane bioreactor for hospital wastewater treatment: Fouling mechanisms and the quantitative link between stable fluxes and the water matrix

Treatment combining membrane bioreactors (MBR) and nanofiltration (NF) is becoming an emerging wastewater treatment strategy. The combined process is capable of producing high quality water potentially reusable; however, diverse compositions of MBR effluents induce several types and degrees of NF membrane fouling that impacts process productivity. Moreover, since MBR effluent composition for one type of wastewater source is variable depending on the MBR efficiency at different periods, downstream NF membrane fouling types and degrees may consequently change over time. In that context, the present paper aims at developing effective fouling control strategies of NF membrane in the case of the filtration of MBR effluents taken from a MBR system installed in a French hospital. These effluents were filtrated under various transmembrane pressures, and stable fluxes during these filtrations were determined. Several types and degrees of fouling mechanisms were then identified through surface morphology observation and the analysis of chemical compositions of fouled membranes. The diverse flux behaviour was further associated with the fouling mechanisms and foulant compositions. Based on the study of these mechanisms, the quantitative link between stable fluxes and calcium phosphate concentrations in MBR effluents has been established.

Electro-oxidation of organic pollutants by reactive electrochemical membranes

Electro-oxidation processes are promising options for the removal of organic pollutants from water. The major appeal of these technologies is the possibility to avoid the addition of chemical reagents. However, a major limitation is associated with slow mass transfer that reduces the efficiency and hinders the potential for large-scale application of these technologies. Therefore, improving the reactor configuration is currently one of the most important areas for research and development. The recent development of a reactive electrochemical membrane (REM) as a flow-through electrode has proven to be a breakthrough innovation, leading to both high electrochemically active surface area and convection-enhanced mass transport of pollutants. This review summarizes the current state of the art on REMs for the electro-oxidation of organic compounds by anodic oxidation. Specific focuses on the electroactive surface area, mass transport, reactivity, fouling and stability of REMs are included. Recent advances in the development of sub-stoichiometric titanium oxide REMs as anodes have been made. These electrodes possess high electrical conductivity, reactivity (generation of •OH), chemical/electrochemical stability, and suitable pore structure that allows for efficient mass transport. Further development of REMs strongly relies on the development of materials with suitable physico-chemical characteristics that produce electrodes with efficient mass transport properties, high electroactive surface area, high reactivity and long-term stability.