Cormac Fay

A wearable electrochemical sensor for the real-time measurement of sweat sodium concentration

We report a new method for the real-time quantitative analysis of sodium in human sweat, consolidating sweat collection and analysis in a single, integrated, wearable platform. This temporal data opens up new possibilities in the study of human physiology, broadly applicable from assessing high performance athletes to monitoring Cystic Fibrosis (CF) sufferers. Our compact Sodium Sensor Belt (SSB) consists of a sodium selective Ion Selective Electrode (ISE) integrated into a platform that can be interfaced with the human body during exercise. No skin cleaning regime or sweat storage technology is required as the sweat is continually wicked from the skin to a sensing surface and from there to a storage area via a fabric pump. Our results suggest that after an initial equilibration period, a steady-state sodium plateau concentration was reached. Atomic Absorption Spectroscopy (AAS) was used as a reference method, and this has confirmed the accuracy of the new continuous monitoring approach. The steady-state concentrations observed were found to fall within ranges previously found in the literature, which further validates the approach. Daily calibration repeatability (n = 4) was ±3.0% RSD and over a three month period reproducibility was ±12.1% RSD (n = 56). As a further application, we attempted to monitor the sweat of Cystic Fibrosis (CF) sufferers using the same device. We observed high sodium concentrations symptomatic of CF (∼60 mM Na+) for two CF patients, with no conclusive results for the remaining patients due to their limited exercising capability, and high viscosity/low volume of sweat produced.

A new light emitting diode-light emitting diode portable carbon dioxide gas sensor based on an interchangeable membrane system for industrial applications.

A new system for CO(2) measurement (0-100%) based on a paired emitter-detector diode arrangement as a colorimetric detection system is described. Two different configurations were tested: configuration 1 (an opposite side configuration) where a secondary inner-filter effect accounts for CO(2) sensitivity. This configuration involves the absorption of the phosphorescence emitted from a CO(2)-insensitive luminophore by an acid-base indicator and configuration 2 wherein the membrane containing the luminophore is removed, simplifying the sensing membrane that now only contains the acid-base indicator. In addition, two different instrumental configurations have been studied, using a paired emitter-detector diode system, consisting of two LEDs wherein one is used as the light source (emitter) and the other is used in reverse bias mode as the light detector. The first configuration uses a green LED as emitter and a red LED as detector, whereas in the second case two identical red LEDs are used as emitter and detector. The system was characterised in terms of sensitivity, dynamic response, reproducibility, stability and temperature influence. We found that configuration 2 presented a better CO(2) response in terms of sensitivity.

An integrated sensing and wireless communications platform for sensing sodium in sweat

The ability to non-invasively monitor sodium levels in sweat is of significant importance. Sodium is one of the preferred markers to diagnose and track the progression of cystic fibrosis, and knowledge of sodium levels could potentially enable personalised hydration strategies to be implemented for athletes or people working under severe environmental conditions. Herein we present a novel approach for the realisation of disposable potentiometric strips that allow for real-time monitoring of sodium in sweat. Our platform consists of a Solid-Contact Ion-Selective Electrode (SC-ISE) for Na+ detection and of a liquid-junction-free Reference Electrode (RE), combined together on a dual screen-printed substrate. Different poly-3,4-ethylenedioxythiophene (PEDOT) based films were tested as solid-contact, showing a significant impact on sensor characteristics such as sensitivity (i.e. differing from sub-Nernstian to Nernstian), dynamic range (i.e. 10−5 to 10−2.5 or 10−5 to 10−1aNa+), and especially within-batch reproducibility. The SC-ISE/RE combination was integrated into a microfluidic chip that was tested and optimised via on-bench trials. The Potentiometric Microfluidic Chip (PotMicroChip) was then connected to a wireless electronic platform to realise a wearable device whose performance was assessed during real-time stationary cycling sessions.

Portable integrated microfluidic analytical platform for the monitoring and detection of nitrite.

A wireless, portable, fully-integrated microfluidic analytical platform has been developed and applied to the monitoring and determination of nitrite anions in water, using the Griess method. The colour intensity of the Griess reagent nitrite complex is detected using a low cost Paired Emitter Detector Diode, while on-chip fluid manipulation is performed using a biomimetic photoresponsive ionogel microvalve, controlled by a white light LED. The microfluidic analytical platform exhibited very low limits of detection (34.0±0.1 μg L(-1) of NO2(-)). Results obtained with split freshwater samples showed good agreement between the microfluidic chip platform and a conventional UV-vis spectrophotometer (R(2)=0.98, RSD=1.93% and R(2)=0.99, RSD=1.57%, respectively). The small size, low weight, and low cost of the proposed microfluidic platform coupled with integrated wireless communications capabilities make it ideal for in situ environmental monitoring. The prototype device allows instrument operational parameters to be controlled and analytical data to be downloaded from remote locations. To our knowledge, this is the first demonstration of a fully functional microfluidic platform with integrated photo-based valving and photo-detection.

Autonomous greenhouse gas measurement system for analysis of gas migration on landfill sites

This paper describes the design, development and validation of an autonomous gas sensing platform prototype for monitoring of the greenhouse gases, methane (CH4) and carbon dioxide (CO2). The deployment undertaken for validation of the developed prototype monitored landfill gas migration to perimeter borehole wells on a landfill site. Target gas concentrations were captured via infrared gas sensors tuned for each target gas and data reported to an offsite data collection point at 12 hour intervals. This bespoke platform and the accompanying data recording and interface software provide a flexible alternative to the presently employed labor intensive, manual monitoring routines. This successful trial brought about a change in the management of the trial sites gas extraction system.

Wireless Ion-Selective Electrode Autonomous Sensing System

A paradigm shift in sensing methods and principles is required to meet the legislative demands for detecting hazardous substances in the molecular world. This will encompass the development of new sensing technologies capable of performing very selective and sensitive measurements at an acceptable cost, developed by multidisciplinary teams of chemists, engineers and computer scientists to harvest information from a multitude of molecular targets in health, food and within the environment. In this study we present the successful implementation of a low-cost, wireless chemical sensing system that employs a minimum set of components for effective operation. Specifically, our efforts resulted in a wireless, tri-electrode, ISE pH sensor for use in environmental monitoring. Sensor calibration and validated in situ field trials have been carried out and are presented in this paper.

Wearable technology for bio-chemical analysis of body fluids during exercise

This paper details the development of a textile based fluid handling system with integrated wireless biochemical sensors. Such research represents a new advancement in the area of wearable technologies. The system contains pH, sodium and conductivity sensors. It has been demonstrated during on-body trials that the pH sensor has close agreement with measurements obtained using a reference pH probe. Initial investigations into the sodium and conductivity sensors have shown their suitability for integration into the wearable system. It is thought that applications exist in personal health and sports performance and training.

Remote Real-Time Monitoring of Subsurface Landfill Gas Migration

The cost of monitoring greenhouse gas emissions from landfill sites is of major concern for regulatory authorities. The current monitoring procedure is recognised as labour intensive, requiring agency inspectors to physically travel to perimeter borehole wells in rough terrain and manually measure gas concentration levels with expensive hand-held instrumentation. In this article we present a cost-effective and efficient system for remotely monitoring landfill subsurface migration of methane and carbon dioxide concentration levels. Based purely on an autonomous sensing architecture, the proposed sensing platform was capable of performing complex analytical measurements in situ and successfully communicating the data remotely to a cloud database. A web tool was developed to present the sensed data to relevant stakeholders. We report our experiences in deploying such an approach in the field over a period of approximately 16 months.

Wearable sensors for monitoring sports performance and training

Textile based devices for biochemical analysis of body fluids represent a new development in the area of wearable sensors. This paper outlines the development of a fluid handling system and wireless sensors for the real-time analysis of sweat pH and sodium levels during exercise. Liquid is drawn into the system using a moisture wicking material and passive pump. The sensor then displays pH induced colorimetric changes, which are recorded using an optical detection system. The device has been tested under laboratory conditions and can easily detect increments of 0.2 pH units. At present, changes in sodium content are determined using a specially constructed classic ion selective electrode and reference electrode, combined to form a single probe. This is placed in contact with the fabric of the fluid handling system in order to obtain a real-time potentiometric sodium measurement. Both devices have successfully been used for the investigation of sweat composition during on-body trials.

A Wearable Device for Monitoring Sweat Rates via Image Analysis

A feasibility study on a new technique capable of monitoring localized sweat rate is explored in this paper. Wearable devices commonly used in clinical practice for sweat sampling (i.e., Macroducts) were positioned on the body of an athlete whose sweat rate was then monitored during cycling sessions. The position at which the sweat fills the Macroduct was indicated by a contrasting marker and captured via a series of time-stamped photos or a video recording of the device during an exercise period. Given that the time of each captured image/frame is known (either through time stamp on photos or the constant frame rate of the video capture), it was, therefore, possible to estimate the sweat flow rate through a simple calibration model. The importance of gathering such valuable information is described, together with the results from a number of exercise trials to investigate the viability of this approach.