D.C. Papa

A wideband fixed-tuned SIS receiver for 200-GHz operation

We report on the design and development of a heterodyne receiver, designed to cover the frequency range 176-256 GHz. This receiver incorporates a niobium superconductor-insulator-superconductor (SIS) tunnel junction mixer, which, chiefly for reasons of reliability and ease of operation, is a fixed-tuned waveguide design. On-chip tuning is provided to resonate out the junctions geometric capacitance and produce a good match to the waveguide circuit. Laboratory measurements on the first test receiver indicate that the required input bandwidth (about 40%) is achieved with an average receiver noise temperature of below 50 K. Mixer conversion gain is observed at some frequencies, and the lowest measured receiver noise is less than 30 K. Furthermore, the SIS mixer used in this receiver is of simple construction, is easy to assemble and is therefore a good candidate for duplication. >

Design and characterization of a 250-350-GHz fixed-tuned superconductor-insulator-superconductor receiver

A fixed-tuned superconductor-insulator-superconductor (SIS) receiver has been designed to operate in the 250-350-GHz frequency band. This receiver has a double-side-band noise temperature of between 35 and 45 K, or about 3h/spl nu//k/sub B/, over its entire operating band. Extensive characterization of the receiver has been carried out using techniques developed for submillimeter waves. The input noise, side-band ratio, 1 dB compression point, optimum LO drive level, and vector near-field beam profile have all been measured experimentally. The measurement techniques and results are presented and discussed.

A 1-THz superconducting hot-electron-bolometer receiver for astronomical observations

In this paper, we describe a superconducting hot-electron-bolometer mixer receiver developed to operate in atmospheric windows between 800-1300 GHz. The receiver uses a waveguide mixer element made of 3-4-nm-thick NbN film deposited over crystalline quartz. This mixer yields double-sideband receiver noise temperatures of 1000 K at around 1.0 THz, and 1600 K at 1.26 THz, at an IF of 3.0 GHz. The receiver was successfully tested in the laboratory using a gas cell as a spectral line test source. It is now in use on the Smithsonian Astrophysical Observatory terahertz test telescope in northern Chile.

Superconductive hot-electron-bolometer mixer receiver for 800-GHz operation

In this paper, we describe a superconductive hot-electron-bolometer mixer receiver designed to operate in the partially transmissive 350-/spl mu/m atmospheric window. The receiver employs an NbN thin-film microbridge as the mixer element, in which the main cooling mechanism of the hot electrons is through electron-phonon interaction. At a local-oscillator frequency of 808 GHz, the measured double-sideband receiver noise temperature is T/sub RX/=970 K, across a 1-GHz intermediate-frequency bandwidth centered at 1.8 GHz. We have measured the linearity of the receiver and the amount of local-oscillator power incident on the mixer for optimal operation, which is P/sub LO//spl ap/1 /spl mu/W. This receiver was used in making observations as a facility instrument at the Heinrich Hertz Telescope, Mt. Graham, AZ, during the 1998-1999 winter observing season.

Terahertz-frequency waveguide NbN hot-electron bolometer mixer

We have developed a low-noise waveguide heterodyne receiver for operation near 1 THz using phonon-cooled NbN hot-electron bolometers. The mixer elements are submicron-sized microbridges of 4 nm-thick NbN film fabricated on a quartz substrate. Operating at a bath temperature of 4.2 K, the double-sideband receiver noise temperature is 760 K at 1.02 THz and 1100 K at 1.26 THz. The local oscillator is provided by solid-state sources, and power measured at the source is less than 1 /spl mu/W. The intermediate frequency bandwidth exceeds 2 GHz. The receiver was used to make the first ground-based heterodyne detection of a celestial spectroscopic line above 1 THz.

An all solid-state superconducting heterodyne receiver at terahertz frequencies

A superconducting hot-electron bolometer mixer-receiver operating from 1 to 1.26 THz has been developed. This heterodyne receiver employs two solid-state local oscillators each consisting of a Gunn oscillator followed by two stages of varactor frequency multiplication. The measured receiver noise temperature is 1350 K at 1.035 THz and 2700 K at 1.26 THz. This receiver demonstrates that tunable solid-state local oscillators, supplying only a few micro-watts of output power, can be used in terahertz receiver applications.

A near-field alignment technique at millimeter and sub-millimeter wavelengths

We have employed a portable near-field scanner operating at millimeter and sub-millimeter wavelengths to map the 2D amplitude and phase patterns of a radio beam. Combined with a numerical transform, we have developed a novel alignment procedure to diagnose the alignment error in a complex receiving system. The optics of a multiband, superconducting receiver have been aligned using this technique.