D.L. Rudakov

Transport by intermittency in the boundary of the DIII-D tokamak

A271 TRANSPORT BY INTERMITTENCY IN THE BOUNDARY OF THE DIII-D TOKAMAK. Intermittent plasma objectives (IPOs) featuring higher pressure than the surrounding plasma, are responsible for {approx} 50% of the E x B{sub T} radial transport in the scrape off layer (SOL) of the DIII-D tokamak in L- and H-mode discharges. Conditional averaging reveals that the IPOs are positively charged and feature internal poloidal electric fields of up to 4000 V/m. The IPOs move radially with E x B{sub T}/B{sup 2} velocities of {approx} 2600 m/s near the last closed flux surface (LCFS), and {approx} 330 m/s near the wall. The IPOs slow down as they shrink in radial size from 4 cm at the LCFS to 0.5 cm near the wall. The skewness (i.e. asymmetry of fluctuations from the average) of probe and beam emission spectroscopy (BES) data indicate IPO formation at or near the LCFS and the existence of positive and negative IPOs which move in opposite directions. The particle content of the IPOs at the LCFS is linearly dependent on the local density and decays over {approx} 3 cm into the SOL while their temperature decays much faster ({approx} 1 cm).

Dust measurements in tokamaks (invited)

Dust production and accumulation present potential safety and operational issues for the ITER. Dust diagnostics can be divided into two groups: diagnostics of dust on surfaces and diagnostics of dust in plasma. Diagnostics from both groups are employed in contemporary tokamaks; new diagnostics suitable for ITER are also being developed and tested. Dust accumulation in ITER is likely to occur in hidden areas, e.g., between tiles and under divertor baffles. A novel electrostatic dust detector for monitoring dust in these regions has been developed and tested at PPPL. In the DIII-D tokamak dust diagnostics include Mie scattering from Nd:YAG lasers, visible imaging, and spectroscopy. Laser scattering is able to resolve particles between 0.16 and 1.6 microm in diameter; using these data the total dust content in the edge plasmas and trends in the dust production rates within this size range have been established. Individual dust particles are observed by visible imaging using fast framing cameras, detecting dust particles of a few microns in diameter and larger. Dust velocities and trajectories can be determined in two-dimension with a single camera or three-dimension using multiple cameras, but determination of particle size is challenging. In order to calibrate diagnostics and benchmark dust dynamics modeling, precharacterized carbon dust has been injected into the lower divertor of DIII-D. Injected dust is seen by cameras, and spectroscopic diagnostics observe an increase in carbon line (CI, CII, C(2) dimer) and thermal continuum emissions from the injected dust. The latter observation can be used in the design of novel dust survey diagnostics.

Dust in magnetic fusion devices

This paper reviews recent results of the study of dust in magnetic fusion devices. Assessment of the role of dust in current fusion devices and ITER is presented. Dust diagnostics, main experimental results, different theoretical aspects of dust in fusion plasmas, as well as the comparison of theoretical estimates and numerical simulations with available experimental data are discussed. Some limitations of current theoretical models of dust–plasma interactions and the gaps in current experimental and theoretical approaches to dust study in fusion devices are considered. Possible directions for further advancements are suggested.

Experimental characterization of coherent, radially-sheared zonal flows in the DIII-D tokamak

A271 EXPERIMENTAL CHARACTERIZATION OF COHERENT, RADIALLY-SHEARED ZONAL FLOWS IN THE DIII-D TOKAMAK. Application of time-delay-estimation techniques to two-dimensional measurements of density fluctuations, obtained with beam emission spectroscopy in DIII-D plasmas, has provided temporally and spatially resolved measurements of the turbulence flow-field. Features that are characteristic of self-generated zonal flows are observed in the radial region near 0.85 {<=} r/a {<=} 1.0. These features include a coherent oscillation (approximately 15 kHz) in the poloidal flow of density fluctuations that has a long poloidal wavelength, possibly m = 0, narrow radial extent (k{sub r}{rho}{sub I} < 0.2), and whose frequency varies monotonically with the local temperature. The approximate effective shearing rate, dv{sub {theta}}/dr, of the flow is of the same order of magnitude as the measured nonlinear decorrelation rate of the turbulence, and the density fluctuation amplitude is modulated at the frequency of the observed flow oscillation. Some phase coherence is observed between the higher wavenumber density fluctuations and low frequency poloidal flow fluctuations, suggesting a Reynolds stress contribution. These characteristics are consistent with predicted features of zonal flows, specifically identified as geodesic acoustic modes, observed in 3-D Braginskii simulations of core/edge turbulence.

Fluctuation-driven transport in the DIII-D boundary

Cross-field fluctuation-driven transport is studied in edge and scrape-off layer (SOL) plasmas in the DIII-D tokamak using a fast reciprocating Langmuir probe array allowing local measurements of the fluctuation-driven particle and heat fluxes. Two different non-diffusive mechanisms that can contribute strongly to the cross-field transport in the SOL of high-density discharges are identified and compared. The first of these involves intermittent transport events that are observed at the plasma separatrix and in the SOL. Intermittence has qualitatively similar character in L-mode and ELM-free H-mode. Low-amplitude ELMs observed in high-density H-mode produce in the SOL periods with cross-field transport enhanced to L-mode levels and featuring intermittent events similar to those in L-mode. The intermittent transport events are compatible with the concept of plasma filaments propagating across the SOL due to E×B drifts. The intermittent character of the transport in the SOL is also in agreement with predictions of the non-linear numerical simulations performed with an imposed driving flux. Another type of non-diffusive transport is often seen in high-density H-modes with prolonged ELM-free periods, where the transport near the separatrix is dominated by quasi-coherent modes driving particle and/or heat fluxes exceeding L-mode levels. These modes may play an important role by providing particle and/or heat exhaust between ELMs.

First tests of molybdenum mirrors for ITER diagnostics in DIII-D divertor

Metallic mirrors will be used in ITER for optical diagnostics working in different spectral ranges. Their optical properties will change with time due to erosion, deposition, and particle implantation. First tests of molybdenum mirrors were performed in the DIII-D divertor under deposition-dominated conditions. Two sets of mirrors recessed 2cm below the divertor floor in the private flux region were exposed to a series of identical, lower-single-null, ELMing (featuring edge localized modes) H-mode discharges with detached plasma conditions in both divertor legs. The first set of mirrors was exposed at ambient temperature, while the second set was preheated to temperatures between 140 and 80°C. During the exposures mirrors in both sets were additionally heated by radiation from the plasma. The nonheated mirrors exhibited net carbon deposition at a rate of up to 3.7nm∕s and suffered a significant drop in reflectivity. Net carbon deposition rate on the preheated mirrors was a factor of 30–100 lower and their...

Plasma?surface interaction, scrape-off layer and divertor physics: implications for ITER

Recent research in scrape-off layer (SOL) and divertor physics is reviewed; new and existing data from a variety of experiments have been used to make cross-experiment comparisons with implications for further research and ITER. Studies of the region near the separatrix have addressed the relationship of profiles to turbulence as well as the scaling of the parallel power flow. Enhanced low-field side radial transport is implicated as driving parallel flows to the inboard side. The medium-n nature of edge localized modes (ELMs) has been elucidated and new measurements have determined that they carry ~10?20% of the ELM energy to the far SOL with implications for ITER limiters and the upper divertor. The predicted divertor power loads for ITER disruptions are reduced while those to main chamber plasma facing components (PFCs) increase. Disruption mitigation through massive gas puffing is successful at reducing PFC heat loads. New estimates of ITER tritium retention have shown tile sides to play a significant role; tritium cleanup may be necessary every few days to weeks. ITERs use of mixed materials gives rise to a reduction of surface melting temperatures and chemical sputtering. Advances in modelling of the ITER divertor and flows have enhanced the capability to match experimental data and predict ITER performance.

Suppression of large edge localized modes with edge resonant magnetic fields in high confinement DIII-D plasmas

Large sub-millisecond heat pulses due to Type-I edge localized modes (ELMs) have been eliminated reproducibly in DIII-D for periods approaching nine energy confinement times (τE) with small dc currents driven in a simple magnetic perturbation coil. The current required to eliminate all but a few isolated Type-I ELM impulses during a coil pulse is less than 0.4% of plasma current. Based on magnetic field line modelling, the perturbation fields resonate with plasma flux surfaces across most of the pedestal region (0.9 ≤ ψN ≤ 1.0) when q95 = 3.7 ± 0.2, creating small remnant magnetic islands surrounded by weakly stochastic field lines. The stored energy, βN, H-mode quality factor and global energy confinement time are unaltered by the magnetic perturbation. Although some isolated ELMs occur during the coil pulse, long periods free of large Type-I ELMs (Δt > 4–6 τE) have been reproduced numerous times, on multiple experimental run days in high and intermediate triangularity plasmas, including cases matching the baseline ITER scenario 2 flux surface shape. In low triangularity, lower single null plasmas, with collisionalities near that expected in ITER, Type-I ELMs are replaced by small amplitude, high frequency Type-II-like ELMs and are often accompanied by one or more ELM-free periods approaching 1–2 τE. Large Type-I ELM impulses represent a severe constraint on the survivability of the divertor target plates in future burning plasma devices. Results presented in this paper demonstrate that non-axisymmetric edge magnetic perturbations provide a very attractive development path for active ELM control in future tokamaks such as ITER.

Edge Localized Mode Control with an Edge Resonant Magnetic Perturbation

This work was funded by the U.S. Department of Energy under Grant Nos. DE-FC02-04ER54698, DE-FG02- 04ER54758, DE-FG03-01ER54615, W-7405-ENG-48, DEFG03-96ER54373, DE-FG02-89ER53297, DE-AC05- 00OR22725, and DE-AC04-94AL85000.

Far SOL transport and main wall plasma interaction in DIII-D

Far Scrape-Off Layer (SOL) and near-wall plasma parameters in DIII-D depend strongly on the discharge parameters and confinement regime. In L-mode discharges cross-field transport increases with the average discharge density and flattens far SOL profiles, thus increasing plasma contact with the low field side (LFS) main chamber wall. In H-mode between edge localized modes (ELMs) the plasma?wall contact is weaker than in L-mode. During ELM fluxes of particles and heat to the LFS wall increase transiently above the L-mode values. Depending on the discharge conditions, ELMs are responsible for 30?90% of the net ion flux to the outboard chamber wall. ELMs in high density discharges feature intermittent transport events similar to those observed in L-mode and attributed to blobs of dense hot plasma formed inside the separatrix and propagating radially outwards. Though the blobs decay with radius, some of them survive long enough to reach the outer wall and possibly cause sputtering. In lower density H-modes, ELMs can feature blobs of pedestal density propagating all the way to the outer wall.