Daniel C. Bowden

Site amplification, attenuation, and scattering from noise correlation amplitudes across a dense array in Long Beach, CA

For accurate seismic hazard evaluation, both the spatial and frequency-dependent variabilities in the amplitudes of earthquake ground motions are needed. While this information is rarely fully available due to the paucity of relevant seismic data, dense arrays like the 5200-geophone array in Long Beach, California provide the opportunity to study this amplitude variability. Here we show that ambient noise correlation amplitudes from the Long Beach array can be used to directly determine frequency-dependent site amplification factors. We analyze Rayleigh-wavefield amplitude gradients from ambient noise correlations that are processed so that relative amplitudes satisfy the wave equation and are therefore meaningful. Ultimately, we construct maps of site amplification across Long Beach at frequencies of 0.67, 1.0, and 2.0 Hz. These maps correlate well with local structure, notably the Newport-Inglewood Fault and also to known velocity structure. Through this process, we also obtain constraints on average attenuation structure and local scattering.

Earthquake ground motion amplification for surface waves

Surface waves from earthquakes are known to cause strong damage, especially for larger structures such as skyscrapers and bridges. However, common practice in characterizing seismic hazard at a specific site considers the effect of near-surface geology on only vertically propagating body waves. Here we show that surface waves have a unique and different frequency-dependent response to known geologic structure and that this amplification can be analytically calculated in a manner similar to current hazard practices. Applying this framework to amplification in the Los Angeles Basin, we find that peak ground accelerations for certain large regional earthquakes are underpredicted if surface waves are not properly accounted for and that the frequency of strongest ground motion amplification can be significantly different. Including surface-wave amplification in hazards calculations is therefore essential for accurate predictions of strong ground motion for future San Andreas Fault ruptures.

Offshore Southern California lithospheric velocity structure from noise cross‐correlation functions

A new shear wave velocity model offshore Southern California is presented that images plate boundary deformation including both thickening and thinning of the crustal and mantle lithosphere at the westernmost edge of the North American continent. The Asthenospheric and Lithospheric Broadband Architecture from the California Offshore Region Experiment (ALBACORE) ocean bottom seismometer array, together with 65 stations of the onshore Southern California Seismic Network, is used to measure ambient noise correlation functions and Rayleigh wave dispersion curves which are inverted for 3-D shear wave velocities. The resulting velocity model defines the transition from continental lithosphere to oceanic, illuminating the complex history and deformation in the region. A transition to the present-day strike-slip regime between the Pacific and North American Plates resulted in broad deformation and capture of the now >200 km wide continental shelf. Our velocity model suggests the persistence of the uppermost mantle volcanic processes associated with East Pacific Rise spreading adjacent to the Patton Escarpment, which marks the former subduction of Farallon Plate underneath North America. The most prominent of these seismic structures is a low-velocity anomaly underlying the San Juan Seamount, suggesting ponding of magma at the base of the crust, resulting in thickening and ongoing adjustment of the lithosphere due to the localized loading. The velocity model also provides a robust framework for future earthquake location determinations and ground-shaking simulations for risk estimates.

Explaining Extreme Ground Motion in Osaka Basin during the 2011 Tohoku Earthquake

Despite being 770 km away from the epicenter, observed ground motions due to the Tohoku earthquake in the Osaka Basin were unexpectedly large, with an amplification of more than a factor of 20 compared to immediately outside the basin, and including 2.7 m peak-to-peak roof displacements at one high-rise building. The local ground motions exceeded expectations based on standard computations of site response by a factor of 3, predicted frequencies of peak acceleration were off by at least 50%, and such discrepancies have not yet been explained quantitatively. Here we show that utilizing semianalytic theory for surface-wave amplification, we are able to accurately predict both the amplitudes and frequencies of large ground amplification in the Osaka Basin using only knowledge of the local one-dimensional structure. Comparison between this simple prediction and observed amplification was not expected to be so favorable and suggests that simple one-dimensional surface-wave site amplification factors can be useful in the absence of full three-dimensional wave propagation simulations. Such surface-wave amplification factors can be included in addition to the standard measures of site-specific site amplification and should help explain strong ground motion variability in future large earthquakes that shake Osaka Basin and elsewhere in the world.

Amplification and Attenuation across USArray using Ambient Noise Wavefront Tracking

As seismic traveltime tomography continues to be refined using data from the vast USArray data set, it is advantageous to also exploit the amplitude information carried by seismic waves. We use ambient noise cross correlation to make observations of surface wave amplification and attenuation at shorter periods (8–32 s) than can be observed with only traditional teleseismic earthquake sources. We show that the wavefront tracking approach can be successfully applied to ambient noise correlations, yielding results quite similar to those from earthquake observations at periods of overlap. This consistency indicates that the wavefront tracking approach is viable for use with ambient noise correlations, despite concerns of the inhomogeneous and unknown distribution of noise sources. The resulting amplification and attenuation maps correlate well with known tectonic and crustal structure; at the shortest periods, our amplification and attenuation maps correlate well with surface geology and known sedimentary basins, while our longest period amplitudes are controlled by crustal thickness and begin to probe upper mantle materials. These amplification and attenuation observations are sensitive to crustal materials in different ways than traveltime observations and may be used to better constrain temperature or density variations. We also value them as an independent means of describing the lateral variability of observed Rayleigh wave amplitudes without the need for 3-D tomographic inversions.

A 3D Broadband Seismometer Array Experiment at the Homestake Mine

Seismometer deployments are often confined to near the Earth’s surface for practical reasons, despite the clear advantages of deeper seismometer installations related to lower noise levels and more homogeneous conditions. Here, we describe a 3D broadband seismometer array deployed at the inactive Homestake Mine in South Dakota, which takes advantage of infrastructure originally setup for mining and is now used for a range of scientific experiments. The array consists of 24 stations, of which 15 were underground, with depths ranging from 300 ft (91 m) to 4850 ft (1478 m), and with a 3D aperture of ∼1.5 km in each direction, thus spanning a 3D volume of about 3.4 km^3. We describe unique research opportunities and challenges related to the 3D geometry, including the generally low ambient noise levels, the strong coherency between observed event waveforms across the array, and the technical challenges of running the network. This article summarizes preliminary results obtained using data acquired by the Homestake array, illustrating the range of possible studies supported by the data.