Daniel M. Brum

Multivariate optimization of a liquid-liquid extraction of the EPA-PAHs from natural contaminated waters prior to determination by liquid chromatography with fluorescence detection.

This paper reports the multivariate optimization of a liquid-liquid extraction procedure for the determination of 15 EPA-polycyclic aromatic hydrocarbons (PAHs) by high-performance liquid chromatography with fluorescence detection. A Doehlert design was used to find optimum conditions for the procedure through Response Surface Methodology. Three variables (total volume of hexane, number of extraction steps and duration of such steps) were elected as factors in the optimization study. A principal component analysis (PCA) was run with optimized data, resulting in four groups of PAHs, ordered according to their molecular weight. Final working conditions were established in order to achieve a more robust methodology in relation to all fifteen PAHs under study. Best results could be observed when 77 mL of hexane were divided in four consecutive extraction steps with 18 min each. These experimental conditions were applied in the analysis of a spiked river water sample, and the recoveries varied between 80.9 and 106%, with an average value of 97.1+/-6.8%. The application of the methodology to river water showed that the method has a good average precision for the studied PAHs.

Application of the extraction induced by emulsion breaking for the determination of chromium and manganese in edible oils by electrothermal atomic absorption spectrometry.

This work reports the optimization of a method, based on the extraction induced by emulsion breaking, for the determination of trace concentrations of Cr and Mn in edible oils by electrothermal atomic absorption spectrometry (ETAAS). In the method, a water-in-oil emulsion was prepared by mixing the oil sample with an acid solution (HNO(3)) of Triton X-114 to allow the intense contact between the sample and the extractant acid solution. Afterwards, the emulsion was broken by heating and the acid aqueous phase deposited in the bottom of the flask was collected for the determination of the metals of interest. The method was optimized by studying the influence of several parameters such as the concentration of HNO(3) and the emulsifier agent (Triton X-100 and Triton X-114) in the extractant solution. The best results were verified when the procedure was performed with 5 mL of the sample and 1 mL of the extractant solution containing 15%m/v of Triton X-114 and 2.8 mol L(-1) of HNO(3). Also, the fastest emulsion breaking was verified when the emulsions were heated at 90°C. In these conditions, the emulsions were broken in approximately 10 min. The quantification of Cr and Mn in the extracts was carried out by external calibration with aqueous standard solutions, which simplified the procedure. The limits of detection for the determination of Cr and Mn in the oil samples were 66 and 36 ng L(-1), respectively, and the limits of quantification were 219 and 120 ng L(-1), respectively. The developed method was applied in the determination of Cr and Mn in twelve samples of edible oils produced with different oleaginous. Recovery tests were performed to attest the accuracy of the method, being observed recovery percentages in the range of 86-115%.

Novel extraction induced by emulsion breaking as a tool for the determination of trace concentrations of Cu, Mn and Ni in biodiesel by electrothermal atomic absorption spectrometry.

This work proposes a novel method for the determination of trace concentrations of Cu, Mn and Ni in biodiesel samples by electrothermal atomic absorption spectrometry. In order to overcome problems related to the organic matrix in the direct introduction of the samples, a new extraction approach was investigated. The method was based on the extraction induced by emulsion breaking, in which metals were transferred from the biodiesel to an acid aqueous phase after formation and breaking of a water-in-oil emulsion prepared by mixing the biodiesel sample with an aqueous solution containing surfactant and nitric acid. Several parameters that could influence the performance of the system were evaluated. Quantitative extractions of the analytes were obtained when the extraction was performed using an emulsifier solution containing 2.1 mol L(-1) of HNO3 and 7% m/v of Triton X-100. The extraction time had remarkable influence on the efficiency of the process, being necessary an agitation time of 60 min to achieve maximum extraction. The limits of quantification were below 1 µg L(-1) for the three analytes under study. The accuracy of the method was tested by application of a recovery test (recovery percentages between 89% and 109% were observed) and by comparison with a well-established method, taken as reference.

Application of the extraction induced by emulsion breaking for the determination of Cu, Fe and Mn in used lubricating oils by flame atomic absorption spectrometry.

A novel approach is proposed for the sample preparation of used lubricating oils to determine Cu, Fe and Mn by FAAS. The method is based on the extraction induced by emulsion breaking, in which the elements of interest are transferred to an aqueous phase before the measurement by FAAS. In the method, each sample of used lubricating oil was diluted with toluene (20% v/v) and the resulting solution was emulsified with a Triton X-114 solution containing HNO3. Further, the water-in-oil emulsion was broken by centrifugation for 30 min at 3500 rpm, originating a system with two well-separated phases: (i) the upper phase, containing the used lubricating oil diluted in toluene and (ii) the lower aqueous phase, containing the analytes that were extracted from oil. The lower phase was collected, diluted with water and the analytes were determined by FAAS. The optimization of the methodology was performed by studying the influence of different parameters that could affect the extraction efficiency such as the nature and concentration of the solvent used for sample dilution, the concentrations of HNO3 and Triton X-114 in the solution employed for emulsification and the operational conditions for extraction (extraction, centrifugation and sampling times). The limits of quantification for Cu, Fe and Mn were 2.9, 77 and 8.2 ng g(-1), respectively. The accuracy of the method was evaluated by comparison with the reference method based on the total digestion of the samples in a closed-vessel microwave oven. There were no statistical differences between the results obtained with the proposed method and the reference one, except for Fe in the cases where its concentration was higher than 80 µg g(-1).

Development of a focused ultrasound-assisted extraction method for the determination of trace concentrations of Cr and Mn in pharmaceutical formulations by ETAAS

This paper reports the development of a new method for the focused ultrasound extraction of Cr and Mn from pharmaceutical formulations and their determination by electrothermal atomic absorption spectrometry (ETAAS). The method was optimized by evaluating the influence of several variables such as the sonication power and time, concentration of HCl in the extractant solution and mass of sample employed in the extraction procedure. The curves of pyrolysis and atomization were constructed for both analytes in order to evaluate the effect of the matrix on the measurement of Cr and Mn. Quantitative extraction of both Cr and Mn was achieved when 25-150 mg of the sample were sonicated for 30 min at 50% power with 5 ml of a 1 moll(-1) HCl solution. The developed method was successfully applied in the determination of Cr and Mn in samples of pharmaceutical formulations containing different active principles such as ciprofloxacin, cephalexin, azithromycin, amlodipine and methionine. There was no statistical (95% confidence level, paired t-test) difference between the results obtained by the proposed method and the results obtained after total digestion of the samples.

Development of a method for total Hg determination in oil samples by cold vapor atomic absorption spectrometry after its extraction induced by emulsion breaking.

This work reports the development of a novel extraction method for total Hg determination in oil samples. After extracting Hg from samples it was quantified in the extracts by cold vapor atomic absorption spectrometry (CV-AAS), employing a laboratory-made gas-liquid separator (GLS) and NaBH4 as reducing agent. The extraction of Hg from samples was carried out by extraction induced by emulsion breaking (EIEB), which is based on the formation and breaking of water-in-oil emulsion between the oil samples and an extractant solution containing an emulsifying agent (surfactant) and nitric acid. Operational parameters of the GLS were evaluated in order to set the best performance of the measurement system. In these studies it was proven that the volume of sample and the concentration of HCl added to the sample extracts had significant influence on Hg response. The best conditions were achieved by adding 0.5 mL of a 0.3 mol L(-1) HCl solution on 1 mL of sample extract. The extraction conditions were also optimized. The highest efficiency was observed when 4 mL of a solution containing 2.5% triton X-100 and 15% v/v HNO3 were employed for the extraction of Hg contained in 20 mL of sample. Emulsion breaking was performed by heating at 80 °C and took approximately 20 min. The limit of quantification of the method was 1.9 µg L(-1) and recovery percentages between 80% and 103% were observed when spiked samples (2 and 10 µg L(-1)) of diesel oil, biodiesel and mineral oil were analyzed.

Polycyclic aromatic hydrocarbons in Tripuí River, Ouro Preto, MG, Brazil

This paper reports the determination of 15 EPA-polycyclic aromatic hydrocarbons (PAHs) and benzo[e]pyrene in water samples collected in Tripuí River, Ouro Preto City, MG, Brazil. Samples were collected between September 2006 (dry season) and November 2006 (wet season) in the neighborhood of an aluminum smelter. Detection limits and quantification limits were sufficiently low to accomplish PAH determination below the maximum concentration levels established by the Brazilian and USEPA legislations. Recoveries from water spiked samples were always larger than 89%. Fluoranthene, pyrene, phenanthrene, chrysene and benzo[b]fluoranthene predominated in the studied samples. The concentrations of PAHs upstream the aluminum smelter were systematically lower than those found downstream indicating a possible role of the smelter in the local pollution by PAHs. Principal component analysis and cluster analysis also showed remarkable differences of the characteristics of samples collected upstream and downstream the aluminum smelter and also of samples from wet and dry seasons.

Determination of metals in soft drinks packed in different materials by ETAAS

The present work proposes a method for the direct determination of Al, Cu, Cr, Fe and Ni in Brazilian carbonated soft drinks by electrothermal atomic absorption spectrometry (ETAAS). Samples of different flavors packed in containers made of different materials (polyterephthalate ethylene and glass bottles, and aluminum and steel cans) were analyzed. The method was optimized by building up pyrolysis and atomization curves in sample medium and by evaluating the calibration approach. Under optimized conditions, recoveries in the range of 92-104% were obtained in the evaluation of method accuracy. The limits of quantification for Al, Cu, Cr, Fe and Ni were 2.3, 0.93, 0.17, 0.90 and 1.2 μg L(-1), respectively. Also, the impact of the material used in the packaging and flavor on the concentrations of each metal in the samples was evaluated. It was proved that neither flavor nor packaging material affected the concentrations of Al and Fe in the samples. On the other hand, the packaging material influenced the concentration of Cu, Cr and Ni, and only the flavor affected the concentration of Cu in the samples. These conclusions were based on the data obtained from the application of a two-way ANOVA evaluation at 95% confidence level.

Superficial distribution of aromatic compounds and geomicrobiology of sediments from Suruí Mangrove, Guanabara Bay, RJ, Brazil

The distribution of selected aromatic compounds and microbiology were assessed in superficial sediments from Suruí Mangrove, Guanabara Bay. Samples were collected at 23 stations, and particle size, organic matter, aromatic compounds, microbiology activity, biopolymers, and topography were determined. The concentration of aromatic compounds was distributed in patches over the entire mangrove, and their highest total concentration was determinated in the mangroves central area. Particle size differed from most mangroves in that Suruí Mangrove has chernies on the edges and in front of the mangrove, and sand across the whole surface, which hampers the relationship between particle size and hydrocarbons. An average @ 10% p/p of organic matter was obtained, and biopolymers presented high concentrations, especially in the central and back areas of the mangrove. The biopolymers were distributed in high concentrations. The presence of fine sediments is an important factor in hydrocarbon accumulation. With high concentration of organic matter and biopolymers, and the topography with chernies and roots protecting the mangrove, calmer areas are created with the deposition of material transported by wave action. Compared to global distributions, concentrations of aromatic compounds in Suruí Mangrove may be classified from moderate to high, showing that the studied area is highly impacted.

Development of an ultrasonic slurry sampling method for the determination of Cu and Mn in antibiotic tablets by electrothermal atomic absorption spectrometry.

A new method is described for simple, efficient and rapid determination of Cu and Mn in tablets of antibiotics (ciprofloxacin and cephalexin) by electrothermal atomic absorption spectrometry (ETAAS) using slurry sampling. In order to optimize the procedure, several variables that could affect the performance of the method were investigated. In the best conditions, the tablets could be analyzed by introducing into the graphite tube 20 μl of a slurry prepared with approximately 90-100mg of the sample and 2 ml of a solution containing 5% m/v of Triton X-114 and 2.8 M of HNO(3). Before the introduction, the slurries were sonicated for 15 min at 40% of amplitude (130 W maximum power) with an ultrasonic probe. The developed method was applied in the determination of Cu and Mn in four samples, and the results were compared with those obtained by focused microwave acid digestion with aqua regia (1:3 mixture of HNO(3):HCl). There was no statistical difference between the obtained values at 95% confidence level when a paired Student t-test was applied.