Daniel M. Ward

Ceramic-on-ceramic bearings in total hip arthroplasty.

The ideal bearing surface for total hip arthroplasty still is being sought. This bearing would be durable, cost-effective, easy to implant, inert, and produce minimal wear debris. Ceramic-on-ceramic bearings have continued to evolve and have enjoyed success in many European centers throughout the past 3 decades. A limited number of early reports from the United States discouraged widespread acceptance and use of ceramic-on-ceramic total hip arthroplasty. Once critically analyzed most of the failures from the early reports are attributable to design and material specific flaws. Vast improvements have been made in ceramic manufacturing leading to even more superior wear characteristics and higher burst strengths. The case for alumina-on-alumina ceramic bearings is becoming stronger as data accumulate clinically and in vitro. In a multicenter, prospective and randomized study, an alumina-on-alumina ceramic bearing is compared with a cobalt chrome-on-polyethylene bearing. After as many as 48 months there has been no significant difference in clinical performance between the two study groups. No ceramic head fracture or ceramic bearing failure has occurred. Therefore, this new alumina-on-alumina ceramic bearing is a safe option for total hip arthroplasty and may provide a more durable prosthesis especially in young and active patients.

Use of a hydroxyapatite-coated stem in patients with Dorr Type C femoral bone.

Type C bone, as described by Dorr, exhibits both cellular and structural compromise, which presents a challenge for fixation of a total hip arthroplasty (THA). We evaluated the performance of the Omnifit® HA stem, a hydroxyapatite-coated titanium alloy stem, by retrospectively reviewing the clinical and radiographic data of 15 patients with femoral Type C bone who received the stem during primary THA between 1991 and 1994. The patients were followed a minimum of 9 years (mean, 11.5 years; range, 9-14 years). The average age at surgery was 54 years and the average body mass index was 28. Eight of the patients were men. The median Harris hip score was 94.5 points. Radiographically, two independent reviewers identified all patients as Type C bone. The average canal to calcar isthmus ratio was 0.74 (range, 0.65-0.95). At most recent followup, four patients demonstrated proximal osteolysis. Using plain radiography we detected no patients with distal osteolysis or subsidence. At 9 to 14 years, the stem has performed well in a selected series of patients with poor bone quality and the outcomes compare favorably with previously reported findings using this design of stem in other bone types. These results support the decision to use a hydroxyapatite-coated stem in patients with Type C bone.Level of Evidence: Level IV, therapeutic study. See the Guidelines for Authors for a complete description of levels of evidence.

Adverse Tissue Reactions in Modular Exchangeable Neck Implants: A Report of Two Cases

Dual-modular femoral stems with exchangeable necks theoretically allow optimization of hip joint biomechanics via selective restoration of femoral anteversion, offset, and limb length. A potential disadvantage is the possible generation of metal ions and debris by fretting and crevice corrosion at the additional stem-neck interface. We present 2 cases of early-onset adverse inflammatory tissue reactions as a result of accelerated corrosion at the stem-neck interface of a dual-modular implant, requiring subsequent revision of well-fixed components.

Corrosion and Adverse Local Tissue Reaction in One Type of Modular Neck Stem

Modular neck stems allow for optimization of joint biomechanics by restoring anteversion, offset, and limb length. A potential disadvantage is the generation of metal ions from fretting and crevice corrosion. We identified 118 total hip arthroplasty implanted with one type of dual-modular femoral component. Thirty-six required revision due to adverse local tissue reaction. Multivariate analysis isolated females and low offset necks as risk factors for failure. Kaplan-Meir analysis revealed small stem sizes failed at a higher rate during early follow-up period. Although the cobalt/chrome levels were higher in the failed group, these tests had low diagnostic accuracy for ALTR, while MRI scan was more sensitive. We conclude that the complications related to the use of dual modular stems of this design outweigh the potential benefits.

Spontaneous Modular Femoral Head Dissociation Complicating Total Hip Arthroplasty

Modular femoral heads have been used successfully for many years in total hip arthroplasty. Few complications have been reported for the modular Morse taper connection between the femoral head and trunnion of the stem in metal-on-polyethylene bearings. Although there has always been some concern over the potential for fretting, corrosion, and generation of particulate debris at the modular junction, this was not considered a significant clinical problem. More recently, concern has increased because fretting and corrosive debris have resulted in rare cases of pain, adverse local tissue reaction, pseudotumor, and osteolysis. Larger femoral heads, which have gained popularity in total hip arthroplasty, are suspected to increase the potential for local and systemic complications of fretting, corrosion, and generation of metal ions because of greater torque at the modular junction. A less common complication is dissociation of the modular femoral heads. Morse taper dissociation has been reported in the literature, mainly in association with a traumatic event, such as closed reduction of a dislocation or fatigue fracture of the femoral neck of a prosthesis. This report describes 3 cases of spontaneous dissociation of the modular prosthetic femoral head from the trunnion of the same tapered titanium stem because of fretting and wear of the Morse taper in a metal-on-polyethylene bearing. Continued clinical and scientific research on Morse taper junctions is warranted to identify and prioritize implant and surgical factors that lead to this and other types of trunnion failure to minimize complications associated with Morse taper junctions as hip implants and surgical techniques continue to evolve.

Effect of Preoperative Exercise on Postoperative Mobility in Obese Total Joint Replacement Patients

There has been a significant increase in obesity in the United States over the past 20 years. Reports in the literature identify the association of obesity-related osteoarthritis and the likelihood of future total hip arthroplasty (THA) and total knee arthroplasty (TKA) in this patient population. However, little is known about the effect of preoperative exercise on immediate postoperative mobility and discharge disposition in obese total joint replacement patients. The purpose of this study was to examine the effect of preoperative exercise in the obese total joint replacement patient on early postoperative mobility and discharge disposition. We retrospectively reviewed a consecutive series of patients with a body mass index (BMI) ≥30 kg/m(2) who underwent primary total joint replacement surgery from June 2005 through October 2005 at 1 institution. Two hundred seven patients met the inclusion criteria. Sixty-five patients performed self-reported preoperative exercise, defined as physical activity deemed above and beyond that of activities of daily living. Fewer exercise patients, 6.8%, required the assistance of ≥2 caregivers for mobility on postoperative day 1 vs 17.4% for nonexercisers. Fifty-four percent of patients participating in preoperative exercise were discharged home vs 46% who did not participate in exercise. A preoperative exercise program can improve postoperative functional mobility and increase the likelihood of discharge home in total joint replacement patients with a BMI of ≥30 kg/m(2).

Effect of Pelvic Tilt and Rotation on Cup Orientation in Both Supine and Standing Positions

BACKGROUND The purpose of this study is to analyze the effect of pelvic tilt and rotation on radiographic measurement of cup orientation. METHODS A total of 68 patients (79 hips) were included in this study. The patients had a computed tomography study and approximately 3 months of postoperative standing anteroposterior pelvic radiographs in both supine and standing positions. We used 2-dimensional (2D)/3-dimensional (3D) matching to measure pelvic tilt and rotation, and cup orientation. RESULTS There was a wide range of pelvic tilt between individuals in both supine and standing positions. Supine pelvic tilt was different from standing pelvic tilt (P < .05). There were differences in cup anteversion before and after 2D/3D matching in both supine and standing positions (P < .05). Supine and standing pelvic tilt correlated with differences in cup anteversion before and after 2D/3D matching. When all 79 hips were separated into right and left side, pelvic rotation inversely correlated with the pelvic tilt-adjusted difference in anteversion before and after 2D/3D matching of the right side but directly correlated with that of the left side in both supine and standing positions. CONCLUSION This study demonstrated that the measurement of cup anteversion on anteroposterior radiographs is significantly affected by both pelvic tilt and pelvic rotation (depending on the side). Improved understanding of pelvic orientation and improved ability to measure pelvic orientation may eventually allow for desired cup positioning to potentially protect against complications associated with malposition of the cup.