Daoli Zhao

Electrospun carbon nanofiber modified electrodes for stripping voltammetry.

Electrospun polyacrylonitrile (PAN) based carbon nanofibers (CNFs) have attracted intense attention due to their easy processing, high carbon yield, and robust mechanical properties. In this work, a CNF modified glassy carbon (GC) electrode that was coated with Nafion polymer was evaluated as a new electrode material for the simultaneous determination of trace levels of heavy metal ions by anodic stripping voltammetry (ASV). Pb(2+) and Cd(2+) were used as a representative system for this initial study. Well-defined stripping voltammograms were obtained when Pb(2+) and Cd(2+) were determined individually and then simultaneously in a mixture. Compared to a bare GC electrode, the CNF/Nafion modified GC (CNF/Nafion/GC) electrode improved the sensitivity for lead detection by 8-fold. The interface properties of the CNF/Nafion/GC were characterized by electrochemical impedance spectroscopy (EIS), which showed the importance of the ratio of CNF/Nafion on electrode performance. Under optimized conditions, the detection limits are 0.9 and 1.5 nM for Pb(2+) and Cd(2+), respectively.

Carbon nanotube-loaded Nafion film electrochemical sensor for metal ions: europium.

A Nafion film loaded with novel catalyst-free multiwalled carbon nanotubes (MWCNTs) was used to modify a glassy carbon (GC) electrode to detect trace concentrations of metal ions, with europium ion (Eu(3+)) as a model. The interaction between the sidewalls of MWCNTs and the hydrophobic backbone of Nafion allows the MWCNTs to be dispersed in Nafion, which was then coated as a thin film on the GC electrode surface. The electrochemical response to Eu(3+) was found to be ∼10 times improved by MWCNT concentrations between 0.5 and 2 mg/mL, which effectively expanded the electrode surface into the Nafion film and thereby reduced the diffusion distance of Eu(3+) to the electrode surface. At low MWCNT concentrations of 0.25 and 0.5 mg/mL, no significant improvement in signal was obtained compared with Nafion alone. Scanning electron microscopy and electrochemical impedance spectroscopy were used to characterize the structure of the MWCNT-Nafion film, followed by electrochemical characterization with Eu(3+) via cyclic voltammetry and preconcentration voltammetry. Under the optimized conditions, a linear range of 1-100 nM with a calculated detection limit of 0.37 nM (signal/noise = 3) was obtained for determination of Eu(3+) by Osteryoung square-wave voltammetry after a preconcentration time of 480 s.

Beyond graphene foam, a new form of three-dimensional graphene for supercapacitor electrodes

Graphene foam (GF) is a three-dimensional (3D) graphene structure that has been intensively studied as an electrode material for energy storage applications. The porous structure and seamlessly connected graphene flakes make GF a promising electrode material for supercapacitors and batteries. However, the electrical conductivity of GF is still unsatisfactory due to the lack of macropore size (∼300 μm) control that hinders its applications. Previously we reported a new seamless 3D graphene structure – graphene pellets (GPs) – with well-controlled mesopore size (∼2 nm), high electrical conductivity (148 S cm−1) and good electromechanical properties that differ substantially from the known GF. Here we demonstrate that the obtained 3D graphene structure is an ideal scaffold electrode for pseudocapacitive materials and redox additive electrolyte systems. For example, after electrochemical coating with MnO2, the GP/MnO2 electrode showed specific and volumetric capacitance up to 395 F g−1 and 230 F cm−3 at 1 A g−1, respectively. When combined with a hydroquinone and benzoquinone redox additive electrolyte, the GPs showed a specific capacitance of 7813 F g−1 at 10 A g−1. Moreover, when the GP/MnO2 electrode was assembled with a GP/polypyrrole electrode, the obtained full cell showed good electrochemical performance with a maximum energy density of 26.7 W h kg−1 and a maximum power density of 32.7 kW kg−1, and a reasonable cycle life for practical application. The ease in material processing combined with the excellent electrical and electromechanical properties makes GPs promising for a variety of energy storage applications.

In vivo monitoring the biodegradation of magnesium alloys with an electrochemical H2 sensor.

UNLABELLED Monitoring the biodegradation process of magnesium and its alloys in vivo is challenging. Currently, this process is monitored by micro-CT and X-ray imaging in vivo, which require large and costly instrumentation. Here we report a simple and effective methodology to monitor the biodegradation process in vivo by sensing H2 transdermally above a magnesium sample implanted subcutaneously in a mouse. An electrochemical H2 microsensor was used to measure the biodegradation product H2 at the surface of the skin for two magnesium alloys (ZK40 and AZ31) and one high purity magnesium single crystal (Mg8H). The sensor was able to easily detect low levels of H2 (30-400μM) permeating through the skin with a response time of about 30s. H2 levels were correlated with the biodegradation rate as determined from weight loss measurements of the implants. This new method is noninvasive, fast and requires no major equipment. STATEMENT OF SIGNIFICANCE Biomedical devices such as plates and screws used for broken bone repair are being developed out of biodegradable magnesium alloys that gradually dissolve when no longer needed. This avoids subsequent removal by surgery, which may be necessary if complications arise. A rapid, non-invasive means for monitoring the biodegradation process in vivo is needed for animal testing and point of care (POC) evaluation of patients. Here we report a novel, simple, fast, and noninvasive method to monitor the biodegradation of magnesium in vivo by measuring the biodegradation product H2 with an electrochemical H2 sensor. Since H2 rapidly permeates through biological tissue, measurements are made by simply pressing the sensor tip against the skin above the implant; the response is within 30s.

In vivo characterization of magnesium alloy biodegradation using electrochemical H2 monitoring, ICP-MS, and XPS

The effect of widely different corrosion rates of Mg alloys on four parameters of interest for in vivo characterization was evaluated: (1) the effectiveness of transdermal H2 measurements with an electrochemical sensor for noninvasively monitoring biodegradation compared to the standard techniques of in vivo X-ray imaging and weight loss measurement of explanted samples, (2) the chemical compositions of the corrosion layers of the explanted samples by XPS, (3) the effect on animal organs by histology, and (4) the accumulation of corrosion by-products in multiple organs by ICP-MS. The in vivo biodegradation of three magnesium alloys chosen for their widely varying corrosion rates - ZJ41 (fast), WKX41 (intermediate) and AZ31 (slow) - were evaluated in a subcutaneous implant mouse model. Measuring H2 with an electrochemical H2 sensor is a simple and effective method to monitor the biodegradation process in vivo by sensing H2 transdermally above magnesium alloys implanted subcutaneously in mice. The correlation of H2 levels and biodegradation rate measured by weight loss shows that this non-invasive method is fast, reliable and accurate. Analysis of the insoluble biodegradation products on the explanted alloys by XPS showed all of them to consist primarily of Mg(OH)2, MgO, MgCO3 and Mg3(PO4)2 with ZJ41 also having ZnO. The accumulation of magnesium and zinc were measured in 9 different organs by ICP-MS. Histological and ICP-MS studies reveal that there is no significant accumulation of magnesium in these organs for all three alloys; however, zinc accumulation in intestine, kidney and lung for the faster biodegrading alloy ZJ41 was observed. Although zinc accumulates in these three organs, no toxicity response was observed in the histological study. ICP-MS also shows higher levels of magnesium and zinc in the skull than in the other organs. STATEMENT OF SIGNIFICANCE Biodegradable devices based on magnesium and its alloys are promising because they gradually dissolve and thereby avoid the need for subsequent removal by surgery if complications arise. In vivo biodegradation rate is one of the crucial parameters for the development of these alloys. Promising alloys are first evaluated in vivo by being implanted subcutaneously in mice for 1month. Here, we evaluated several magnesium alloys with widely varying corrosion rates in vivo using multiple characterization techniques. Since the alloys biodegrade by reacting with water forming H2 gas, we used a recently demonstrated, simple, fast and noninvasive method to monitor the biodegradation process by just pressing the tip of a H2 sensor against the skin above the implant. The analysis of 9 organs (intestine, kidney, spleen, lung, heart, liver, skin, brain and skull) for accumulation of Mg and Zn revealed no significant accumulation of magnesium in these organs. Zinc accumulation in intestine, kidney and lung was observed for the faster corroding implant ZJ41. The surfaces of explanted alloys were analyzed to determine the composition of the insoluble biodegradation products. The results suggest that these tested alloys are potential candidates for biodegradable implant applications.

Visual H2 sensor for monitoring biodegradation of magnesium implants in vivo

A visual sensor for H2 was used to transdermally monitor H2 that originated from biodegrading magnesium (Mg) alloys implanted subcutaneously in mice. The visual sensor consisted of a thin film of H2-sensitive material (MoO3 and Pd catalyst) coated on a flexible plastic sheet that was pressed against the mouse skin directly above the implant. Although the H2 levels permeating through the skin during the degradation process were very low, the sensor changed color to give a three dimensional (3D) visualization of H2 permeation. The correlation between the visual sensor response and measurements made with an electrochemical H2 microsensor on several magnesium alloys demonstrates that the visual sensor has the capability to monitor in real-time the dissolution rate of implants in vivo. This detection method is noninvasive, easy to implement, effective and potentially low cost compared to electrochemical detection. STATEMENT OF SIGNIFICANCE Biodegradable Mg implants offer advantages over permanent implants such as stainless steel that are used for broken bone repair. Mg alloys gradually dissolve, avoiding the need for removal by a later surgery if complications arise. Here we report a visual H2 sensor that can be used in the research laboratory to monitor the corrosion process in vivo during animal testing of different Mg alloys. The sensor consists of a plastic sheet with a thin coating that changes color in the presence of H2 gas. The sensor is easily used by taping it on the skin over the Mg implant. The color change gives a map of the H2 level permeating from the degrading Mg through the skin above it. This low cost, simple method of monitoring the dissolution of biodegradable implants would greatly facilitate the development of the biodegradable materials, especially in animal studies where in vivo biodegradation is tested.

A Corrugated Graphene–Carbon Nanotube Composite as Electrode Material

A graphene and carbon nanotube (CNT) array composite was synthesized by chemical vapor deposition (CVD) and chemically treated after synthesis, yielding a novel corrugated structure, visually similar to a mushroom gill. This binder-free hybrid material was used to make an electrode that may find application in energy storage devices, such as supercapacitors. The electrode performance of the corrugated graphene/CNT array composite (CGCC) was compared to that of commercial glassy carbon. The results of the comparison are presented here, along with suggestions for further development of the CGCC electrode.

Carbon Nanotube Thread Electrochemical Cell: Detection of Heavy Metals

In this work, all three electrodes in an electrochemical cell were fabricated based on carbon nanotube (CNT) thread. CNT thread partially insulated with a thin polystyrene coating to define the microelectrode area was used as the working electrode; bare CNT thread was used as the auxiliary electrode; and a micro quasi-reference electrode was fabricated by electroplating CNT thread with Ag and then anodizing it in chloride solution to form a layer of AgCl. The Ag|AgCl coated CNT thread electrode provided a stable potential comparable to the conventional liquid-junction type Ag|AgCl reference electrode. The CNT thread auxiliary electrode provided a stable current, which is comparable to a Pt wire auxiliary electrode. This all-CNT thread three electrode cell has been evaluated as a microsensor for the simultaneous determination of trace levels of heavy metal ions by anodic stripping voltammetry (ASV). Hg2+, Cu2+, and Pb2+ were used as a representative system for this study. The calculated detection limits (based on the 3σ method) with a 120 s deposition time are 1.05, 0.53, and 0.57 nM for Hg2+, Cu2+, and Pb2+, respectively. These electrodes significantly reduce the dimensions of the conventional three electrode electrochemical cell to the microscale.

In vivo quantification of hydrogen gas concentration in bone marrow surrounding magnesium fracture fixation hardware using an electrochemical hydrogen gas sensor

Magnesium (Mg) medical devices are currently being marketed for orthopedic applications and have a complex degradation process which includes the evolution of hydrogen gas (H2). The effect of H2 exposure on relevant cell types has not been studied; and the concentration surrounding degrading Mg devices has not been quantified to enable such mechanistic studies. A simple and effective method to measure the concentration of H2 in varying microenvironments surrounding Mg implants is the first step to understanding the biological impact of H2 on these cells. Here, the in vivo measurement of H2 surrounding fracture fixation devices implanted in vivo is demonstrated. An electrochemical H2 microsensor detected increased levels of H2 at three anatomical sites with a response time of about 30 s. The sensor showed the H2 concentration in the bone marrow at 1 week post-implantation (1460 ± 320 µM) to be much higher than measured in the subcutaneous tissue (550 ± 210 µM) and at the skin surface (120 ± 50 µM). Additionally, the H2 concentrations measured in the bone marrow exceeded the concentration in a H2 saturated water solution (∼800 µM). These results suggest that H2 emanating from Mg implants in bone during degradation pass through the bone marrow and become at least partially trapped because of slow permeation through the bone. This study is the first to identify H2 concentrations in the bone marrow environment and will enable in vitro experiments to be executed at clinically relevant H2 concentrations to explore possible biological effects of H2 exposure. STATEMENT OF SIGNIFICANCE An electrochemical H2 sensor was used to monitor the degradation of a Mg fracture fixation system in a lapine ulna fracture model. Interestingly, the H2 concentration in the bone marrow is 82% higher than H2 saturated water solution. This suggests H2 generated in situ is trapped in the bone marrow and bone is less permeable than the surrounding tissues. The detectable H2 at the rabbit skin also demonstrates a H2 sensors ability to monitor the degradation process under thin layers of tissue. H2 sensing shows promise as a tool for monitoring the degradation of Mg alloy in vivo and creating in vitro test beds to more mechanistically evaluate the effects of varying H2 concentrations on cell types relevant to osteogenesis.