David P. Allison

THERMAL AND AMBIENT-INDUCED DEFLECTIONS OF SCANNING FORCE MICROSCOPE CANTILEVERS

The deflection of scanning force microscope cantilevers, metal coated on one side, is significantly influenced by both thermal heating and variations in relative humidity. For constant relative humidity, the deflection of the cantilever drifts due to laser heating and eventually reaches a steady‐state value. For a thermally stabilized cantilever, the deflection varies linearly with relative humidity. Exposure to other vapors, such as mercury, changes the inherent deflection of the cantilever. Relative amounts of adsorbates on the cantilever can be estimated from shifts in the cantilever resonance frequency with picogram mass resolution. The cantilever deflection as well as changes in resonance frequency due to vapor adsorption can be used as basis for novel chemical sensors.

Resonance response of scanning force microscopy cantilevers

A variational method is used to calculate the deflection and the fundamental and harmonic resonance frequencies of commercial V‐shaped and rectangular atomic force microscopy cantilevers. The effective mass of V‐shaped cantilevers is roughly half that calculated for the equivalent rectangular cantilevers. Damping by environmental gases, including air, nitrogen, argon, and helium, affects the frequency of maximum response and to a much greater degree the quality factor Q. Helium has the lowest viscosity, resulting in the highest Q, and thus provides the best sensitivity in noncontact force microscopy. Damping in liquids is dominated by an increase in effective mass of the cantilever due to an added mass of the liquid being dragged with that cantilever.

Silver nanocrystallites: biofabrication using Shewanella oneidensis, and an evaluation of their comparative toxicity on gram-negative and gram-positive bacteria.

Microorganisms have long been known to develop resistance to metal ions either by sequestering metals inside the cell or by effluxing them into the extracellular media. Here we report the biosynthesis of extracellular silver-based single nanocrystallites of well-defined composition and homogeneous morphology utilizing the gamma-proteobacterium, Shewanella oneidensis MR-1, upon incubation with aqueous silver nitrate solution. Further characterization of these particles revealed that the crystals consist of small, reasonably monodispersed spheres in the 2-11 nm size range (average of 4 +/- 1.5 nm). The bactericidal effect of these nanoparticles (biogenic-Ag) is compared to chemically synthesized silver nanoparticles (colloidal-Ag and oleate capped silver nanoparticles, oleate-Ag) and assessed using Gram-negative (E. coli and S. oneidensis) and Gram-positive (B. subtilis) bacteria. Relative toxicity was based on the diameter of inhibition zone in disk diffusion tests, minimum inhibitory concentrations, live/dead assays, and atomic force microscopy. From a toxicity perspective, strain-dependent inhibition depended on the synthesis procedure and the surface coat. Biogenic-Ag was found to be of higher toxicity compared to colloidal-Ag for all three strains tested, whereas E. coli and S. oneidensis were found to be more resistant to either of these nanoparticles than B. subtilis. In contrast, oleate-Ag was not toxic to any of the bacteria. These findings have implications for the potential uses of Ag nanomaterials and for their fate in biological and environmental systems.

Effects of Engineered Cerium Oxide Nanoparticles on Bacterial Growth and Viability

ABSTRACT Interest in engineered nanostructures has risen in recent years due to their use in energy conservation strategies and biomedicine. To ensure prudent development and use of nanomaterials, the fate and effects of such engineered structures on the environment should be understood. Interactions of nanomaterials with environmental microorganisms are inevitable, but the general consequences of such interactions remain unclear, due to a lack of standard methods for assessing such interactions. Therefore, we have initiated a multianalytical approach to understand the interactions of synthesized nanoparticles with bacterial systems. These efforts are focused initially on cerium oxide nanoparticles and model bacteria in order to evaluate characterization procedures and the possible fate of such materials in the environment. The growth and viability of the Gram-negative species Escherichia coli and Shewanella oneidensis, a metal-reducing bacterium, and the Gram-positive species Bacillus subtilis were examined relative to cerium oxide particle size, growth media, pH, and dosage. A hydrothermal synthesis approach was used to prepare cerium oxide nanoparticles of defined sizes in order to eliminate complications originating from the use of organic solvents and surfactants. Bactericidal effects were determined from MIC and CFU measurements, disk diffusion tests, and live/dead assays. For E. coli and B. subtilis, clear strain- and size-dependent inhibition was observed, whereas S. oneidensis appeared to be unaffected by the particles. Transmission electron microscopy along with microarray-based transcriptional profiling was used to understand the response mechanism of the bacteria. Use of multiple analytical approaches adds confidence to toxicity assessments, while the use of different bacterial systems highlights the potential wide-ranging effects of nanomaterial interactions in the environment.

AFM imaging of bacteria in liquid media immobilized on gelatin coated mica surfaces

Immobilization of particulates, especially biomolecules and cells, onto surfaces is critical for imaging with the atomic force microscope (AFM). In this paper, gelatin coated mica surfaces are shown to be suitable for immobilizing and imaging both gram positive, Staphylococcus aureus, and gram negative, Escherichia coli, bacteria in both air and liquid environments. Gelatin coated surfaces are shown to be superior to poly-L-lysine coated surfaces that are commonly used for the immobilization of cells. This cell immobilization technique is being developed primarily for live cell imaging of Rhodopseudomonas palustris. The genome of R. palustris has been sequenced and the organism is the target of intensive studies aimed at understanding genome function. Images of R. palustris grown both aerobically and anaerobically in liquid media are presented. Images in liquid media show the bacteria is rod shaped and smooth while images in air show marked irregularity and folding of the surface. Significant differences in the vertical dimension are also apparent with the height of the bacteria in liquid being substantially greater than images taken in air. In air immobilized bacterial flagella are clearly seen while in liquid this structure is not visible. Additionally, significant morphological differences are observed that depend on the method of bacterial growth.

Biofabrication of discrete spherical gold nanoparticles using the metal-reducing bacterium, Shewanella oneidensis

Nanocrystallites have garnered substantial interest due to their various applications, including catalysis and medical research. Consequently important aspects of synthesis related to control of shape and size through economical and non-hazardous means are desirable. Highly efficient bioreduction-based fabrication approaches that utilize microbes and/or plant extracts are poised to meet these needs. Here we show that the γ-proteobacterium Shewanella oneidensis can reduce tetrachloroaurate (III) ions to produce discrete extracellular spherical gold nanocrystallites. The particles were homogeneously shaped with multiple size distributions and produced under ambient conditions at high yield, 88% theoretical maximum. Further characterization revealed that the particles consist of spheres in the size range of ∼2-50 nm, with an average size of 12±5 nm. The nanoparticles were hydrophilic and resisted aggregation even after several months. Based on our experiments, the particles are likely fabricated by the aid of reducing agents present in the bacterial cell membrane and are capped by a detachable protein/peptide coat. Ultraviolet-visible and Fourier transform infrared spectroscopy, X-ray diffraction, energy dispersive X-ray spectra and transmission electron microscopy measurements confirmed the formation, surface characteristics and crystalline nature of the nanoparticles. The antibacterial activity of these gold nanoparticles was assessed using Gram-negative (Escherichia coli and S. oneidensis) and Gram-positive (Bacillus subtilis) bacterial species. Toxicity assessments showed that the particles were neither toxic nor inhibitory to any of these bacteria.

Atomic force microscopy of biological samples

The ability to evaluate structural-functional relationships in real time has allowed scanning probe microscopy (SPM) to assume a prominent role in post genomic biological research. In this mini-review, we highlight the development of imaging and ancillary techniques that have allowed SPM to permeate many key areas of contemporary research. We begin by examining the invention of the scanning tunneling microscope (STM) by Binnig and Rohrer in 1982 and discuss how it served to team biologists with physicists to integrate high-resolution microscopy into biological science. We point to the problems of imaging nonconductive biological samples with the STM and relate how this led to the evolution of the atomic force microscope (AFM) developed by Binnig, Quate, and Gerber, in 1986. Commercialization in the late 1980s established SPM as a powerful research tool in the biological research community. Contact mode AFM imaging was soon complemented by the development of non-contact imaging modes. These non-contact modes eventually became the primary focus for further new applications including the development of fast scanning methods. The extreme sensitivity of the AFM cantilever was recognized and has been developed into applications for measuring forces required for indenting biological surfaces and breaking bonds between biomolecules. Further functional augmentation to the cantilever tip allowed development of new and emerging techniques including scanning ion-conductance microscopy (SICM), scanning electrochemical microscope (SECM), Kelvin force microscopy (KFM) and scanning near field ultrasonic holography (SNFUH).

Biomolecular force measurements and the atomic force microscope

The atomic force microscope (AFM) is a surface-sensitive instrument capable of imaging biological samples at nanometer resolution in all environments including liquids. The sensitivity of the AFM cantilever, to forces in the pico Newton range, has been exploited to measure breakaway forces between biomolecules and to measure folding-unfolding forces within single proteins. By attaching specific antibodies to cantilevers the simultaneous imaging of target antigens and identification of antigen-antibody interactions have been demonstrated.

Atomic force microscopy of deoxyribonucleic acid strands adsorbed on mica: The effect of humidity on apparent width and image contrast

We have investigated the effect of relative humidity on the apparent width and contrast of isolated strands of deoxyribonucleic acid (DNA) imaged with atomic force microscopy (AFM). Due to convolution of the tip with DNA, the apparent width of DNA molecules observed with AFM was broader than the known width of DNA. Also, the apparent width of DNA increased with increasing humidity while the contrast of the DNA images decreased with increasing humidity. This phenomenon is completely reversible and can be attributed to non‐normal forces causing a buckling of AFM cantilever.

Friction effects in the deflection of atomic force microscope cantilevers

The conventional deflection‐mode atomic force microscope operates by optically monitoring the slope near the end of a microcantilever in contact with the sample surface. This signal is usually interpreted as a measure of height change. Lateral forces from friction, surface geometry, or inclination of the cantilever to the surface also affect the slope due to cantilever buckling. We calculate the deflection of a hollow triangular model cantilever subject to both lateral and normal forces. The measured response of the servo circuit to an inclined, loaded cantilever is then determined. This shows (1) errors are always present in height measurements of structures on inhomogeneous surfaces; (2) the sensitivity to buckling can be reduced by repositioning the laser; (3) friction measurements can be accurately made by scanning in two directions and applying the proper calibration.