Dengbin Yu

Cell-based biosensor for measurement of phenol and nitrophenols toxicity

A cost-effective whole cell biosensor based on electrochemical technique to detect toxicities of phenol and nitrophenols has been developed. This method relied on the inhibition effect for respiratory chain activity of microorganism by toxicant, which was measured by chronoamperometry using mediator (ferricyanide). The current signals produced by suspended microorganisms and reoxidation of ferrocyanide were transformed to inhibiting efficiency directly, and 50% inhibiting concentration (IC(50)) was chosen as the quantitative standard of toxicity. The test microorganisms used here consist of three bacilli (Escherichia coli, Enterobacter cloacae and Alcaligenes faecalis), two pseudomonas (Pseudomonas fluorescens and Pseucomonas putida) and one fungus (Trichosporon cutaneum). 3,5-Dichlorophenol (DCP) was taken as the reference toxicant. The results showed that the microorganisms which belong to the same bacterial family had similar trends of inhibitions on respiratory activity and similar IC50 values. By comparing the IC(50) values, P. fluorescens was the most sensitive one to DCP toxicity, its IC(50) was estimated to be 4.2mg/L. pH 7.0 and together with the standard glucose-glutamic acid (GGA) as an exogenous material were taken for optimum conditions in this study. Here, P. fluorescens as model test microorganism was employed to assess toxicities of phenol and nitrophenols under the optimum conditions. IC(50) values of 291.4 mg/L for phenol, 64.1mg/L for 2-NP, 71.4 mg/L for 3-NP and 14.0mg/L for 4-NP were determined at 60 min, respectively. Comparison with the results of published data has confirmed that this cell biosensor is a sensitive and rapid alternative to toxicity screening of chemicals.

Immobilized multi-species based biosensor for rapid biochemical oxygen demand measurement

To improve the practicability of rapid biochemical oxygen demand (BOD) method, we proposed a stable BOD sensor based on immobilizing multi-species BODseed for wastewater monitoring in the flow system. The activation time of the biofilm was greatly shortened for the biofilm prepared by BODseed in the organic-inorganic hybrid material. Some influence factors such as temperature, pH, and concentration of phosphate buffer solution (PBS) were investigated in detail in which high tolerance to environment was validated for the BOD sensor permitted a wide pH and PBS concentration ranges. The minimum detectable BOD was around 0.5 mg/l BOD under the optimized 1.0 mg/ml BODseed immobilized concentration. The as-prepared BOD sensor exhibited excellent stability and reproducibility for different samples. Furthermore, the as-prepared BOD biosensor displayed a notable advantage in indiscriminate biodegradation to different organic compounds and their mixture, similar to the character of conventional BOD(5) results. The results of the BOD sensor method are well agreed with those obtained from conventional BOD(5) method for wastewater samples. The proposed rapid BOD sensor method should be promising in practical application of wastewater monitoring.

A sensitive, rapid and inexpensive way to assay pesticide toxicity based on electrochemical biosensor

We reported a rapid toxicity assay method using electrochemical biosensor for pesticides, Escherichia coli (E. coli) was taken as a model microorganism for test. In this method, we adopted ferricyanide instead of natural electron acceptor O(2), and then microbial oxidation was substantially accelerated. Toxicity assays measured the effect of toxic materials on the metabolic activity of microorganisms. The current signal of ferrocyanide produced from the metabolism was proven to be directly related to the toxicity, which could be amplified by ultramicroelectrode array (UMEA). The ratio of the electrochemical signals, recorded in the presence and absence of toxin, provided an index of inhibition. Accordingly, a direct toxicity assessment (DTA) based on chronoamperometry was proposed to detect the effect of toxic chemicals on microorganisms. 3,5-Dichlorophenol (DCP) was taken as the reference toxicant, its IC50 was estimated to be 8.0mg/L. Three pesticides were examined using this method. IC50 values of 6.5mg/L for Ametryn, 22 mg/L for Fenamiphos and 5.7 mg/L for Endosulfan were determined and in line with EC50 values reported in the literature. Atomic force microscopy (AFM) was also used for morphology characterization of E. coli induced by three pesticides. These results confirmed the present electrochemical method used is reliable. In addition, the electrochemical method is a sensitive, rapid and inexpensive way for toxicity assays of pesticides.

Development of a simple method for biotoxicity measurement using ultramicroelectrode array under non-deaerated condition.

In this paper, a mediated method by using ferricyanide under non-deaerated condition for biotoxicity measurement was proposed. Ultramicroelectrode array (UMEA) was employed for effectively amplify the electrochemical signal from the total limiting currents to distinguish a little change in toxicity. Five species of microorganisms including two bacilli (Escherichia coli and Enterobacter cloacae), two pseudomonas (Pseudomonas fluorescens and Pseucomonas putida) and one fungus (Trichosporon cutaneum) were employed. 3,5-dichlorophenol (DCP) was taken as the reference toxicant. The IC50 values we obtained were similar with the values obtained using in the deaerated method. E. coli was used as model test microorganism. The final concentration of ferricyanide is 45 mM, E. coli OD600 8 and 1 h incubation were taken in optimum conditions in this study. Four heavy metal ions (Cr(6+), Hg(2+), Cd(2+) and Bi(3+)) were examined under the optimum conditions. Comparison with the results reported previously has confirmed that this method provided a simple and rapid alternative to toxicity screening of chemicals, especially advantageous for in situ monitoring of water system.

Toxicity detection in water containing heavy metal ions with a self-powered microbial fuel cell-based biosensor

In this work, a self-powered microbial fuel cell (MFC)-based biosensor was developed for detecting toxicity in water containing heavy metal ions. Experimental conditions containing concentration of potassium ferricyanide, load resistor and glucose concentration were optimized. Six heavy metal ions (2mg/L, Cu2+, Hg2+, Zn2+, Cd2+, Pb2+ and Cr3+) were tested by this biosensor and the inhibition ratios obtained were 12.56%, 13.99%, 8.81%, 9.29%, 5.59% and 1.95%, respectively. The inhibition ratios of 28.13% was also obtained for detecting the laboratory wastewater containing several heavy metal ions. The experimental results exhibited the feasibility and potential of the self-powered biosensor in detecting toxicities in water containing heavy metal ions.

Toxicity detection of sodium nitrite, borax and aluminum potassium sulfate using electrochemical method

Based on the inhibition effect on the respiratory chain activity of microorganisms by toxicants, an electrochemical method has been developed to measure the current variation of a mediator in the presence of microorganisms contacted with a toxicant. Microelectrode arrays were adopted in this study, which can accelerate the mass transfer rate of an analyte to the electrode and also increase the total current signal, resulting in an improvement in detection sensitivity. We selected Escherichia coli as the testee and the standard glucose-glutamic acid as an exogenous material. Under oxygen restriction, the experiments in the presence of toxicant were performed at optimum conditions (solution pH 7.0, 37 degrees C and reaction for 3 hr). The resulting solution was then separated from the suspended microorganisms and was measured by an electrochemical method, using ferricyanide as a mediator. The current signal obtained represents the reoxidation of ferrocyanide, which was transformed to inhibiting efficiency, IC50, as a quantitative measure of toxicity. The IC50 values measured were 410, 570 and 830 mg/L for sodium nitrite, borax and aluminum potassium sulfate, respectively. The results show that the toxicity sequence for these three food additives is consistent with the value reported by other methods. Furthermore, the order of damage degree to the microorganism was also observed to be: sodium nitrite > borax > aluminum potassium sulfate > blank, according to the atomic force microscopy images of E. coli after being incubated for 3 hr with the toxic compound in buffer solutions. The electrochemical method is expected to be a sensitive and simple alternative to toxicity screening for chemical food additives.

Small Microbial Three-Electrode Cell Based Biosensor for Online Detection of Acute Water Toxicity

The monitoring of toxicity of water is very important to estimate the safety of drinking water and the level of water pollution. Herein, a small microbial three-electrode cell (M3C) biosensor filled with polystyrene particles was proposed for online monitoring of the acute water toxicity. The peak current of the biosensor related with the performance of the bioanode was regarded as the toxicity indicator, and thus the acute water toxicity could be determined in terms of inhibition ratio by comparing the peak current obtained with water sample to that obtained with nontoxic standard water. The incorporation of polystyrene particles in the electrochemical cell not only reduced the volume of the samples used, but also improved the sensitivity of the biosensor. Experimental conditions including washing time with PBS and the concentration of sodium acetate solution were optimized. The stability of the M3C biosensor under optimal conditions was also investigated. The M3C biosensor was further examined by formaldehyde at the concentration of 0.01%, 0.03%, and 0.05% (v/v), and the corresponding inhibition ratios were 14.6%, 21.6%, and 36.4%, respectively. This work provides a new insight into the development of an online toxicity detector based on M3C biosensor.

Biochemical oxygen demand measurement by mediator method in flow system

Using mediator as electron acceptor for biochemical oxygen demand (BOD) measurement was developed in the last decade (BODMed). However, until now, no BOD(Med) in a flow system has been reported. This work for the first time describes a flow system of BOD(Med) method (BOD(Med)-FS) by using potassium ferricyanide as mediator and carbon fiber felt as substrate material for microbial immobilization. The system can determine the BOD value within 30 min and possesses a wider analytical linear range for measuring glucose-glutamic acid (GGA) standard solution from 2 up to 200 mg L(-1) without the need of dilution. The analytical performance of the BOD(Med)-FS is comparable or better than that of the previously reported BOD(Med) method, especially its superior long-term stability up to 2 months under continuous operation. Moreover, the BOD(Med)-FS has same determination accuracy with the conventional BOD5 method by measuring real samples from a local wastewater treatment plant (WWTP).

Detecting total toxicity in water using a mediated biosensor system with flow injection

A novel total toxicity detection method based on a mediated biosensor system with flow injection (MB-FI) was developed to rapidly and reliably detect respiration inhibitors (i.e., As2O3, KCN, salicylic acid (SA), 2,4-dintirophenol (DNP)) in water. The mediated biosensor toxicity assessment using microorganisms immobilized in calcium alginate filaments can greatly simplify the testing process and save time. In the MB-FI system, ferricyanide together with a respiration inhibitor was injected into the bioreactor, inhibiting the respiration of the immobilized microorganisms. The degree of inhibition was measured by determining the ferrocyanide generated in the effluent, expressed as the 50% inhibition concentration (IC50). The IC50 values for the four respiration inhibitors obtained using this method were comparable to those obtained using the classic method, confirming that this approach is an alternative alert method. More importantly, this constructed biosensor system with flow injection will facilitate the application and commercialization of this toxicity monitoring technology.

Preparation, performance, and application of a stable, sensitive and cost-effective microelectrode array

The development of rapid toxicity detection technology has higher requirements for electrode. In this work, a stable, sensitive and cost-effective microelectrode array (MEA) was successfully prepared manually. The advantage of the as-prepared MEA was discussed by means of detecting toxicity of 3,5-Dichlorophenol (3,5-DCP) by contrasting with bulk electrode and single microelectrode, in which mixed microorganisms were selected as biocatalyst, and K3[Fe(CN)6] was adopted as electron mediator. The current reached a stable state in 10 s under the constant potential of 450 mV. The feasibility of rapid detection of toxicity of formaldehyde with the MEA was further verified. The current responses were analyzed over formaldehyde of the final concentrations varied from 0.0036% to 1.0%, and the traditional parameter of 50% inhibitory concentration (IC50) of 0.11% was obtained within 1 h. In brief, the as-prepared MEA has high sensitivity, good stability, strong anti-interference, and well corrosion resistance. It shows a very large application prospects in toxicity detection in water.