Desta Antenehe Gedefaw

A new tetracyclic lactam building block for thick, broad-bandgap photovoltaics.

A new tetracyclic lactam building block for polymer semiconductors is reported that was designed to combine the many favorable properties that larger fused and/or amide-containing building blocks can induce, including improved solid-state packing, high charge carrier mobility, and improved charge separation. Copolymerization with thiophene resulted in a semicrystalline conjugated polymer, PTNT, with a broad bandgap of 2.2 eV. Grazing incidence wide-angle X-ray scattering of PTNT thin films revealed a strong tendency for face-on π-stacking of the polymer backbone, which was retained in PTNT:fullerene blends. Corresponding solar cells featured a high open-circuit voltage of 0.9 V, a fill factor around 0.6, and a power conversion efficiency as high as 5% for >200 nm thick active layers, regardless of variations in blend stoichiometry and nanostructure. Moreover, efficiencies of >4% could be retained when thick active layers of ∼400 nm were employed. Overall, these values are the highest reported for a conjugated polymer with such a broad bandgap and are unprecedented in materials for tandem and particularly ternary blend photovoltaics. Hence, the newly developed tetracyclic lactam unit has significant potential as a conjugated building block in future organic electronic materials.

Conjugated polymers based on benzodithiophene and fluorinated quinoxaline for bulk heterojunction solar cells: thiophene versus thieno[3,2-b]thiophene as π-conjugated spacers

Two conjugated donor–acceptor copolymers based on a benzodithiophene donor unit and a fluorinated quinoxaline acceptor unit, spaced with either thiophene or thieno[3,2-b]thiophene π-bridges, were designed and synthesized. The effect of different π-bridges and of the processing conditions on optical, electrical, morphological and photovoltaic properties of the polymer:fullerene blend films were investigated. The polymer containing the thieno[3,2-b]thiophene π-bridge (PBDTFQ-TT) showed a red-shifted absorption and an enhanced charge carrier mobility, as compared to its analogue with the thiophene π-bridge (PBDTFQ-T), due to its narrower optical gap (by ∼0.1 eV) and stronger inter-chain interactions, favored by the structural planarity and increased linearity of the polymer backbone, as also supported by DFT calculations. The blend of PBDTFQ-TT and PC61BM ([6,6]-phenyl-C61-butyric acid methyl ester), compared to the PBDTFQ-T:PC61BM one processed under the same conditions (by blade-coating technique), showed greatly enhanced photovoltaic performance, with more than doubled power conversion efficiency (PCE up to 5.60% for the best device) due to the increased short-circuit current density and fill factor. However, similar PCEs were also achieved for PBDTFQ-T:PC61BM-based devices by optimizing the processing conditions through the addition of 1,8-diiodooctane (DIO) as the solvent additive. Through morphological and electrical analysis of the films, produced with and without additive, it was observed that the addition of DIO greatly enhances the self-organization, and consequently the charge mobility, of the thiophene π-bridge-based polymer, while it was detrimental for the nanoscale morphology and photovoltaic performances of the thieno[3,2-b]thiophene π-bridge-based polymer in the corresponding blend.

Enhanced Ultraviolet Stability of Air-Processed Polymer Solar Cells by Al Doping of the ZnO Interlayer.

Photostability of organic photovoltaic devices represents a key requirement for the commercialization of this technology. In this field, ZnO is one of the most attractive materials employed as an electron transport layer, and the investigation of its photostability is of particular interest. Indeed, oxygen is known to chemisorb on ZnO and can be released upon UV illumination. Therefore, a deep analysis of the UV/oxygen effects on working devices is relevant for the industrial production where the coating processes take place in air and oxygen/ZnO contact cannot be avoided. Here we investigate the light-soaking stability of inverted organic solar cells in which four different solution-processed ZnO-based nanoparticles were used as electron transport layers: (i) pristine ZnO, (ii) 0.03 at %, (iii) 0.37 at %, and (iv) 0.8 at % aluminum-doped AZO nanoparticles. The degradation of solar cells under prolonged illumination (40 h under 1 sun), in which the ZnO/AZO layers were processed in air or inert atmosphere, is studied. We demonstrate that the presence of oxygen during the ZnO/AZO processing is crucial for the photostability of the resulting solar cell. While devices based on undoped ZnO were particularly affected by degradation, we found that using AZO nanoparticles the losses in performance, due to the presence of oxygen, were partially or totally prevented depending on the Al doping level.

2D π-conjugated benzo[1,2-b:4,5-b′]dithiophene- and quinoxaline-based copolymers for photovoltaic applications

Two medium gap semiconducting polymers, P(1)-Q-BDT-4TR and P(2)-FQ-BDT-4TR, based on alternate units of alkyl-dithiophene substituted benzodithiophene (BDT) and quinoxaline units (without or with fluorine substitution), are synthesized and fully characterized. The polymers exhibit optical and electrical properties favorable for being employed as donors in BHJ OPV devices, such as: absorption spectra extending up to around 720 nm for a high solar spectrum coverage, deep lying HOMO energy levels for a high device open circuit voltage and LUMO energy levels higher than those of PC61BM and PC71BM for an efficient exciton dissociation. In particular, the presence of alkyl-dithiophene side chains allows us to obtain a high 2D π-conjugation which promotes red shifted absorption profiles, low HOMO energy levels (<−5.6 eV) and enhanced environmental and thermal stability. Moreover, the introduction of the fluorine atom in the polymer backbone allows us to obtain efficient OPV devices, based on as-cast P(2)-FQ-BDT-4TR:PC61BM blend, showing a JSC of −10.2 mA cm−2, VOC of 0.90 V, FF of 58% and PCE of 5.3%, without the need for any additional thermal treatment.

Black Polymers in Bulk-Heterojunction Solar Cells

The active materials in polymer solar cells have a decisive role on the performance of the cells. Polymers with extended absorption, i.e., black polymers with absorption covering the whole visible region are desired in order to capture the important parts of the solar irradiation. Different ways of achieving black active materials are discussed and two new alternating polyfluorene (APFO) copolymers with broad absorption, APFO-Black 1 and APFO-Black 2, using two different design strategies are described. The UV-Vis absorption spectra of the polymers extend to approximately 850 nm, and the polymers were used as donors and [6,6]phenyl-C61-butyric acid methyl ester (PCBM)[60] or PCBM[70] as acceptors in solar cell devices in various mixing ratios. The best combinations yielded an overall power conversion efficiency of 1.2% for APFO-Black 1 and 1.5% for APFO-Black 2.

Two-photon absorption of polyfluorene aggregates stabilized by insulin amyloid fibrils

We report on the photophysical and optical properties of a polyfluorene derivative (PFO) and its binding to the amyloid-forming protein insulin. The complexation is based on weak supramolecular interactions between amyloid fibrils and PFO in dissolved and aggregated forms. In particular, complexes of polyfluorene aggregates display sizeable two-photon absorption when stabilized by insulin fibril nanotemplates. We propose that a two-photon absorption enhancement mechanism is related to the combination of through-bond and through-space interactions of PFO. The findings reported here suggest that polyfluorene aggregates offer good nonlinear absorption properties and can be used as molecular markers for amyloid fibril recognition.

Synthesis and characterization of benzodithiophene and benzotriazole-based polymers for photovoltaic applications

Summary Two high bandgap benzodithiophene–benzotriazole-based polymers were synthesized via palladium-catalysed Stille coupling reaction. In order to compare the effect of the side chains on the opto-electronic and photovoltaic properties of the resulting polymers, the benzodithiophene monomers were substituted with either octylthienyl (PTzBDT-1) or dihexylthienyl (PTzBDT-2) as side groups, while the benzotriazole unit was maintained unaltered. The optical characterization, both in solution and thin-film, indicated that PTzBDT-1 has a red-shifted optical absorption compared to PTzBDT-2, likely due to a more planar conformation of the polymer backbone promoted by the lower content of alkyl side chains. The different aggregation in the solid state also affects the energetic properties of the polymers, resulting in a lower highest occupied molecular orbital (HOMO) for PTzBDT-1 with respect to PTzBDT-2. However, an unexpected behaviour is observed when the two polymers are used as a donor material, in combination with PC61BM as acceptor, in bulk heterojunction solar cells. Even though PTzBDT-1 showed favourable optical and electrochemical properties, the devices based on this polymer present a power conversion efficiency of 3.3%, considerably lower than the efficiency of 4.7% obtained for the analogous solar cells based on PTzBDT-2. The lower performance is presumably attributed to the limited solubility of the PTzBDT-1 in organic solvents resulting in enhanced aggregation and poor intermixing with the acceptor material in the active layer.

Correction to "a new tetracyclic lactam building block for thick, broad-bandgap photovoltaics".

Page 11579. Further analysis of the spectroscopic data of the NT monomer suggested that the majority product is the Oalkylated instead of N-alkylated product. The amide functionality displays ambident reactivity, and the ratio of Nor Oalkylation is governed by factors such as the employed halide on the alkyl reactant and the thermodynamic stability of the final product. For amide-containing structures employed in conjugated polymers, the N-alkylated product is usually the majority product. However, recently He et al. reported a new conjugated building block that favored O-alkylation over Nalkylation under reaction conditions similar to those we employed. To unambiguously determine which isomer was formed, we synthesized a crystalline C8-NT unit under conditions similar to those used for the initial 2-hexyldecyl-substituted NT unit. Analysis by single-crystal X-ray diffraction and comparison of the other spectroscopic data confirmed that the majority product after alkylation is O-alkylated. The correct structures of the NT unit and PTNT are depicted in Figure 1.