Diogo Pedrollo Lise

Microshear Bond Strength of Resin Cements to Lithium Disilicate Substrates as a Function of Surface Preparation.

OBJECTIVES To investigate the effect of hydrofluoric acid (HF) etching, silane solution, and adhesive system application on the microshear bond strength (μSBS) of lithium disilicate glass-ceramic (LD) to three resin cements. MATERIALS AND METHODS Circular bonding areas were delimited on the lithium disilicate surfaces using a perforated adhesive tape. Specimens were assigned to 18 subgroups (n=12) according to surface treatment: NT = no treatment; HF = 4.8% HF for 20 seconds; silane solution: (1) no silane; (2) Monobond Plus, a silane/10-methacryloyloxydecyl dihydrogen phosphate solution for 60 seconds; (3) Monobond Plus+ExciTE F DSC, a dual-cure adhesive; and resin cement: (1) Variolink II, a bisphenol A diglycidyl ether dimethacrylate (bis-GMA)-based, hand-mixed, dual-cure resin cement; (2) Multilink Automix, a bis-GMA-based, auto-mixed, dual-cure resin cement; (3) RelyX Unicem 2, a self-adhesive, auto-mixed, dual-cure resin cement. Tygon tubes (Ø=0.8 mm) were used as cylinder matrices for resin cement application. After 24 hours of water storage, the specimens were submitted to the μSBS test. Mode of failure was evaluated under an optical microscope and classified as adhesive, mixed, cohesive in resin cement, or cohesive in ceramic. Data were statistically analyzed with three-way analysis of variance and Dunnett test (p<0.05). RESULTS When means were pooled for the factor surface treatment, HF resulted in a significantly higher μSBS than did NT (p<0.0001). Regarding the use of a silane solution, the mean μSBS values obtained with Monobond Plus and Monobond Plus+ExciTE F DSC were not significantly different but were higher than those obtained with no silane (p<0.001). Considering the factor resin cement, Variolink II resulted in a significantly higher mean μSBS than did RelyX Unicem 2 (p<0.03). The mean μSBS for Multilink Automix was not significantly different from those of Variolink II and RelyX Unicem 2. According to Dunnett post hoc test (p<0.05), there was no significant difference in μSBS between the different resin cements for HF-etched and silanized (with or without adhesive application) LD surfaces. CONCLUSION LD may benefit from pretreatment of the inner surface with HF and silanization, regardless of the resin cement used.

Microtensile Bond Strength of Composite Cement to Novel CAD/CAM Materials as a Function of Surface Treatment and Aging

OBJECTIVES To evaluate the effect of different surface treatments on the bond strength to a composite and a polymer-infiltrated ceramic CAD/CAM block after six-month artificial aging. METHODS AND MATERIALS Two types of CAD/CAM blocks (Cerasmart, GC; Enamic, Vita Zahnfabrik) were cut in slabs of 4-mm thickness, divided into six groups, and subjected to the following surface treatments: group 1: no treatment; group 2: sandblasting (SB); group 3: SB + silane (Si); group 4: SB + Si + flowable composite (see below); group 5: 5% hydrofluoric acid etching (HF) + Si; and group 6: 37% phosphoric acid etching (H3PO4) + Si. Sections of the same group were luted together (n=3: 3 sandwich specimens/group) using a dual-cure self-adhesive cement for all groups, except for the sections of group 4 that were luted using a light-curing flowable composite. After three weeks of storage in 0.5% chloramine at 37°C, the sandwich specimens were sectioned in rectangular microspecimens and trimmed at the interface to a dumbbell shape (1.1-mm diameter). One half of the specimens was subjected to a microtensile bond strength (μTBS) test, and the other half was tested after six months of water storage (aging). Data were statistically analyzed with a linear mixed-effects model for the factors surface treatment, material type, and aging, together with their first-degree interactions (α=0.05). RESULTS The lowest bond strengths were obtained in the absence of any surface treatment (group 1), while the highest μTBSs were obtained when the surface was roughened by either SB or HF, this in combination with chemical adhesion through Si. Loss in bond strength was observed after six-month aging when either surface roughening or silanization, or both, were omitted. CONCLUSIONS Both the composite and polymer-infiltrated ceramic CAD/CAM blocks appeared equally bonding-receptive regardless of the surface treatment used. Creating a microretentive surface by either SB or HF, followed by chemical adhesion using Si, is mandatory to maintain the bond strength after six months.

Tooth Fragment Reattachment: The Natural Restoration

The aim of this manuscript was to discuss some important considerations about tooth fragment reattachment and report the success of a clinical case in which a tooth fragment and direct composite resin were used to restore a fractured anterior tooth. Clinical and radiographic examination 12 months after trauma showed good esthetics and periodontal health.

Strain development in bulk-filled cavities of different depths characterized using a non-destructive acoustic emission approach

OBJECTIVES (1) To evaluate the effect of cavity depth and composite type on the interfacial debonding in bulk-filled cavities. (2) To correlate the theoretical shrinkage stress and the level of interfacial debonding determined by acoustic emission (AE). METHODS 80 sound molars were divided in two groups to receive a Class-I cavity (3.5×3.5mm) with 2.5- or 4.0-mm depth. The cavities were restored with either a conventional paste-like (Filtek Z100, 3M ESPE), a conventional flowable (G-ænial Universal Flo, GC), a bulk-fill paste-like (Tetric EvoCeram Bulk Fill, Ivoclar Vivadent) or a bulk-fill flowable (SDR, Dentsply) composite (n=10). AE signals were recorded from the start of curing for 20min. The cumulative number of AE events was correlated with the theoretical maximum shrinkage stress induced by each composite. Two samples from each group were scanned using micro-computed tomography (μCT) and qualitatively evaluated. RESULTS Both composite type and cavity depth had a significant influence on the number of AE. The conventional paste-like composite generated significantly more AE than the other composites. The AE number increased sigmoidally in function of time, with a more rapid increase after a few seconds for the conventional composites than for the bulk-fill composites. A strong linear correlation was found between the predicted shrinkage stress values and the total number of AE events for both cavities depth. Representative μCT images showed larger de-bonding areas for 4.0-mm cavities and for conventional composites. SIGNIFICANCE Premature interfacial or cohesive cracks can already develop during placement/curing of the composite. This might compromise the restoration integrity and in turn affect its survival in the long term. The amount AE events increased linearly with the theoretical maximum shrinkage stress of the composites.

Esthetic Rehabilitation of Retained Primary Teeth—A Conservative Approach

With the advancement in ceramic restorations bonded to tooth structure, the treatment has become a feasible and conservative option to restore teeth with alteration in shape when owing to high demand in esthetics, with or without minimum tooth preparation. This article describes a report of a 32-year-old woman who was dissatisfied with her smile. The patient reported that she still had deciduous teeth, and that the maxillary lateral incisors had been restored with direct resin composite to correct the teeth shape. After discussing the restorative possibilities, a decision was made to place all-ceramic crowns (lithium disilicate glass-ceramic) with minimal tooth preparation, which figures as a conservative full-coverage approach. An esthetic outcome resembling a natural-looking smile resulted in the patients satisfaction. Bonding of all-ceramic crowns onto minimally prepared deciduous teeth figures as a conservative treatment in case of partial anodontia, which decreases the chance of root resorption induced by trauma and benefits from good adhesion to enamel.

Bleaching Options for Pulp-Calcified Teeth: Case History Reports

The aim of this article is to review some essential aspects of anterior tooth calcification and its esthetic treatment. Furthermore, three cases including different and successful bleaching strategies are reported.