Domenico Giannone

High efficiency silicon nitride surface grating couplers

High efficiency surface grating couplers for silicon nitride waveguides have been designed, fabricated, and characterized. Coupling efficiencies exceeding 60 % are reported at a wavelength of 1.31 mum, as well as angular and wavelength -3 dB tolerances of 4 degrees and 50 nm, respectively. When the wavelength is increased from 1310 nm to 1450 nm the coupling efficiency progressively decreases but remains above 20 % at 1450 nm. The influence of the duty ratio of the grating has also been investigated: maximum coupling efficiency was obtained at 50 % duty ratio.

Highly Integrated Optical 4

In this paper, we present the design, fabrication, and characterization of a highly integrated optical 4 x 4 crossbar based on microring resonator add-drop filters. The designed crossbar structure, as small as 50 mum x 50 mum, has been fabricated in CMOS compatible silicon on insulator technology. Finally, experimental results proving the proper operation of the fabricated crossbar structures are discussed.

\,\times\,

We report a PM all-normal, all-in-fiber passively mode-locked laser operating at 1030 nm. The main pulse shaping mechanism is provided by a tilted chirped-FBG. The laser delivers nanojoule range highly chirped pulses at a repetition rate of about 40 MHz. The FWHM of the optical spectrum is up to 7.8 nm leading to sub-500 fs compressed optical pulses. The influence of the filtering bandwidth and the output coupling ratio has been investigated.

4 Crossbar in Silicon-on-Insulator Technology

We present an efficient and highly alignment-tolerant light coupling and distribution system for a multichannel Si3N4/SiO2 single-mode photonics sensing chip. The design of the input and output couplers and the distribution splitters is discussed. Examples of multichannel data obtained with the system are given.

All-normal dispersion, all-fibered PM laser mode-locked by SESAM

We present an overview of the 4MOST project at the Preliminary Design Review. 4MOST is a major new wide-field, high-multiplex spectroscopic survey facility under development for the VISTA telescope of ESO. 4MOST has a broad range of science goals ranging from Galactic Archaeology and stellar physics to the high-energy physics, galaxy evolution, and cosmology. Starting in 2021, 4MOST will deploy 2436 fibres in a 4.1 square degree field-of-view using a positioner based on the tilting spine principle. The fibres will feed one high-resolution (R~20,000) and two medium resolution (R~5000) spectrographs with fixed 3-channel designs and identical 6k x 6k CCD detectors. 4MOST will have a unique operations concept in which 5-year public surveys from both the consortium and the ESO community will be combined and observed in parallel during each exposure. The 4MOST Facility Simulator (4FS) was developed to demonstrate the feasibility of this observing concept, showing that we can expect to observe more than 25 million objects in each 5-year survey period and will eventually be used to plan and conduct the actual survey.

Light coupling and distribution for Si3N4∕SiO2 integrated multichannel single-mode sensing system

We present a new type of multicore fiber (MCF) and photonic lantern that consists of 511 individual cores designed to operate over a broadband visible wavelength range (380-860nm). It combines the coupling efficiency of a multimode fiber with modal stability intrinsic to a single mode fibre. It is designed to provide phase and amplitude scrambling to achieve a stable near field and far field illumination pattern during input coupling variations; it also has low modal noise for increased photometric stability. Preliminary results are presented for the new MCF as well as current state of the art octagonal fiber for comparison.

4MOST: the 4-metre Multi-Object Spectroscopic Telescope project at preliminary design review

The experimental demonstration of a high efficiency silicon nitride grating coupler is reported for wavelengths from lambda = 1.25 to 1.45 mum for TE polarization. At the resonant angle, a coupling efficiency higher than 60% has been measured.

New multicore low mode noise scrambling fiber for applications in high-resolution spectroscopy

In this work, we report advances in the fabrication and anticipated performance of a polymer biosensor photonic chip developed in the European Union project P3SENS (FP7-ICT4-248304). Due to the low cost requirements of point-ofcare applications, the photonic chip is fabricated from nanocomposite polymeric materials, using highly scalable nanoimprint- lithography (NIL). A suitable microfluidic structure transporting the analyte solutions to the sensor area is also fabricated in polymer and adequately bonded to the photonic chip. We first discuss the design and the simulated performance of a high-Q resonant cavity photonic crystal sensor made of a high refractive index polyimide core waveguide on a low index polymer cladding. We then report the advances in doped and undoped polymer thin film processing and characterization for fabricating the photonic sensor chip. Finally the development of the microfluidic chip is presented in details, including the characterisation of the fluidic behaviour, the technological and material aspects of the 3D polymer structuring and the stable adhesion strategies for bonding the fluidic and the photonic chips, with regards to the constraints imposed by the bioreceptors supposedly already present on the sensors.

A high efficiency silicon nitride grating coupler

We present the most recent results of EU funded project P3SENS (FP7-ICT-2009.3.8) aimed at the development of a low-cost and medium sensitivity polymer based photonic biosensor for point of care applications in proteomics. The fabrication of the polymer photonic chip (biosensor) using thermal nanoimprint lithography (NIL) is described. This technique offers the potential for very large production at reduced cost. However several technical challenges arise due to the properties of the used materials. We believe that, once the NIL technique has been optimised to the specific materials, it could be even transferred to a kind of roll-to-roll production for manufacturing a very large number of photonic devices at reduced cost.

Design and process development of a photonic crystal polymer biosensor for point-of-care diagnostics

We present a compact passive optical add-drop filter which incorporates two microring resonators and a waveguide intersection in silicon-on-insulator (SOI) technology. Such a filter is a key element for designing simple layouts of highly integrated complex optical networks-on-chip. The filter occupies an area smaller than 10μm×10μm and exhibits relatively high quality factors (up to 4000) and efficient signal dropping capabilities. In the present work, the influence of filter parameters such as the microring-resonators radii and the coupling section shape are analyzed theoretically and experimentally