Donncha Haverty

Kinetics of levulinic acid and furfural production from Miscanthus × giganteus

This study investigated the kinetics of acid hydrolysis of the cellulose and hemicellulose in Miscanthus to produce levulinic acid and furfural under mild temperature and high acid concentration. Experiments were carried out in an 8L-batch reactor with 9%-wt. biomass loading, acid concentrations between 0.10 and 0.53 M H2SO4, and at temperatures between 150 and 200°C. The concentrations of xylose, glucose, furfural, 5-hydroxymethylfurfural and levulinic acid were used in two mechanistic kinetic models for the prediction of the performance of ideal continuous reactors for the optimisation of levulinic acid and the concurrent production of furfural. A two-stage arrangement was found to maximise furfural in the first reactor (PFR - 185°C, 0.5M H2SO4, 27.3%-mol). A second stage leads to levulinic acid yields between 58% and 72%-mol at temperatures between 160 and 200°C.

Structural Order and Dielectric Behaviour of Hydroxyapatite

Disorder of the OH− ion orientation is inherent in the currently accepted structure of hydroxyapatite (HA), hexagonal P63/m. In the case of local ordering in the OH− ion orientation, the resulting structure will be a monoclinic P21/b, with an alternate orientation of OH− columns in the b-direction. Both of these proposed structures are electrically non polar and fail to explain the polarisation phenomena observed in HA. Here we report some theoretical considerations of structural order in HA and show that in addition to the non polar P21/b phase HA can also exist as a polar phase. Various physical properties including static dielectric constant and polarisation are simulated from empirical interatomic potential calculations and used to explain the observed dielectric anomaly in sintered hydroxyapatite.

Direct and ultrasonic measurements of macroscopic piezoelectricity in sintered hydroxyapatite

Macroscopic piezoelectricity in hydroxyapatite (HA) ceramic was measured by a direct quasistatic method and an ultrasonic interference technique. The effective symmetry of polycrystalline aggregate was established and a detailed theoretical analysis was carried out to determine by these two methods the shear piezoelectric coefficient, d14, of HA. Piezoelectric nature of HA was proved qualitatively although a specific quantitative value for the d14 coefficient could not be established. Ultrasound method was also employed to anisotropic elastic constants, which agreed well with those measured from the first principles.

Pyroelectric surface charge in hydroxyapatite ceramics

Surface charge of pyroelectric nature is measured in poled hydroxyapatite ceramics. The average pyroelectric constant can range from 0.1 to 40 nC cm−2 K−1 at temperatures of 300–500 °C, while at 27–60 °C the value ranges from 15 to 64 nC cm−2 K−1. The higher temperature values are comparable to conventional pyroelectric ceramics such as LiTaO3 or PZT. The lower temperature values are four orders higher than those observed in bone and tendon.

Autothermal, single-stage, performic acid pretreatment of Miscanthus x giganteus for the rapid fractionation of its biomass components into a lignin/hemicellulose-rich liquor and a cellulase-digestible pulp

A novel approach to the performic acid pulping of biomass enables effective delignification and fractionation in a time frame not achieved heretofore. An autothermal decomposition reaction was triggered when 100mg/L Fe(2)(SO(4))(3) in 4.0 M NaOH was added to 5% or 7.5% H(2)O(2) in aqueous formic acid containing chipped Miscanthus x giganteus. Peroxy-decomposition resulted in pressures of 19 and 35 bar in the 5% and 7.5% peroxide liquors and reduced the lignin content in the resulting pulps to <6% within 140 and 30 min, respectively. Solubilised lignin was available for recovery from the liquor by subsequent dilution with water. Hemicellulose removal to the liquor was 68% and 89% for the 5% and 7.5% peroxide solutions. Crystalline cellulose yields were >99% and >95% and the rate of glucose release from cellulase digestion of the pulps in 24h was more than 20-fold that for the raw Miscanthus.

The effect of hydrogen peroxide concentration and solid loading on the fractionation of biomass in formic acid.

This study investigated the fractionation of biomass using a decomposing mixture of hydrogen peroxide-formic acid as a pretreatment for the biorefining of Miscanthus × giganteus and of sugarcane bagasse. The main parameters investigated were the hydrogen peroxide concentration (2.5, 5.0 and 7.5 wt%) and biomass loading (5.0 and 10.0 wt%). At the highest hydrogen peroxide concentration used (7.5 wt%), the energy released by the decomposition of the H2O2 could heat the reaction mixture up to 180 °C in a short time (6-16 min). As a result, highly delignified pulps, with lignin removal as high as 92 wt%, were obtained. This delignification process also solubilised a significant amount of pentosan (82-98 wt%) from the initial biomass feedstock, and the resulting pulp had a high cellulosic content (92 wt%). The biomass loading only affected the reaction rate of hydrogen peroxide decomposition. Various analytical methods, including Fourier transform infrared spectroscopy, and thermogravimetric and elemental analyses, characterized the lignin obtained.