Duangjai Nacapricha

Pervaporation-flow injection with chemiluminescence detection for determination of iodide in multivitamin tablets

This paper describes the use of a pervaporation (PV) technique in a flow injection (FI) system for selective improvement in iodide analysis. Iodide in the sample zone is oxidized to iodine, which permeates through a hydrophobic membrane. Detection of the diffused iodine is achieved using the chemiluminescent (CL) emission at 425nm that results from the reaction between iodine and luminol. The method was applied for the analysis of some pharmaceutical products, such as nuclear emergency tablets and multivitamin tablets. Ascorbic acid present in multivitamin samples interfered seriously with the analysis, and off-line sample treatment using anion exchange resin was employed to successfully remove ascorbic acid before the analysis. Ascorbic acid was flushed from the column using 0.4M sodium nitrate followed by elution of iodide with 2M sodium nitrate. The detection limit (3S.D.) of the system was 0.5mgl(-1), with reproducibility of 5.2% R.S.D. at 5mgl(-1). Sample throughput was determined as 30injectionsh(-1). There was good agreement between iodide concentrations from extracted samples determined using four different methods, i.e., PV-FI, gas diffusion-flow injection, potentiometry and ICP-MS. A comparison of the analytical features of the developed pervaporation system with these of the previously reported chemiluminescence gas diffusion-flow injection previously reported is also described.

Sequential extraction of phosphorus in soil and sediment using a continuous-flow system

Distribution and mobility of phosphorus in soil and sediment are usually studied by sequential extraction. In the extraction procedure, a sample is treated with a series of reagents to distinguish the phases to which phosphorus is associated such as carbonate and iron or manganese oxides, etc. There have been a number of extraction schemes presented for phosphorus. At present, all of the existing schemes are carried out batchwise. Phosphorus contents derived from all sequences are operationally defined and depend on experimental conditions. An extraction procedure, which is a continuous-flow-based technique, was recently proposed by our group for metals in soils and sediments. The extraction is carried out in a closed chamber through which extractants are passed sequentially. In this paper, the system was investigated using the extraction scheme of Hieltjes and Lijklema to study distribution of phosphorus in three certified reference materials (CRMs). A number of fractions were collected for each reagent for subsequent colorimetric determination. The results are compared with those obtained from a batch extraction. The summation of phosphorus contents of all phases were compared with the certified values and with the values obtained from total digestion. These results have demonstrated that the continuous extraction system developed is also applicable for fractionation of phosphorus. Advantage and disadvantage are discussed.

Simple flow injection for determination of sulfite by amperometric detection using glassy carbon electrode modified with carbon nanotubes-PDDA-gold nanoparticles.

A new approach is presented for sensitive and selective measurement of sulfite (SO3(2-)) in beverages based on a simple flow injection system with amperometric detection. In this work, the sulfite sensor was a glassy carbon electrode modified with multiwall carbon nanotubes-poly(diallyldimethylammonium chloride)-gold nanoparticles composites (CNTs-PDDA-AuNPs/GC). Electrochemical oxidation of sulfite with this electrode was first studied in 0.1M phosphate buffer (pH 7.0) using cyclic voltammetry. The results indicated that the CNTs-PDDA-AuNPs/GC electrode possesses electrocatalytic activity for the oxidation of sulfite with high sensitivity and selectivity. Sulfite was quantified using amperometric measurement with the new sensor at +0.4V vs Ag/AgCl in conjunction with flow injection. The linear working range for the quantitation of sulfite was 2-200 mg L(-1) (r(2)=0.998) with a detection limit of 0.03 mg L(-1) (3σ of blank) and an estimated precision of 1.5%.The proposed method was successfully applied to the determination of sulfite in fruit juices and wines with a sample throughput of 23 samples per hour.

Enantiomeric separation of some common controlled stimulants by capillary electrophoresis with contactless conductivity detection

CE methods with capacitively coupled contactless conductivity detection (C4D) were developed for the enantiomeric separation of the following stimulants: amphetamine (AP), methamphetamine (MA), ephedrine (EP), pseudoephedrine (PE), norephedrine (NE) and norpseudoephedrine (NPE). Acetic acid (pH 2.5 and 2.8) was found to be the optimal background electrolyte for the CE‐C4D system. The chiral selectors, carboxymethyl‐β‐cyclodextrin (CMBCD), heptakis(2,6‐di‐O‐methyl)‐β‐cyclodextrin (DMBCD) and chiral crown ether (+)‐(18‐crown‐6)‐2,3,11,12‐tetracarboxylic acid (18C6H4), were investigated for their enantioseparation properties in the BGE. The use of either a single or a combination of two chiral selectors was chosen to obtain optimal condition of enantiomeric selectivity. Enantiomeric separation of AP and MA was achieved using the single chiral selector CMBCD and (hydroxypropyl)methyl cellulose (HPMC) as the modifier. A combination of the two chiral selectors, CMBCD and DMBCD and HPMC as the modifier, was required for enantiomeric separation of EP and PE. In addition, a combination of DMBCD and 18C6H4 was successfully applied for the enantiomeric separation of NE and NPE. The detection limits of the enantiomers were found to be in the range of 2.3–5.7 μmol/L. Good precisions of migration time and peak area were obtained. The developed CE‐C4D method was successfully applied to urine samples of athletes for the identification of enantiomers of the detected stimulants.

A reagent-free SIA module for monitoring of sugar, color and dissolved CO2 content in soft drinks.

This work presents a new sequential injection analysis (SIA) method and a module for simultaneous and real-time monitoring of three key parameters for the beverage industry, i.e., the sugar content (measured in Brix), color and dissolved CO(2). Detection of the light reflection at the liquid interface (the schlieren effect) of sucrose and water was utilized for sucrose content measurement. A near infrared LED (890+/-40 nm) was chosen as the light source to ensure that all the ingredients and dyes in soft drinks will not interfere by contributing light absorption. A linear calibration was obtained for sucrose over a wide concentration range (3.1-46.5 Brix). The same module can be used to monitor the color of the soft drink as well as the dissolved CO(2) during production. For measuring the color, the sample is segmented between air plugs to avoid dispersion. An RGB-LED was chosen as the light source in order to make this module applicable to a wide range of colored samples. The module also has a section where dissolved CO(2) is measured via vaporization of the gas from the liquid phase. Dissolved CO(2), in a flowing acceptor stream of water resulting in the change of the acceptor conductivity, is detected using an in-house capacitively coupled contactless conductivity detector (C(4)D). The module includes a vaporization unit that is also used to degas the carbonated drink, prior the measurements of sucrose and color within the same system. The method requires no chemicals and is therefore completely friendly to the environment.

Flow-injection determination of iodide ion in nuclear emergency tablets, using boron-doped diamond thin film electrode.

The electrochemical determination of iodide was studied at boron-doped diamond thin film electrodes (BDD) using cyclic voltammetry (CV) and flow-injection (FI) analysis, with amperometric detection. Cyclic voltammetry of iodide was conducted in a phosphate buffer pH 5. Experiments were performed using glassy carbon (GC) electrode as a comparison. Well-defined oxidation waves of the quasi-reversible cyclic voltammograms were observed at both electrodes. Voltammetric signal-to-background ratios (S/B) were comparable. However, the GC electrode gives much greater in the background current as usual. The potential sweep rate dependence exhibited that the peak current of iodide oxidation at 1mM varied linearly (r(2) = 0.998) with the square root of the scan rate, from 0.01 to 0.30Vs(-1). This result indicates that the reaction is a diffusion-controlled process with negligible adsorption on BDD surface, at this iodide concentration. Results of the flow-injection analysis show a highly reproducible amperometric response. The linear working range was observed up to 200muM (r(2) = 0.999). The detection limit, as low as 0.01muM (3sigma of blank), was obtained. This method was successfully applied for quantification of iodide contents in nuclear emergency tablets.

Simple flow injection system for colorimetric determination of iodate in iodized salt

This work presents a flow injection (FI) system that was developed for determination of iodate. The system utilizes the oxidation of iodide by the analyte to iodine, which subsequently forms tri-iodide. In the presence of starch, the blue I(3)(-)-starch complex is developed within the sample zone and can be colorimetrically detected at 590 nm. Optimization was carried out to make the system suitable for quantitating iodate added to table salts. To prevent accumulation of the blue complex residue on walls of tubing and the flow cell, a port was placed in the system for injection of 10(-3) M thiosulfate plug (100 mul). An injection of this cleaning solution after each sample injection is recommended to avoid positive baseline shift. By means of the paired t-test, the amounts of iodine (mg I kg(-1)) were statistically compared with the results determined by titration and by iodide ion selective electrode. No significant disagreement at 95% confidence was observed. The proposed system is very simple, uses common chemicals and provides rapid analysis (65 injections per h) with high precision (R.S.D.=0.66%, n=10). A detection limit of 2 mg I kg(-1) salt can be achieved.

RADIOMETRIC DETECTORS FOR FLOW-INJECTION ANALYSIS

Abstract Four types of radiometric cell were constructed and applied in flow-injection analysis. The cells were designed for use with end-window and liquid-type GM counters and with cylindrical and well-type scintillation [NaI(Tl)] counters. The performance of the cells was compared with that of a spectrophotometric flow-through cell by injecting a radioactive solution and a coloured solution, respectively, under otherwise similar conditions, and measuring the dispersion.

Separation of α‐, β‐, γ‐, δ‐tocopherols and α‐tocopherol acetate on a pentaerythritol diacrylate monostearate‐ethylene dimethacrylate monolith by capillary electrochromatography

This work reports the first use of a monolith with method development for the separation of tocopherol (TOH) compounds by CEC with UV detection. A pentaerythritol diacrylate monostearate‐ethylene dimethacrylate (PEDAS‐EDMA) monolithic column has been investigated for an optimised condition to separate α‐, β‐, γ‐ and δ‐TOHs, and α‐tocopherol acetate (TAc). The PEDAS‐EDMA monolith showed a remarkably good selectivity for separation of the TOH isomers including the β‐ and γ‐isomers which are not easily separated by standard C8 or C18 particle‐packed columns. Retention studies indicated that an RP mechanism was involved in the separation on the PEDAS‐EDMA column, but polar interactions with the underlying ester and hydroxyl groups enhanced the separation of the problematic β‐ and γ‐isomers. Separation of all the compounds was achieved within 25 min using 3:10:87 v/v/v 100 mM Tris buffer (pH 9.3)/methanol/ACN as the mobile phase. The method was successfully applied to a pharmaceutical sample with recoveries from 93 to 99%. Intraday and interday precisions (%RSD) for peak area and retention time were less than 2.3. LODs for all four TOHs and TAc were below 1 ppm.

AAO-CNTs electrode on microfluidic flow injection system for rapid iodide sensing

In this work, carbon nanotubes (CNTs) nanoarrays in anodized aluminum oxide (AAO-CNTs) nanopore is integrated on a microfluidic flow injection system for in-channel electrochemical detection of iodide. The device was fabricated from PDMS (polydimethylsiloxane) microchannel bonded on glass substrates that contains three-electrode electrochemical system, including AAO-CNTs as a working electrode, silver as a reference electrode and platinum as an auxiliary electrode. Aluminum, stainless steel catalyst, silver and platinum layers were sputtered on the glass substrate through shadow masks. Aluminum layer was then anodized by two-step anodization process to form nanopore template. CNTs were then grown in AAO template by thermal chemical vapor deposition. The amperometric detection of iodide was performed in 500-μm-wide and 100-μm-deep microchannels on the microfluidic chip. The influences of flow rate, injection volume and detection potential on the current response were optimized. From experimental results, AAO-CNTs electrode on chip offers higher sensitivity and wider dynamic range than CNTs electrode with no AAO template.