Dustin Moon

Electrophoresis of a Charged Droplet in a Dielectric Liquid for Droplet Actuation

Electrophoretic motion of a charged droplet in a dielectric fluid under an electric field has been investigated experimentally for use as a microdroplet actuation method. The effects of the droplet size, electric field strength, and electrolyte concentration and ion species on the charging of an aqueous droplet have been examined. The amount of electrical charging has been measured by two different methods: indirect measurement using the image analysis of droplet motion and direct measurement using the electrometer. Quantitative comparison of the droplet charge measured experimentally and the theoretical value of a perfectly conductive sphere shows that an aqueous droplet is less charged than the corresponding perfectly conductive sphere. The limiting effect on electrical charging is more significant for an electrolyte droplet, and the effect is positively correlated to the electrolyte concentration rather than the ion species. This implies that the low electrical conductivity of water is not a major cause of the limiting effect. The scaling law of the charging amount for a deionized water droplet nearly follows that of the perfect conductor, whereas for an electrolyte droplet, the scaling law exponent is slightly higher. Some advantages and potentials of the current droplet actuation method are also discussed in comparison with the conventional ones.

Discrete electrostatic charge transfer by the electrophoresis of a charged droplet in a dielectric liquid.

We have experimentally investigated the electrostatic charging of a water droplet on an electrified electrode surface to explain the detailed inductive charging processes and use them for the detection of droplet position in a lab-on-a-chip system. The periodic bouncing motion of a droplet between two planar electrodes has been examined by using a high-resolution electrometer and an image analysis method. We have found that this charging process consists of three steps. The first step is inductive charge accumulation on the opposite electrode by the charge of a droplet. This induction process occurs while the droplet approaches the electrode, and it produces an induction current signal at the electrometer. The second step is the discharging of the droplet by the accumulated induced charge at the moment of contact. For this second step, there is no charge-transfer detection at the electrometer. The third step is the charging of the neutralized droplet to a certain charged state while the droplet is in contact with the electrode. The charge transfer of the third step is detected as the pulse-type signal of an electrometer. The second and third steps occur simultaneously and rapidly. We have found that the induction current by the movement of a charged droplet can be accurately used to measure the charge of the droplet and can also be used to monitor the position of a droplet under actuation. The implications of the current findings for understanding and measuring the charging process are discussed.

Digital Electrophoresis of Charged Droplets

A digital microfluidic system based on a direct electric charging and subsequent electrophoretic manipulation of droplets is made by simple fabrication at low cost. Digitally controlled two-dimensional droplet motions are realized by digital polarity control of an array of electrodes. By independent control of droplets and colorimetric detection, the coalescence and mixing of droplets is analyzed quantitatively. The gelation of sodium alginate and the crystallization of calcium carbonate by multiple droplet translations and coalescence and the actuation of glassy carbon beads are demonstrated to show the versatile manipulation capability of the proposed technology. Finally, we discuss the implications and potentials of the present technology.

Interfacial tension of complex coacervated mussel adhesive protein according to the Hofmeister series.

Complex coacervation is a liquid-liquid phase separation in a colloidal system of two oppositely charged polyelectrolytes or colloids. The interfacial tension of the coacervate phase is the key parameter for micelle formation and interactions with the encapsulating material. However, the relationship between interfacial tensions and various salt solutions is poorly understood in complex coacervation. In the present work, the complex coacervate dynamics of recombinant mussel adhesive protein (MAP) with hyaluronic acid (HA) were determined in the presence of Hofmeister series salt ions. Using measurements of absorbance, hydrodynamic diameter, capillary force, and receding contact angle in the bulk phase, the interfacial tensions of complex coacervated MAP/HA were determined to be 0.236, 0.256, and 0.287 mN/m in 250 mM NaHCOO, NaCl, and NaNO3 solutions, respectively. The sequences of interfacial tensions and contact angles of the complex coacervates in the presence of three sodium salts with different anions were found to follow the Hofmeister ordering. The tendency of interfacial tension between the coacervate and dilute phases in the presence of different types of Hofmeister salt ions could provide a better understanding of Hofmeister effects on complex coacervated materials based on the protein-polysaccharide system. This information can also be utilized for microencapsulation and adsorption by controlling intramolecular interactions. In addition, the injection molding dynamics of mussel byssus formation was potentially explained based on the measured interfacial tension of coacervated MAP.

Pumpless dispensing of a droplet by breaking up a liquid bridge formed by electric induction.

Dispensing uniform pico‐to‐nanoliter droplets has become one of essential components in various application fields from high‐throughput bio‐analysis to printing. In this study, a new method is suggested and demonstrated for dispensing a droplet on the top plate with an inverted geometry by using electric field. The process of dispensing droplets consists of two stages: (i) formation of liquid bridge by moving up the charged fluid mass using the electrostatic force between the charges on the fluid mass and the induced charges on the substrate and (ii) its break‐up by the motion of the top plate. Different from conventional electrohydrodynamic methods, electric induction enables the droplets to be dispensed on various surfaces including non‐conducting substrate. The use of capillarity with an inverted geometry removes the need of external pumps or elaborates control for constant flow feed. The droplet diameter has been characterized as a function of the nozzle‐to‐plate distance and the plate moving velocity. The robustness of the present method is shown in terms of nozzle length and applied voltage. Finally, its practical applicability is confirmed by rendering a 19 by 24 array of highly uniform droplets with only 1.8% size variation without use of any active feedback control.

Pico Liter Dispensing Using Liquid Bridge Breakup in Immiscible Fluid

A simple and robust way is devised to generate picoliter droplets out of a single microliter drop for the use of generating monodisperse droplets in droplet-based microfluidics. A single aqueous drop is placed between two glass substrates and immersed in silicone oil, to form a liquid bridge. Then one substrate is moved with a constant velocity ranging from 50 to 1000 μm/s. As the distance between two glass plates increases, the liquid bridge breaks up and smaller droplets or satellites are formed. It is found that, for the case of fixed outer fluid, the droplets of nearly the same size are generated over several orders of moving velocity. However, the size of a satellite droplet increases as the mother drop size increases, and it decreases as the outer fluid viscosity increases. Based on this result, a picoliter-droplet was successfully dispensed repeatedly for 100 times within 2% relative standard deviation, on-demand. To confirm its feasibility of single particle encapsulation, a single polystyrene microparticle has been captured successfully using this method without complex control.