E. Casero

Gold nanoparticles-induced enhancement of the analytical response of an electrochemical biosensor based on an organic-inorganic hybrid composite material

The design and characterization of a new organic-inorganic hybrid composite material for glucose electrochemical sensing are described. This material is based on the entrapment of both gold nanoparticles (AuNPs) and glucose oxidase, which was chosen as a model, into a sol-gel matrix. The addition of spectroscopic grade graphite to this system, which confers conductivity, leads to the development of a material particularly attractive for electrochemical biosensor fabrication. The characterization of the hybrid composite material was performed using atomic force microscopy and scanning electron microscopy techniques. This composite material was applied to the determination of glucose in presence of hydroxymethylferrocene as a redox mediator. The system exhibits a clear electrocatalytic activity towards glucose, allowing its determination at 250 mV vs Ag/AgCl. The performance of the resulting enzyme biosensor was evaluated in terms of sensitivity, detection limit, linear response range, stability and accuracy. Finally, the enhancement of the analytical response of the resulting biosensor induced by the presence of gold nanoparticles was evaluated by comparison with a similar organic-inorganic hybrid composite material without AuNPs.

Diamond nanoparticles based biosensors for efficient glucose and lactate determination

In this work, we report the modification of a gold electrode with undoped diamond nanoparticles (DNPs) and its applicability to the fabrication of electrochemical biosensing platforms. DNPs were immobilized onto a gold electrode by direct adsorption and the electrochemical behavior of the resulting DNPs/Au platform was studied. Four well-defined peaks were observed corresponding to the DNPs oxidation/reduction at the underlying gold electrode, which demonstrate that, although undoped DNPs have an insulating character, they show electrochemical activity as a consequence of the presence of different functionalities with unsaturated bonding on their surface. In order to develop a DNPs-based biosensing platform, we have selected glucose oxidase (GOx), as a model enzyme. We have performed an exhaustive study of the different steps involved in the biosensing platform preparation (DNPs/Au and GOx/DNPs/Au systems) by atomic force microscopy (AFM), field emission scanning electron microscopy (FE-SEM) and cyclic voltammetry (CV). The glucose biosensor shows a good electrocatalytic response in the presence of (hydroxymethyl)ferrocene as redox mediator. Once the suitability of the prototype system to determine glucose was verified, in a second step, we prepared a similar biosensor, but employing the enzyme lactate oxidase (LOx/DNPs/Au). As far as we know, this is the first electrochemical biosensor for lactate determination that includes DNPs as nanomaterial. A linear concentration range from 0.05 mM to 0.7 mM, a sensitivity of 4.0 µA mM(-1) and a detection limit of 15 µM were obtained.

Modified electrode approaches for nitric oxide sensing

Three different methods for the determination of nitric oxide (NO) in solution are described. These are based, respectively, on the use of a horseradish peroxidase (HRP) biosensor or on electrodes modified with films of redox-active transition metal complexes. In the case of the biosensor the enzyme was electrochemically immobilized onto a glassy carbon (GC) electrode. The activity of HRP is inhibited in presence of NO. Thus, the decrease in activity is correlated to the concentration of NO present in solution. The biosensor responds linearly over the range of 2.7x10(-6)-1.1x10(-5) M NO with a detection limit (5% inhibition) of 2.0x10(-6) M. In the case of chemically modified electrodes, particular emphasis is placed on materials capable of catalyzing the oxidation of NO. In terms of electrocatalyst, the discussion will centre on electrodeposited films of 6,17-diferrocenyldibenzo[b,i]5,9,14,18-tetraaza[14]annulen]-nickel(II) and indium(III) hexacyanoferrate(III). The resulting sensors exhibited potent and persistent electroacatalytic activity towards the oxidation of NO with low detection limits (1 muM) and good linear relationship between the catalytic current and NO concentrations. In addition, interference due to the presence of nitrate and nitrite have been significantly reduced. According to these results, the described modified electrodes have been used as sensors for the determination of NO generated by decomposition of a typical NO-donor, such as S-nitroso-N-acetyl-d,l-penicillamine (SNAP). A critical comparison of the various methodologies employed is made.

Electrocatalytic Oxidation of Nitric Oxide at 6,17‐Diferrocenyl‐dibenzo[b,i]5,9,14,18‐tetraaza[14]annulen]‐nickel(II) Modifed Electrodes

The preparation and electrochemical characterization of glassy carbon, gold or carbon paste electrodes modified with 6,17-Diferrocenyl-dibenzo[b,i]5,9,14,18-tetraaza[14]annulen]-nickel(II) as well as their behavior as electrocatalysts toward the oxidation of nitric oxide is described. These modified electrodes were used for the development of amperometric sensors for the determination of nitric oxide in solution. The sensors were prepared by electrochemical deposition of the mentioned material on glassy carbon or gold electrodes or including it in a carbon paste electrode. The resulting sensors exhibited potent and persistent electrocatalytic activity towards the oxidation of nitric oxide with low detection limits (1 μM) and good linear relationship between the current and nitric oxide concentration.

Dual-Stage DNA Sensing: Recognition and Detection

Selective polynucleotide recognition and detection based on a dual-stage method are described. The method involves the development of a recognition surface based on gold nanoparticles modified with a thiolated capture probe able to hybridize with its complementary sequence (target). After hybridization, this sensing surface is removed from the solution and electrodeposited on an electrode surface. The detection of the hybridization event is achieved using the complex [Ru(NH(3))(5)L](2+), were L is [3-(2-phenanthren-9-yl-vinyl)-pyridine], as electrochemical indicator. This complex binds to double strand DNA more efficiently than to single stranded DNA. The advantage of this dual-stage DNA sensing method is the high selectivity derived from the separation of the hybridization event (occurring on one surface) from the detection step (on a different surface), enabling the analysis of long target DNAs, which is usually the case in real DNA sequence analysis. In addition, this approach not only quantifies pmol of a complementary target sequence but also is sensitive to the presence of a single mismatch and its position in the sequence.

Diamond nanoparticles as a way to improve electron transfer in sol–gel l-lactate biosensing platforms

In the present work, we have included for the first time diamond nanoparticles (DNPs) in a sol-gel matrix derived from (3-mercaptopropyl)-trimethoxysilane (MPTS) in order to improve electron transfer in a lactate oxidase (LOx) based electrochemical biosensing platform. Firstly, an exhaustive AFM study, including topographical, surface potential (KFM) and capacitance gradient (CG) measurements, of each step involved in the biosensing platform development was performed. The platform is based on gold electrodes (Au) modified with the sol-gel matrix (Au/MPTS) in which diamond nanoparticles (Au/MPTS/DNPs) and lactate oxidase (Au/MPTS/DNPs/LOx) have been included. For the sake of comparison, we have also characterized a gold electrode directly modified with DNPs (Au/DNPs). Secondly, the electrochemical behavior of a redox mediator (hydroxymethyl-ferrocene, HMF) was evaluated at the platforms mentioned above. The response of Au/MPTS/DNPs/LOx towards lactate was obtained. A linear concentration range from 0.053 mM to 1.6 mM, a sensitivity of 2.6 μA mM(-1) and a detection limit of 16 μM were obtained. These analytical properties are comparable to other biosensors, presenting also as advantages that DNPs are inexpensive, environment-friendly and easy-handled nanomaterials. Finally, the developed biosensor was applied for lactate determination in wine samples.

One-step covalent microcontact printing approach to produce patterns of lactate oxidase

A comparative study of three different strategies to pattern lactate oxidase (LOx) onto bare gold substrates by microcontact printing (muCP) is presented. The quality of the resulting patterns in terms of homogeneity, compactness and stability has been evaluated by atomic force microscopy in both air and aqueous conditions. The following approaches have been tested: (i) LOx was directly stamped to a bare gold surface; (ii) LOx was previously covalently bonded to a thiolated molecule, dithiodipropionic acid di(N-succinimidyl ester) (DTSP), and this conjugate (LOx/DTSP) was transferred from an elastomeric stamp to a bare gold substrate; (iii) formation of a LOx/DTSP micropattern on a bare gold surface (as described in approach ii) was followed by exposure to a solution containing hexadecylmercaptane (HDM). In all cases, the catalytic activity of the final LOx patterns has been assessed by electrochemical measurements. From comparison of the three strategies, it can be concluded that the third one gives rise to LOx patterns that present a high stability and compactness, also offering the advantage of reducing the number of microcontact printing steps to one.

Electrocatalytic processes promoted by diamond nanoparticles in enzymatic biosensing devices.

We have developed a biosensing platform for lactate determination based on gold electrodes modified with diamond nanoparticles of 4nm of nominal diameter, employing the enzyme lactate oxidase and (hydroxymethyl)ferrocene (HMF) as redox mediator in solution. This system displays a response towards lactate that is completely different to those typically observed for lactate biosensors based on other nanomaterials, such as graphene, carbon nanotubes, gold nanoparticles or even diamond nanoparticles of greater size. We have observed by cyclic voltammetry that, under certain experimental conditions, an irreversible wave (E(0)=+0.15V) appears concomitantly with the typical Fe(II)/Fe(III) peaks (E(0)=+0.30V) of HMF. In this case, the biosensor response to lactate shows simultaneous electrocatalytic peaks at +0.15V and +0.30V, indicating the concurrence of different feedback mechanisms. The achievement of a biosensor response to lactate at +0.15V is very convenient in order to avoid potential interferences. The developed biosensor presents a linear concentration range from 0.02mM to 1.2mM, a sensitivity of 6.1μAmM(-1), a detection limit of 5.3μM and excellent stability. These analytical properties compare well with those obtained for other lactate-based biosensors that also include nanomaterials and employ HMF as redox mediator.

Metal release in metallothioneins induced by nitric oxide: X-ray absorption spectroscopy study

Metallothioneins (MTs) are low molecular weight proteins that include metal ions in thiolate clusters. The capability of metallothioneins to bind different metals has suggested their use as biosensors for different elements. We study here the interaction of nitric oxide with rat liver MTs by using in situ X-ray absorption spectroscopy techniques. We univocally show that the presence of NO induces the release of Zn atoms from the MT structure to the solution. Zn ions transform in the presence of NO from a tetrahedral four-fold coordinated environment in the MT into a regular octahedral six-fold coordinated state, with interatomic distances compatible with those of Zn solvated in water.

Synergistic effect of MoS 2 and diamond nanoparticles in electrochemical sensors: determination of the anticonvulsant drug valproic acid

AbstractThe authors describe an electrochemical sensor based on the use of diamond nanoparticles (DNPs) and molybdenum disulfide (MoS2) platelets. The sensor was applied to the voltammetric determination of the anticonvulsant valproic acid which was previously derivatized with ferrocene. The MoS2 platelets were obtained by an exfoliation method, and the DNPs were directly dispersed in water and subsequently deposited on a glassy carbon electrode (GCE). The sensor response was optimized in terms of the solvent employed for dispersing the MoS2 nanomaterial and the method for modifying the GCE. Sensors consisting of a first layer of MoS2 dispersed in ethanol/water and a second layer of DNPs give better response. The single steps of sensor construction were characterized by atomic force microscopy and electrochemical impedance spectroscopy. The differential pulse voltammetric response of the GCE (measured at +0.18 V vs. Ag/AgCl) was compared to that of sensors incorporating only one of the nanomateriales (DNPs or MoS2). The formation of a hybrid MoS2-DNP structure clearly improves performance. The GCE containing both nanomaterials exhibits high sensitivity (740 µA ⋅ mM−1 ⋅ cm−2), a 0.27 μM detection limit, and an 8% reproducibility (RSD). The sensor retained 99% of its initial response after 45 days of storage. Graphical abstractElectrochemical sensor by co-immobilization of MoS2 and diamond nanoparticles (DNP). The formation of a hybrid MoS2-DNP structure enhances the performance of the sensor towards valproic acid derivatized with a ferrocene group, when compared with sensors incorporating only DNP or MoS2.