E. Rubí

Solid-phase extraction followed by dispersive liquid-liquid microextraction for the sensitive determination of selected fungicides in wine.

A novel approach for the determination of seven fungicides (metalaxyl-M, penconazole, folpet, diniconazole, propiconazole, difenoconazole and azoxystrobin) in wine samples is presented. Analytes were extracted from the matrix and transferred to a small volume of a high density, water insoluble solvent using solid-phase extraction (SPE) followed by dispersive liquid-liquid microextraction (DLLME). Variables affecting the performance of both steps were thoroughly investigated (metalaxyl-M was not included in some optimisation studies) and their effects on the selectivity and efficiency of the whole sample preparation process are discussed. Under optimised conditions, 20 mL of wine were first concentrated using a reversed-phase sorbent and then target compounds were eluted with 1 mL of acetone. This extract was mixed with 0.1 mL of 1,1,1-trichloroethane (CH(3)CCl(3)) and the blend added to 10 mL of ultrapure water. After centrifugation, an aliquot (1-2 microL) of the settled organic phase was analyzed by gas chromatography (GC) with electron capture (ECD) and mass spectrometry (MS) detection. The method provided enrichment factors (EFs) around 200 times and an improved selectivity in comparison to use of SPE as single sample preparation technique. Moreover, the yield of the global process was similar for red and white wine samples and the achieved limits of quantification (LOQs) (from 30 to 120 ngL(-1) and from 40 to 250 ngL(-1), for GC-ECD and GC-MS, respectively) were low enough for the determination of target species in commercial wines. Among compounds considered in this work, metalaxyl-M and azoxystrobin were found in several wines at concentrations from 0.8 to 32 ngmL(-1).

Speciation of organomercurials in marine samples using capillary electrophoresis

A rapid method for speciation and determination of organomercury compounds in biological samples of marine origin using Capillary Electrophoresis (CE) is reported. Organomercurials were extracted from the samples by means of the classical Westöö procedure thus giving organomercury-cysteine complexes which can be separated from each other by means of CE resulting in effective speciation. Electrophoretic separation was achieved in an open silica capillary tube at 15-18 kV using a 100mM sodium borate buffer (pH 8.35). All mercury species were distinctively separated within 12 min. Results are presented for the analysis of real marine samples and reference materials, and compared with those obtained by the GC commonly accepted procedure.

Solid-phase extraction followed by liquid chromatography-tandem mass spectrometry for the determination of hydroxylated benzophenone UV absorbers in environmental water samples

A procedure for the determination of six derivatives of 2-hydroxybenzophenone, used as UV absorbers, in water samples is presented. Compounds were first concentrated using a solid-phase extraction (SPE) cartridge and then selectively determined by liquid chromatography-tandem mass spectrometry (LC-MS/MS) using electrospray ionization (ESI). The effect of different parameters on the performance of concentration and determination steps is discussed. The highly polar and acidic 2-hydroxy-4-methoxybenzophenone-5-sulfonic acid (BP-4) required the use of ammonium acetate as modifier during desorption of SPE cartridges and also to improve the performance of its separation in the LC column. Under optimized conditions, the proposed method provided limits of quantification from less than 1 to 32ngL(-1), depending on the compound and the type of water sample. Recoveries from the SPE step (83-105%) remained unaffected by the nature of the matrix; however, the efficiency of electrospray ionization was compound and sample dependant. Real sample analysis reflected the presence of three of the six investigated species (BP-4, 2-hydroxy-4-methoxybenzophenone, BP-3, and 2,4-dihydroxybenzophenone, BP-1) in the aquatic environment, particularly in raw wastewater samples. In this latter matrix, BP-4 was the compound presenting the highest concentrations; moreover, it was poorly removed in sewage treatment plants and consequently it also appeared in river water.

Simplified sample preparation method for triclosan and methyltriclosan determination in biota and foodstuff samples

An improved method for the determination of triclosan (TCS) and methyltriclosan (MTCS) in fish and foodstuff samples is presented. Analytes were simultaneously extracted and purified using the matrix solid-phase dispersion (MSPD) technique, and then selectively determined by gas chromatography with tandem mass spectrometry (GC-MS/MS). Several combinations of dispersants, clean-up co-sorbents and extraction solvents were tested in order to obtain lipid-free extracts and quantitative recoveries for TCS and MTCS. Under optimised conditions, 0.5 g samples were dispersed using 1.5 g of neutral silica in a mortar with a pestle, and transferred to a polypropylene cartridge containing 3 g of silica impregnated with 10% of sulphuric acid (SiO2-H2SO4, 10%, w/w). Analytes were recovered with 10 mL of dichloromethane whereas lipids were oxidized in the layer of acidic silica. The extract was concentrated to dryness and re-constituted with 1 mL of ethyl acetate. Then, a fraction of 0.5 mL was mixed with 50 microL of N-methyl-N-(tert-butyldimethylsilyl)trifluoroacetamide (MTBSTFA) and injected in the GC-MS/MS system. The developed method provided absolute recoveries between 77 and 120% for different samples spiked at the low ng g(-1) level, quantification limits in the range of 1-2 ng g(-1) and a considerable simplicity in comparison with previously developed sample preparation approaches. Experiments carried out placing sliced food samples in direct contact with TCS-treated kitchenware surfaces showed the capability of the biocide to migrate into foodstuffs.

Determination of selected UV filters in indoor dust by matrix solid-phase dispersion and gas chromatography―tandem mass spectrometry

A simple, inexpensive sample preparation procedure, based on the matrix solid-phase dispersion (MSPD) technique, for the determination of six UV filters: 2-ethylhexyl salicylate (EHS), 3,3,5-trimethylcyclohexyl salicylate (Homosalate, HMS), 3-(4-methylbenzylidene) camphor (4-MBC), isoamyl-p-methoxycinnamate (IAMC), 2-ethylhexyl-p-methoxycinnamate (EHMC) and octocrylene (OCR), in dust from indoor environments is presented and the influence of several operational parameters on the extraction performance discussed. Under the final working conditions, sieved samples (0.5 g) were mixed with the same amount of anhydrous sodium sulphate and dispersed with 2 g of octadecyl bonded silica (C18) in a mortar with a pestle. This blend was transferred to a polypropylene solid-phase extraction cartridge containing 2 g of activated silica, as the clean-up co-sorbent. The cartridge was first rinsed with 5 mL of n-hexane and the analytes were then recovered with 4 mL of acetonitrile. This extract was adjusted to 1 mL, filtered and the compounds were determined by gas chromatography combined with tandem mass spectrometry (GC-MS/MS). Recoveries for samples spiked at two different concentrations ranged between 77% and 99%, and the limits of quantification (LOQs) of the method between 10 and 40 ng g(-1). Analysis of settled dust from different indoor areas, including private flats, public buildings and vehicle cabins, showed that EHMC and OCR were ubiquitous in this matrix, with maximum concentrations of 15 and 41 microg g(-1), respectively. Both UV filters were also quantified in dust reference material SRM 2585 for first time. EHS, 4-MBC and IAMC were detected in some of the analyzed samples, although at lower concentrations than EHMC and OCR.

Optimization of pressurized liquid extraction and purification conditions for gas chromatography-mass spectrometry determination of UV filters in sludge.

This work presents an effective sample preparation method for the determination of eight UV filter compounds, belonging to different chemical classes, in freeze-dried sludge samples. Pressurized liquid extraction (PLE) and gas chromatography-mass spectrometry (GC-MS) were selected as extraction and determination techniques, respectively. Normal-phase, reversed-phase and anionic exchange materials were tested as clean-up sorbents to reduce the complexity of raw PLE extracts. Under final working conditions, graphitized carbon (0.5 g) was used as in-cell purification sorbent for the retention of co-extracted pigments. Thereafter, a solid-phase extraction cartridge, containing 0.5 g of primary secondary amine (PSA) bonded silica, was employed for off-line removal of other interferences, mainly fatty acids, overlapping the chromatographic peaks of some UV filters. Extractions were performed with a n-hexane:dichloromethane (80:20, v:v) solution at 75°C, using a single extraction cycle of 5 min at 1500 psi. Flush volume and purge time were set at 100% and 2 min, respectively. Considering 0.5 g of sample and 1 mL as the final volume of the purified extract, the developed method provided recoveries between 73% and 112%, with limits of quantification (LOQs) from 17 to 61 ng g(-1) and a linear response range up to 10 μg g(-1). Total solvent consumption remained around 30 mL per sample. The analysis of non-spiked samples confirmed the sorption of significant amounts of several UV filters in sludge with average concentrations above 0.6 μg g(-1) for 3-(4-methylbenzylidene) camphor (4-MBC), 2-ethylhexyl-p-methoxycinnamate (EHMC) and octocrylene (OC).

Suitability of polypropylene microporous membranes for liquid- and solid-phase extraction of halogenated anisoles from water samples.

The applicability of disposable polypropylene microporous membranes (MMs) for the concentration of five halogenated anisoles in water samples was investigated. Two microextraction approaches, named MM solid-phase extraction (MMSPE) and liquid-liquid extraction (MMLLE), are proposed. They are based on adsorption of target species onto the surface of the dry membrane and absorption into a few microlitres of solvent embedded in the pores of the membrane, respectively. The effect of several factors, such as sampling mode, type of acceptor solvent, ionic strength of the sample, stirring, sampling time, etc., on the performance of both approaches was thoroughly assessed. After extraction, analytes were recovered from the sorbent using just 0.25 m L of n-hexane and determined by gas chromatography with micro-electron-capture detection (GC-micro-ECD). Under optimised conditions, similar precisions (RSDs from 7% to 14%, under reproducibility conditions) and limits of quantification (values between 0.3 and 15 ng L(-1)), as well as remarkable linear responses were attained for both techniques; however, MMSPE, operating in the headspace sampling mode (HS), showed faster kinetics for all species, was less affected by the type of matrix and the set-up of the extraction step was simpler, since immobilisation of the extraction solvent in the membrane was not necessary. Obtained results demonstrated, for the first time, the suitability of polypropylene MMs as adsorbents of lipophilic compounds.

Evaluation of capillary columns used in the routine determination of methylmercury in biological and environmental materials

Abstract The factors determining the effective life of the capillary columns commonly used in the determination of organomercury compounds in biological and environmental materials were examined. The effects of pretreatment of these columns with mercury(II) salts on their behaviour and the duration of the treatments in terms of the type of stationary phase considered are discussed, in addition to the influence of the thickness of the stationary phase and the external protective covering of the columns. The use of diphenyldimethylsiloxane columns with a film thickness of 5 μm seems to be the most advantageous option for routine analysis.

Solid-phase microextraction followed by gas chromatography–mass spectrometry for the determination of ink photo-initiators in packed milk

A novel, single step method for the determination of seven ink photo-initiators in carton packed milk samples is described. Solid-phase microextraction (SPME) and gas chromatography (GC), combined with mass spectrometry (MS), were used as sample preparation and determination techniques, respectively. Parameters affecting the performance of the microextraction process were thoroughly evaluated using uni- and multivariate optimization strategies, based on the use of experimental factorial designs. The coating of the SPME fibre, together with the sampling mode and the temperature were the factors playing a major influence on the efficiency of the extraction. Under final conditions, 1.5 mL of milk and 8.5 mL of ultrapure water were poured in a glass vessel, which was closed and immersed in a water boiling bath. A poly(dimethylsiloxane)-divinylbenzene (PDMS-DVB) coated fibre was exposed directly to the diluted sample for 40 min. After that, the fibre was desorbed in the injector of the GC-MS system for 3 min. The optimized method provided limits of quantification (LOQs) between 0.2 and 1 microg L(-1) and a good linearity in the range between 1 and 250 microg L(-1). The inter-day precision remained below 15% for all compounds in spiked whole milk. The efficiency of the extraction changed for whole, semi-skimmed and skimmed milk; however, no differences were noticed among the relative recoveries achieved for milk samples, from different brands, with the same fat content.

Studies on organo-mercury compounds speciation

Four studies on organo-mercury compounds speciation carried out in the analytical chemistry laboratory of the University of Santiago are briefly described and discussed. Search for new methods of separation based on liquid chromatography as well as quality control and application studies have been started and the results obtained up to the end of 1990 are presented.